Estardyn 1.9 Inch IPS Full Angle TFT

Contents

Estardyn 1.9 Inch IPS TFT Display Module User Manual

Model: 1.9 Inch IPS Full Angle TFT

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of the Estardyn 1.9 Inch IPS Full Angle TFT Display Module. This high-definition color display module features a 170x320 resolution and utilizes an SPI serial port for communication, making it suitable for a wide range of embedded applications.

Front and back view of the Estardyn 1.9 Inch IPS TFT Display Module, showing a sample image on the front and the FPC connector on the back.

Figure 1: Estardyn 1.9 Inch IPS TFT Display Module (Front and Back)

2. Specifications

The following table outlines the key specifications of the Estardyn 1.9 Inch IPS Full Angle TFT Display Module:

FeatureDescription
Brand NameEstardyn
Model Number1.9 Inch IPS Full Angle TFT
TypeTFT
Display Mode170x320
Resolution170x320
Driver ICST7789
InterfaceSPI Serial Port
Logic Voltage (VCC)3.3V
Backlight Voltage (VLED)3.3V
Backlight Current (ILED)20mA
Operating Temperature-20°C to 70°C
Storage Temperature-30°C to 80°C
Display DirectionFull View
Outline Dimensions25.80 x 47.72 mm
Active Area23.70 x 42.72 mm
High-concerned chemicalNone
CustomizationYes
Technical drawing of the Estardyn 1.9 Inch IPS TFT Display Module, showing detailed dimensions, pinout, and electrical characteristics.

Figure 2: Technical Drawing with Dimensions and Pinout

3. Setup and Connection

This display module communicates via an SPI serial interface. Proper connection to your microcontroller or development board is essential for correct functionality. Refer to the pinout diagram and table below for connection details.

3.1 Pinout Description

Pin No.SymbolDescription
1GNDGround
2VCCPower Supply (3.3V)
3SCLSPI Clock Line
4SDASPI Data Line
5RESReset Pin
6DCData/Command Selection Pin
7CSChip Select Pin
8BLKBacklight Control Pin

3.2 Connection Procedure

  1. Ensure your microcontroller operates at 3.3V logic levels. If not, use appropriate level shifters.
  2. Connect the GND pin of the display module to the ground of your system.
  3. Connect the VCC pin to a stable 3.3V power supply.
  4. Connect the SCL, SDA, RES, DC, CS, and BLK pins to the corresponding GPIO pins on your microcontroller, as defined by your chosen SPI library or custom implementation.
  5. Double-check all connections before applying power to prevent damage.
Back view of the Estardyn 1.9 Inch IPS TFT Display Module, clearly showing the FPC connector and pin labels for connection.

Figure 3: Display Module Back View with Pin Labels

4. Operating Instructions

To operate the Estardyn 1.9 Inch IPS TFT Display Module, you will need to implement a software driver for the ST7789 controller via the SPI interface. Many open-source libraries are available for popular microcontrollers (e.g., Arduino, ESP32, Raspberry Pi) that support the ST7789 driver.

4.1 Basic Operation Sequence

  1. Initialization: After power-up, the display controller (ST7789) needs to be initialized by sending a sequence of commands. This typically involves resetting the display, setting display parameters (e.g., pixel format, gamma correction), and turning on the display.
  2. Data Transfer: To display images or text, pixel data is sent to the display's GRAM (Graphics RAM) via the SPI interface. The DC pin is used to differentiate between command and data bytes.
  3. Backlight Control: The BLK pin can be used to control the backlight. Driving it high typically turns the backlight on, and low turns it off. PWM can be used for brightness control if supported by your microcontroller.

Consult the ST7789 datasheet for detailed command sets and timing diagrams for advanced control.

5. Maintenance

The Estardyn 1.9 Inch IPS TFT Display Module is a robust electronic component, but proper care ensures its longevity and performance.

  • Cleaning: Use a soft, lint-free cloth, slightly dampened with distilled water or an electronics-safe cleaning solution, to gently wipe the display surface. Avoid abrasive materials or harsh chemicals.
  • Handling: Always handle the module by its edges to avoid touching the display area or the flexible flat cable (FPC). Static electricity can damage electronic components, so use anti-static precautions when handling.
  • Storage: Store the module in a dry, cool environment within the specified storage temperature range (-30°C to 80°C). Protect it from direct sunlight and excessive humidity.
  • Power Supply: Ensure a stable 3.3V power supply is used. Voltage fluctuations or overvoltage can damage the display controller.

6. Troubleshooting

If you encounter issues with your display module, consider the following troubleshooting steps:

  • No Display/Blank Screen:
    • Verify all power connections (VCC, GND) are correct and stable at 3.3V.
    • Check all SPI data lines (SCL, SDA, RES, DC, CS) for proper connection and continuity.
    • Ensure the backlight (BLK) pin is driven high or appropriately controlled.
    • Confirm your software initialization sequence for the ST7789 controller is correct.
  • Incorrect Colors/Garbled Display:
    • Check the SPI data rate. Some microcontrollers might require specific clock speeds for stable communication.
    • Verify the pixel format and color depth settings in your software match the display's capabilities.
    • Ensure the data transfer order (MSB/LSB first) is correct for your SPI setup.
  • Partial Display/Missing Pixels:
    • Inspect the FPC connector for proper seating and any damage.
    • Review your display buffer and drawing routines for off-by-one errors or incorrect addressing.

7. User Tips

  • Software Libraries: For ease of development, consider using established open-source libraries like Adafruit_GFX and Adafruit_ST7789 for Arduino-compatible platforms. These libraries abstract much of the low-level control.
  • Power Consumption: While the display is low power, consider controlling the backlight (BLK pin) to conserve energy in battery-powered applications.
  • Prototyping: When prototyping, use a breadboard and jumper wires for initial connections. Once functionality is confirmed, consider a custom PCB or more robust wiring for permanent installations.

8. Warranty and Support

For any technical assistance, warranty inquiries, or support related to your Estardyn 1.9 Inch IPS TFT Display Module, please contact the Estardyn Flagship Store directly. Ensure you provide your purchase details and a clear description of the issue for prompt assistance.

© 2024 Estardyn. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.