JIKONG JK-BD4A8S4P, JK-BD4A8S6P

Contents

JIKONG Smart Active Balancer BMS User Manual

Models: JK-BD4A8S4P, JK-BD4A8S6P

1. Product Overview

The JIKONG Smart Active Balancer Battery Management System (BMS) is an intelligent power management solution designed for various battery chemistries, including Li-ion, LiFePO4, and LTO batteries. It supports battery configurations from 4S to 8S (3S-8S for Li-Ion) and features active balancing technology to ensure optimal battery performance and longevity.

This BMS is equipped with a high-performance MCU (Main Control Unit) and offers multiple interfaces for comprehensive data monitoring and control. Its robust aluminum alloy shell provides superior heat dissipation and protection against external environmental factors, including anti-voltage and anti-vibration properties.

JIKONG Smart BMS with scooter and battery, highlighting key features
Figure 1: JIKONG Smart BMS integrated into a battery system, showcasing its multi-interface display and active balancing capabilities.

Key Features:

  • Active Balancing: Energy transfer balancing from higher to lower energy cells, ensuring minimal energy loss and extended battery lifespan.
  • Wide Compatibility: Supports 3S-8S Li-ion, 4S-8S LiFePO4, and 6S-8S LTO battery series.
  • Multi-Interface Support: Includes GPS, RS485, CAN, Display, Heat, and NTC interfaces.
  • Smart Monitoring: Mobile APP (iOS, Android, HarmonyOS) and PC software for real-time data display (voltage, current, temperature, SOC, alarms, cycles).
  • Adjustable Protection Parameters: User-configurable overcharge, over-discharge, overcurrent, and temperature protection values.
  • Robust Design: Fully aluminum alloy shell for excellent heat dissipation and enhanced durability.
  • Certifications: CE, FCC, RoHS compliant.

2. Package Contents

Before installation, please verify that all items listed below are present and in good condition.

  • BMS Unit x 1
  • Sampling Line x 1 (70cm long)
  • NTC Temperature Sensor x 1 (40cm long)
  • Switch Key x 1 (50cm long)
JIKONG BMS packing list showing the BMS unit, sampling line, NTC, and switch key
Figure 2: Contents of the JIKONG Smart BMS package.

3. Installation and Wiring

Proper installation and wiring are crucial for the safe and efficient operation of your JIKONG BMS. Please follow these steps carefully. Refer to the wiring diagrams for your specific battery string configuration.

General Wiring Steps:

  1. Connect all balance cables: Ensure each cell's balance wire is correctly connected to the corresponding pin on the BMS sampling port.
  2. Insert the balance cable into the BMS: Carefully plug the assembled balance cable into the designated port on the BMS.
  3. Connect the B-line and P-line to the battery: Connect the main negative terminal (B-) of the battery pack to the B- terminal on the BMS. Connect the main negative output terminal (P-) of the BMS to your load/charger. The total positive electrode (P+) of the battery pack connects directly to the load/charger.

Wiring Diagrams:

Wiring diagram for a 4-string battery cell configuration with JIKONG BMS
Figure 3: Wiring method for 4-string cells. Note the connections for B-, P-, P+, and individual cell balance wires (1S, 2S, 3S, 4S).
Wiring diagram for an 8-string battery cell configuration with JIKONG BMS
Figure 4: Wiring method for 8-string cells. This diagram illustrates connections for B-, P-, P+, and individual cell balance wires (1S through 8S).

Important: Always ensure correct polarity and sequence when connecting the BMS to prevent damage to the unit or battery pack. Incorrect wiring can lead to serious hazards.

4. Operation

The JIKONG Smart BMS offers intelligent interaction and easy operation through its dedicated mobile application and PC software.

4.1 Mobile APP and PC Software

The "JIKONG SMART BMS" mobile application is available for iOS, Android, and HarmonyOS devices. It provides a personal lithium battery steward, displaying all essential information at a glance. The APP supports multiple languages, which can be switched automatically with your mobile phone system.

You can freely choose between the mobile APP, PC software, or a JIKONG home storage display for monitoring and data visualization.

Multi-screen display options for JIKONG BMS, including mobile app, PC software, and dedicated display
Figure 5: Various display options for monitoring BMS data, including mobile app, PC software, and dedicated home storage display.

4.2 Data Monitoring and Parameter Adjustment

Through the APP or PC software, you can view multiple information such as voltage, current, temperature, and number of strings. The system allows for free adjustment of various protection values, including overcharge, over-discharge, overcurrent, temperature, and balance parameters.

Caution: Before adjusting any parameters, it is recommended to first read and understand the internal parameters of the protection board to avoid unintended configurations.

4.3 Inverter Communication Protocol

The JIKONG BMS supports protocol docking with mainstream inverter communication protocols in the market, allowing for fast and convenient integration. This can be easily set up through the mobile APP or PC software.

JIKONG BMS app interface showing CAN protocol selection and a list of supported inverter protocols
Figure 6: Mobile APP interface for selecting and configuring CAN communication protocols with various inverters.
PC software interface for setting inverter communication protocols
Figure 7: PC software interface for advanced settings, including inverter communication protocols.

Supported CAN Protocols:

Protocol NameCompatible Brands
JIKONGJIKONG
NIUNIU
China TowerChina Tower
GrowattGrowatt
VoltronicVoltronic
WOWWOW
Low-voltage hybrid inverter CAN communication protocolDeye, Pylontech, Growatt, Victron Energy, INVT, SMA, SRNE

5. Maintenance

The JIKONG BMS incorporates intelligent active balancing technology, which is a key aspect of maintaining battery health and extending its lifespan.

