1. Safety Warnings and Regulations
1.1 Regulations and Safety Warnings
Thank you for purchasing this product. This dual band/dual display/dual watch radio provides secure, instant, and reliable communications. Please read this manual carefully before use to ensure maximum performance and safe operation.
EU Regulatory Conformance
As certified by the qualified laboratory, the product complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. All applicable EU regulations are regarded (2006/66/EC, 2011/65/EU, (EU)2015/863, 2012/19/EU). Note: It can be operated under 2000m.
WARNING! European Users should note that operation of this unit in Transmit mode requires the operator to have a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the “EU” specification guide 2014/53/EU. This information is applicable to EU countries only.
Compliance with RF Exposure Standards
The radio complies with the following RF energy exposure standards and guidelines:
- United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093
- American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015
- Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition
RF Exposure Compliance and Control Guidelines and Operating Instructions
To control your exposure and ensure compliance with occupational/controlled environmental exposure limits, always adhere to the following procedures:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
- Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key.
- Keep the radio unit at least 2.5cm away from the face. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product.
- Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
- Contact your local dealer for the product's optional accessories.
Precautions for Portable Terminals
Operating Prohibitions
To protect against property loss, bodily injury or death, observe the following safety instructions:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
Important Tips
To help you make better use of the product, observe the following instructions:
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Please operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation. Keep it at a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify or repair the product and its accessories without authorization.
2. Setup and Initial Use
2.1 Content of the Packaging
The package includes:
- 1 Radio
- 1 USB-C cable
- 1 Antenna
- 1 Li-Ion battery pack (3000mAh)
- 1 Wrist strap
- 1 Belt clip
- 1 Manual

2.2 Installation of Accessories
Installing/Removing the Antenna
- Installing: Align the antenna with the antenna port. Rotate clockwise until fully tightened.
- Removing: Rotate the antenna counterclockwise until it is completely detached.
Installing the Belt Clip
- Align the grooves of the belt clip with those of the radio and push down until you hear a click.
- To remove, use a flat-bladed object to press the belt clip tab away from the radio, then slide the clip upward.
Installing the Battery Pack
Before attaching or removing the battery, ensure the radio is turned off by turning the power/volume knob all the way counter-clockwise.
- Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
- Once aligned with the guide-rails, slide the battery upward until you hear a click as it locks in place.
Removing the Battery Pack
To remove the battery, press the battery release above the battery pack, as you slide the battery downward.
Installing the Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
2.3 Charging the Battery
The Li-ion battery pack is not charged at the factory; please charge it before use. For best operation, fully charge/discharge the battery two or three times before it reaches its best performance.
Charging Methods
This radio supports two charging methods: Type-C USB charging and desktop charging (desktop charger not included).
Using the Type-C USB Charger
- Make sure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end to a wall power outlet.
- An empty battery will be fully charged in approximately 4 hours.
- The battery meter on the LCD will move to indicate charging.
Note: It is recommended to power OFF your radio while charging. For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio while connected to the charger.

Using the Desktop Charger (not included)
- Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the charger. The indicator light blinks orange, indicating it's ready to charge.
- Plug the battery or the radio into the charger. Ensure good contact between battery terminals and charging terminals. The indicator light turns red, indicating charging.
- It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, charging is complete.
LED Indicator Status
| STATUS | LED |
|---|---|
| No Battery | Green and red alternately flashing |
| Charge Normally | Red |
| Fully Charged | Green |
| Trouble | Red blinks fast for a long time |
NOTE: Trouble means battery too warm, battery short-circuited or charger short-circuited.
3. Radio Overview
3.1 Buttons and Controls

The XHDATA E100 features a 1.44-inch color large screen display for improved visibility. It has a full keyboard for easy operation.