Active Balancing (Lossless Balancing)

Active balancing is achieved through energy transfer, moving energy from cells with higher voltage to cells with lower voltage. This process ensures voltage balance across all cells with minimal energy loss. It operates continuously, whether the battery is charging, discharging, or idle, until the voltage difference is within the set range.

Unlike passive balancing, active balancing does not generate significant heat, allowing for larger balancing currents (typically 1A-2A). This makes it particularly suitable for larger capacity battery packs where maintaining cell balance is critical for performance and safety.

Diagram illustrating active balancing process in a battery pack
Figure 8: Visual representation of active balancing, showing energy transfer between cells to achieve equilibrium.

Battery Health Monitoring

Regularly monitor your battery's health parameters via the JIKONG APP or PC software. Pay attention to cell voltage differences, temperature, and overall State of Charge (SOC) to identify any potential issues early.

6. Troubleshooting

This section provides guidance on common issues you might encounter with your JIKONG Smart BMS.

Common Issues and Solutions:

  • BMS Not Powering On:
    • Check all wiring connections, especially the main B- and P- lines, and the balance cables.
    • Ensure the battery pack voltage is within the operating range of the BMS.
    • Verify the switch key is correctly connected and activated.
  • Cell Imbalance Detected:
    • The active balancing feature should address minor imbalances automatically. Allow sufficient time for balancing to occur, especially with large capacity packs.
    • Check individual cell voltages via the APP/PC software to identify severely unbalanced cells.
    • Ensure balance cables are securely connected and not damaged.
  • Overcharge/Over-discharge Protection Triggered:
    • These protections are designed to safeguard your battery. Check your charger/load settings to ensure they are within safe operating limits.
    • Review the protection parameters set in the BMS APP/PC software. Adjust if necessary, but always understand the implications of changes.
  • Overcurrent/Short Circuit Protection Triggered:
    • This indicates excessive current draw or a short circuit in the system. Immediately disconnect the load and inspect for faults.
    • Ensure your load's current requirements do not exceed the continuous or maximum discharge current of your BMS model.
  • Bluetooth Connection Issues:
    • Ensure Bluetooth is enabled on your mobile device.
    • Make sure the BMS is powered on and within range.
    • Restart the mobile application or your device.

7. Specifications

The JIKONG Smart Active Balancer BMS comes in several models, each with specific characteristics. Please refer to the table below for detailed specifications.

Table of JIKONG Product Specifications for various BMS models
Figure 9: Detailed product specifications for JIKONG BMS models.
Technical IndexJK-B1A8S10PJK-B1A8S20PJK-B2A8S20PJK-B2A8S30P
Number of Battery Strings (Li-Ion)3S-8S
Number of Battery Strings (LiFePO4)4S-8S
Number of Battery Strings (LTO)6S-8S
Balance MethodActive Balance (Full State On)
Balance Current1A1A2A2A
Conductive Resistance in Main Circuit0.3mΩ
Continuous Discharge Current100A200A200A300A
Maximum Discharge Current (MAX 2min)200A300A300A400A
Over Charge Protection (ADJ)10-100A10-200A10-200A10-300A
Other Interfaces (Customized)RS485RS485CANBUS HEATCANBUS HEAT
Size (mm)153*126*18189*94*24
Wiring OutputCommon Port
Single Cell Voltage Range1-5V
Voltage Acquisition Accuracy±5mV
Over Charge Protection Voltage1.2-4.35V Adjustable
Over Charge Release Voltage1.2-4.35V Adjustable
Over Current Detect Delay2-120S Adjustable
Over Discharge Protection Voltage1.2-4.35V Adjustable
Over Discharge Release Voltage1.2-4.35V Adjustable
Quantity of Temperature Detection1 Pcs
Temp ProtectionYes
Short Circuit ProtectionYes
Coulomb CounterYes
Bluetooth FunctionSupport for Android iOS

Dimensions:

  • JK-B1A8S10P: 105mm (width) x 153.9mm (height) x 17.6mm (thickness)
  • JK-B2A8S20P: 126mm (width) x 153mm (height) x 17.6mm (thickness)
  • JK-B2A8S30P: 127.26mm (width) x 174.77mm (height) x 17.6mm (thickness)

Note: Data tolerance range is ±2mm.

8. User Tips

  • 3S Li-Ion Compatibility: The JIKONG BMS supports 3S Li-Ion battery configurations, making it suitable for applications using 18650 lithium-ion cells in a 3-series arrangement.
  • Parameter Adjustment Caution: When adjusting protection values (overcharge, over-discharge, overcurrent, temperature, balance) via the APP or PC software, always review the default or current internal parameters first. Understand the impact of any changes before applying them to ensure safe and optimal battery operation.
  • Regular Monitoring: Periodically check the battery status through the mobile app or PC software to monitor cell voltages, temperatures, and overall performance. This helps in early detection of potential issues.
  • Firmware Updates: Check the official JIKONG website (WWW.JK-BMS.COM) or app for any available firmware updates to ensure your BMS has the latest features and bug fixes.

9. Warranty and Support

For warranty information, please refer to the terms and conditions provided by your seller or contact JIKONG Official Store directly. Technical support and additional resources can be found on the official JIKONG website: WWW.JK-BMS.COM.

The mobile application also serves as a primary support interface for monitoring and configuration.

© 2024 JIKONG Official Store. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.