3.2 LCD Display Icons
| Icon | Description | Icon | Description |
|---|---|---|---|
| Mxxx | Memory channel | DW | Dual watch enabled |
| VFO | Frequency Mode | TX | Transmitting |
| VOX | VOX enabled | RX | Receiving |
| CTC | CTCSS enabled | R | Reverse function enabled |
| DCS | DCS enabled | ► | Indicates active band or channel |
| N | Narrowband enabled | +/- | Frequency shift direction if enabled in VFO |
| H/L | Transmit power level indicator According to Power (High/Low) | Battery level indicator | |
| Squelch Open/Close Indicator |
3.3 Status Indications
The status LED has a very simple and traditional design. When you receive a signal it turns green, when you transmit it turns red, and it's off in standby.
| LED Indicator | Radio Status |
|---|---|
| Constant Red | Transmitting. |
| Constant Green | Receiving. |
3.4 Main Keypad Controls
- V/M: Short press to switch frequency or channel mode. Press and hold to toggle channel display mode: CH/FREQ/NAME.
- A/B: Short press to toggle upper screen (A)/lower screen (B). Press and hold to switch Double Wait/Signal Wait/Dual Watch off modes.
- One-Touch search key: Short press to enter One-Touch search key.
- EXIT: Short press to return to menu or return to previous menu. (Press and hold to enter frequency sweep mode).
- *: Long press to lock or unlock the keypad.
- #: Short press to enter DTMF dial. Press and hold to scan on and scan off.
- 0[space]: Press and hold to enter weather switch to select weather channel.
3.5 Programmed Keys
It is possible to set different functions for [SK1] (flashlight/alarm switch) and [SK2] (radio/monitor) keys. Method 1: In radio Menu – 48/49/50 PF1 Press/PF1 LongPre/PF2 Press.
| Function | Description |
|---|---|
| None | No function |
| Torch On/Off | Quick switch torch |
| Power Select | Quickly switch between high, low transmit power. |
| Scan On/Off | Quickly switch scanning function on or off. |
| VOX On/Off | Quickly switch on/off VOX function |
| Alarm on/off | Quickly establishes an emergency call. |
| Radio on/off | Quickly switch on or off the FM radio function. |
4. Basic Operations
4.1 Power On/Off
- To turn the unit on, simply rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash the LCD, then display a frequency or channel.
- To turn the unit off, turn the Volume/Power knob counter-clockwise all the way until you hear a "click".
4.2 Adjusting the Volume
- To turn up the volume, turn the Volume/Power knob clockwise.
- To turn down the volume, turn the Volume/Power knob counter-clockwise.
4.3 Main Band/Sub Band Select
In standby mode, press the [A/B] key to switch between A (upper) and B (lower) displays. The frequency or channel on the selected display becomes the active listening and transmit frequency or channel.
4.4 VFO/Channel Switch
Press the [V/M] key to switch between VFO (Frequency) and Channel (MR) display modes.
- In channel mode (MR), the channel number will be displayed on the left.
- In frequency mode (VFO), 'VFO' will be displayed on the left.
4.5 Frequency (VFO) Mode
In VFO mode, you can navigate up and down the band using the ▲/▼ keys or input frequencies directly on the numeric keypad with kilohertz accuracy.
WARNING! Transmitting on unauthorized frequencies is illegal and a serious offense. Contact your local regulatory body for information on applicable laws.
The scanning and receive function of the aviation frequency band (AM108-136MHz) and the police frequency band (350-390MHz) is limited to VFO mode and allows manual input of these frequencies. Prohibit use in channel mode.
4.6 Channel (MR) Mode and Channel Selection
In Channel (MR) mode, you can navigate up and down the channel using the ▲/▼ keys or the encoder.
- Operation 1: Press the ▲/▼ navigation key to select the channel.
- Operation 2: Input the channel numbers by the keyboard (e.g., for channel 12, input [0][1][2]).
4.7 Making a Call
NOTE: Press the [A/B] key to switch the main channel if two channels are shown on the display.
- Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with a normal tone. The red LED will be on.
- Frequency mode call: Press [V/M] key to switch to frequency mode, input the working frequency, and press and hold the [PTT] key to transmit. The red LED will be on.
- Receive a call: When you release the [PTT] key, you can answer without any action. The green LED will be on when receiving a call.
NOTE: To ensure the best reception volume, keep the distance between the microphone and the mouth at 2.5 cm to 5 cm during transmission.
4.8 Using the Flashlight
You can use the high-intensity LED flashlight on your radio:
- Press [SK1] key once to turn on continuously (Always On mode).
- Press [SK1] key again for Strobe Light emergency signal (Strobe emergency mode).
- Press [SK1] key a third time to turn off the light.

4.9 Emergency Alert
The Emergency Alert feature can be used to signal members in your group for help.
- To activate, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash.
- Press the [SK1] key to exit the emergency alert function.
WARNING: The Emergency Alert feature should only be used in the event of an actual emergency.
4.10 FM Radio
The frequency range for the FM radio is 65-108MHz.
- In frequency or channel mode, press [SK2] key to turn on the radio.
- Select the desired radio frequency with the ▲/▼ keys or input the frequency. Alternatively, press #z to automatically search a radio station.
- Press [SK2] key to exit FM radio.
Note: While listening to the radio, if an A/B receiving signal is detected, the radio will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears, the radio will switch back to FM radio mode.
4.11 Monitor
In standby, press and hold the [SK2] key to enter Monitor. This function allows monitoring weak signals even if the matched carrier's signaling is too weak. Stop pressing the [SK2] key to turn off the speakers and return to standby mode.
4.12 Keypad Lock
The radio features a keypad lock that locks out all keys except for the three side keys.
- To enable or disable, press and hold the * key for about two seconds.
- You can also enable automatic keypad lock after ten seconds from the menu.
4.13 Frequency Reversal
A short momentary press of the * key enables the reverse function. If you want to listen to the repeater's input frequency instead, press * key momentarily and you'll reverse your transmit and receive frequencies. This is indicated by an 'R' on the LCD.
4.14 TX Repeaters Tone
Press [PTT] + [SK2] key to send a 1750Hz repeaters tone. This function is useful for communications through repeaters. If the keypad lock is enabled, you can still send a 1750Hz tone.
4.15 One-Touch Frequency Search
- Press and hold the * key; the screen will display “SEARCH SWEEK...”.
- If the unit receives an effective frequency, it will be displayed along with any CTCSS or DCS values.
- Press the [MENU] key to save the Search frequency and CTCSS or DCS to a channel.
Note: During frequency Search, press the #z key to switch between UHF or VHF bands.
4.16 Weather Radio/Scan Weather Channel (NOAA)
Your radio has a NOAA Weather Radio function to receive weather reports from designated NOAA stations, and a NOAA Weather Scan function to scan all 10 NOAA Weather Radio channels.
- To turn the NOAA Weather Scan on, press the [OSQL] key for 3 seconds; a cloud icon appears, and the radio enters Weather band mode.
- Press and hold the #z key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding #z again will stop the scan.
- After stopping NOAA weather scan, you can manually select the weather channel by pressing the ▲/▼ key.
- To exit Weather Radio broadcast mode, press the [EXIT] key or [PTT] key.
Weather Channel Frequencies and Names
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| Wx-01 | 162.550 | Wx-06 | 162.500 |
| Wx-02 | 162.400 | Wx-07 | 162.525 |
| Wx-03 | 162.475 | Wx-08 | 161.650 |
| Wx-04 | 162.425 | Wx-09 | 161.775 |
| Wx-05 | 162.450 | Wx-10 | 163.275 |
NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
5. Advanced Features
5.1 Working the Menu System
Basic Use with Arrow Keys
- Press the [MENU] key to enter the menu.
- Use the ▲/▼ keys to navigate between menu items.
- Press [MENU] again to select the desired menu item.
- Use the ▲/▼ keys to select the desired parameter.
- To confirm your selection, press [MENU]. To cancel changes, press [EXIT].
- To exit the menu at any time, press [EXIT].
Using Shortcuts
Every menu item has a numerical value for direct access.
- Press the [MENU] key to enter the menu.
- Use the numerical keypad to enter the number of the menu item.
- Press the [MENU] key to enter the menu item.
- For parameters, use arrow keys or numerical keypad for short-cut code.
- To confirm your selection, press [MENU].
5.2 Scanning
The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. To enable the scanner, press and hold the #z key for about two seconds. Press and hold the #z key again to exit scanning mode.
Scanning Modes
The scanner is configurable to one of three ways of operation: Time (TO), Carrier (CO), or Search (SE).
- Press [MENU] to enter the menu.
- Enter 19 on your numeric keypad to go to scanner mode.
- Press [MENU] to select.
- Use the ▲/▼ keys to select scanning mode.
- Press [MENU] to confirm and save.
- Press [EXIT] to exit the menu.
- Time Operation (TO): Scanner stops when it detects a signal, and resumes after a preset time out.
- Carrier Operation (CO): Scanner stops when it detects a signal, and resumes after a preset time with no signal.
- Search Operation (SE): Scanner stops when it detects a signal. To resume scanning, press and hold the #z key again.
Frequency Scanning
In frequency mode, press #z key for more than 2 seconds to start scanning. Change direction with ▲/▼ keys. Press #z to stop.
Channel Scanning
In channel mode, press #z key for more than 2 seconds to start scanning. Change direction with ▲/▼ keys. Press #z to stop.
Scan CTCSS/DCS
These functions allow scanning frequencies with CTCSS or DCS tones enabled. In standby mode, press [MENU] [1][6] for CTCSS or [MENU] [1][7] for DCS, then [MENU] to start the scan.
5.3 Manual Programming (Channels Memory)
The radio features 999 memory channels. Each can hold receive and transmit frequencies, transmit power, signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier.
Example 1: Programming a Channel Repeater Offset with CTCSS Tone
To program a new memory in Channel 10 with RX = 432.55000 MHz, TX = 437.55000 MHz (+5 Offset), and TX CTCSS tone 123.0:
- Press [EXIT] to switch between menus.
- Press [V/M] key to set the radio to VFO mode.
- [MENU] [1][4] [MENU] [1] [0] [MENU] [EXIT] (Deletes prior data in channel 10).
- [MENU] [0][5] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone).
- Enter RX frequency (e.g., 43255000).
- [MENU] [1][3] [MENU] [1][0] [MENU] --> [EXIT] (Enters desired channel 10, RX has been added).
- Enter TX frequency (e.g., 43755000).
- [MENU] [1][3] [MENU] [1][0] [MENU] --> [EXIT] (Enters same channel 10, TX has been added).
- Press [V/M] key to return to MR mode.
Example 2: Programming a Simplex Channel with CTCSS Tone
To program a new memory in Channel 10 with RX = 432.6625 MHz and TX CTCSS tone 123.0:
- Press [EXIT] key to switch between menus.
- Press [V/M] key to set the radio to VFO mode.
- [MENU] [1][4] [MENU] [1] [0] [MENU] [EXIT] (Deletes prior data in channel 10).
5.4 Repeaters Programming
These instructions assume you know the transmit and receive frequencies your repeater employs and are authorized to use it.
- Press [V/M] key to set the radio to VFO mode.
- Use the numeric keypad to enter the repeater's output (your receiving) frequency.
- Press the [MENU] key to enter the menu.
- Enter [1][2] on the numeric keypad to get to frequency offset.
- Press [MENU] key to select.
- Use the numerical keypad to enter the specified frequency offset.
- Press [MENU] key to confirm and save.
- Enter [1][1] on the numeric keypad to get to offset direction.
- Use the ▲/▼ keys to select + (positive) or - (negative) offset.
- Press [MENU] key to confirm and save.
- (Optional) Save to memory or set up CTCSS.
- Press [EXIT] key to exit the menu.
5.5 VOX (Voice Activated Transmit)
This function allows hands-free conversations. Just speak in the direction of the microphone, and communication will be automatically activated.
- In standby mode, press [MENU] + 25. The screen will display “VOX Switch”. Press [MENU] to enter, then use ▲/▼ keys to turn ON/OFF.
- In standby mode, press [MENU] + 26. The screen will display “VOX Level”. Press [MENU] to enter, then use ▲/▼ keys to select VOX level (1-9), then [MENU] to confirm.
NOTE: Level 1 is the least sensitive, while level 9 is the most sensitive. VOX is not enabled in Scan or FM Radio mode.
5.6 Dual Watch
The radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.
Enabling or Disabling Dual Watch Mode
- Press the [MENU] key to enter the menu.
- Enter 38 on the numeric keypad to get to Dual Watch.
- Press [MENU] key to select.
- Use the ▲/▼ keys to select Double Wait/Signal Wait/OFF.
- Press [MENU] key to confirm.
- Press the [EXIT] key to exit the menu.
5.7 Stopwatch Timer
In standby mode, press [MENU] + 57. The screen displays “STOP WATCH”. Press [MENU] to start/restart counting. Press [EXIT] to exit.
5.8 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method used for automation systems and remote control in two-way radio systems.
DTMF Frequencies and Corresponding Codes
| 1209Hz | 1336Hz | 1477Hz | 1633Hz | |
|---|---|---|---|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
To send DTMF codes, press the key(s) corresponding to the message while holding down the PTT key.
5.9 Customization
The radio allows you to define visual and audible features to suit your usage habits.
Display Backlight (ABR) - MENU 51
In standby mode, press [MENU] + 51. The screen will display “ABR”. Press [MENU] to enter, use ▲/▼ keys to select always on/required delay time (ON/5sec/10sec/15sec/20sec), then [MENU] to confirm.
Beep Prompt (BEEP) - MENU 32
If enabled, a beep tone will sound every time a key is pressed. In standby mode, press [MENU] + 32. The screen will display “BEEP PROMPT”. Press [MENU] to enter, use ▲/▼ keys to turn ON/OFF, then [MENU] to confirm.
Voice Function (VOICE) - MENU 30
In standby mode, press [MENU] + 30; the screen will display “VOICE”. Press [MENU] to enter, use ▲/▼ keys to select OFF/ON, then [MENU] to confirm.
Language of the Menu (LANGUAGE) - MENU 29
This section shows the language of the MENU (English). In standby mode press [MENU] + 29. The display will show “LANGUAGE”.
Working Mode (MDF-A) - MENU 39
The radio has four working modes: Frequency mode (FREQ), Channel mode (CH), Channel name (NAME). To shift, in Standby mode press [MENU] + 39; select the desired working mode with the ▲/▼ keys, then [MENU] to confirm.
Roger Beep (ROGER) - MENU 33
Roger Beep can be enabled/disabled. In standby mode, press [MENU] + 33; the screen will display “ROGER”. Press [MENU] to enter, use ▲/▼ keys to select OFF/ON, then [MENU] to confirm.
Power On Message (POWER ON MSG) - MENU 40
Customize the welcome message that appears on the display when the radio is switched on. Options include VOLTAGE, MESSAGE, or LOGO. In Standby mode press [MENU] + 40; select the desired option and confirm with MENU.
Power On Password (Power On PWD) - MENU 37
Request a password when the radio is turned on. In standby mode, press [MENU] + 37. Press [MENU] to enter, use ▲/▼ keys to enable/disable (ON/OFF), then [MENU] to confirm. The default startup password is 000000.
Reset - MENU 56
This transceiver has two Reset modes: VFO and ALL.
- Reset VFO: Resets frequency settings only. In standby mode, press [MENU] + 56; select VFO, then [MENU] to confirm.
- Reset ALL: Resets all settings to factory defaults. In standby mode, press [MENU] + 56; select ALL, then [MENU] to confirm.
6. Maintenance
6.1 Precautions for Batteries
Charging Prohibitions
- Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres.
- Do not charge a wet battery; dry it with a soft, clean cloth first.
- Do not charge a battery suffering deformation, leakage, or overheating.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location with strong radiation.
- Overcharging may shorten battery life.
Maintenance Instructions
- Clean accumulated dust on the charging connector regularly with a clean, dry cloth.
- Charge the battery under 5°C~40°C.
- To charge a battery attached to the product, turn it off for a full charge.
- Do not remove the battery or unplug the power cord during charging.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight or other heating sources.
- Do not squeeze, penetrate, or remove the housing of the battery.
WARNING!
When keys, ornamental chain, or other electric metals contact the battery terminal, the battery may become damaged or injure a human. If the battery terminals are short-circuited, it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.
6.2 How to Store the Battery
- If the battery needs to be stored, keep it at 80% discharged.
- Store in a low temperature and dry environment.
- Keep it away from hot places and direct sunlight.
- Do not short circuit the battery terminals.
- Never attempt to remove the casing from the battery pack.
- Never store the battery in unsafe surroundings, as a short may cause an explosion.
- Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.
7. Troubleshooting Guide
| Phenomena | Analysis | Solution |
|---|---|---|
| You cannot turn on the radio. | The battery may be installed improperly. The battery power may run out. The battery may suffer from poor contact caused by dirty or damaged battery contacts. | Remove and reattach the battery. Recharge or replace the battery. Clean the battery contacts or replace the battery. |
| During receiving, the voice is weak or intermittent. | The battery voltage may be low. The volume level may be low. The antenna may be loose or installed incorrectly. The speaker may be blocked. | Recharge or replace the battery. Increase the volume. Turn off the radio, then remove and reattach the antenna. Clean the surface of the speaker. |
| You cannot communicate with other group members. | The frequency or signaling type may be inconsistent with that of other members. | Verify that your TX/RX frequency and signaling type are correct. |
| You hear unknown voices or noise. | You may be too far away from other members. You may be interrupted by radios using the same frequency. The radio in analog mode may be set with no signaling. | Move towards other members. Change the frequency, or adjust the squelch level. Request your dealer to set signaling for the current channel to avoid interference. |
| You are unable to hear anyone because of too much noise and hiss. | You may be too far away from other members. You may be in an unfavorable position (e.g., blocked by high buildings or underground areas). It may be the result of external disturbance (e.g., electromagnetic interference). | Move towards other members. Move to an open and flat area, restart the radio, and try again. Stay away from equipment that may cause interference. |
| The radio keeps transmitting. | VOX may be turned on or the headset is not installed in place. | Turn off the VOX function. Check that the headphones are in place. |
NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.
8. Technical Specifications
| Parameter | Value |
|---|---|
| Frequency band | FM65-108MHz; AM108-136MHz(Rx); 350-390MHz(Rx); 136-174MHz (Rx/Tx); 220-260MHz (Rx/Tx); 400-520MHz (Rx/Tx); |
| Memory channels | 999 |
| Power supply | Li-Ion battery 7.4V/3000 mAh |
| Operating temperature | -10°C to + 45°C |
| Working mode | monoband/dualband |
| Modulation | F3E(FM) |
| Max. frequency deviation | ≤ ±5KHz |
| Spurious radiation | < -60dB |
| Frequency stability | ±2.5 ppm |
| Rx sensitivity | < 0.2uV |
| Audio output power | ≥ 500mW |
| Dimensions | 64x121x35mm (LxAxP) |
| Weight | 240g |
Specifications are subject to change without notice.
WARNING. Direct plug-in ac/dc power supply must be used for disconnecting the transceiver from the mains; the desktop charger must be positioned close to the unit and easily accessible.
9. User Tips
- Optimize Battery Life: For best battery performance, fully charge and discharge the battery two to three times upon initial use. When storing the battery for extended periods, ensure it is approximately 80% discharged.
- Clear Communication: When transmitting, keep the microphone 2.5 cm to 5 cm from your mouth for optimal reception volume.
- Keypad Lock: Utilize the keypad lock feature (long press '*') to prevent accidental key presses during active use or when carrying the radio.
- Menu Navigation: Familiarize yourself with both arrow key navigation and numerical shortcuts for quicker access to menu settings.
- NOAA Weather: For users in the USA and Canada, regularly check NOAA Weather Radio for important weather alerts by accessing the Weather Radio function via the [OSQL] key.
10. Warranty and Support
The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation, and dissemination of this handbook may be made in any form without prior written authorization.
For technical support or further inquiries, please contact XHDATA:
- Skype: radiwow
- TikTok: XHDATAradio
- YouTube: Xhdata Radio
- Facebook: Xhdata Radios
- Web: www.xhdata.com.cn
- Whatsapp: +86 18025193267
- E-mail: xhdatacn@gmail.com
A user manual (PDF) is also available for download: XHDATA E100 User Manual (PDF)