1. Product Overview
This Scimagic-RC remote control is a compatible replacement transmitter designed for use with TELECO TXP-433-A01, TXP-433-A02, and TXP-433-A04 garage door and gate openers. It operates on a 433MHz/433.92MHz rolling code frequency, ensuring secure and reliable operation. The remote is available in 1-key, 2-key, and 4-key configurations to suit various needs.
Figure 1: Available remote control configurations (1-key, 2-key, 4-key)
2. Specifications
| Feature | Specification |
|---|---|
| Product Material | ABS |
| Product Weight | 50 g |
| Number of Channels | 1, 2, or 4 (depending on model) |
| Battery | 3V CR2032 (Included) |
| Installation | Wireless |
| Code Type | Rolling Code |
| Frequency | 433MHz, 433.92MHz |
| Radio Transmission Distance | 20-100m (Open area) |
| Programming Type | Programming with the motor (receiver) |
Figure 2: Remote control and wall mount base dimensions
3. Compatibility
This remote control is 100% compatible with the following TELECO models:
- TELECO TXP-433-A01
- TELECO TXP-433-A02
- TELECO TXP-433-A04
Figure 3: Compatible TELECO remote models
Important Note:
This remote control is NOT compatible with TELECO TVTXP 868MHz (grey shell) models.
Figure 4: Incompatible TELECO TVTXP 868MHz models
4. Package Contents
Your package includes:
- Remote Control (1, 2, or 4 key version)
- CR2032 Battery
- Keychain
- Clip
- English Manual
5. Setup (Programming)
Prerequisite: You must have physical access to the motor (receiver) of your garage door or gate opener to perform programming. If you do not have access to the motor, this remote control cannot be programmed.
Follow these steps to program your new remote control:
- Access the Motor: Locate the programming or 'Learn' button on your garage door or gate motor (receiver).
- Initiate Programming: Press the programming button on your motor. The LED indicator on the motor will illuminate, indicating it is in programming mode.
- Program Remote: Within a few seconds, press the desired button on your new remote control.
- Confirmation: The opener light on your motor will flash, confirming successful programming. The remote control is now ready for use.
To erase all codes from the receiver: Hold the receiver's 'Learn' button until the indicator light goes off (typically after 30 seconds). All previously learned codes will be erased from the receiver.
6. Operating Instructions
Once programmed, operate your garage door or gate by simply pressing the corresponding button on the remote control. The remote control is designed for ease of use and portability.
Figure 5: Operating the remote control
The remote control comes with a convenient wall-mount base, allowing you to store it securely and accessibly near your garage or gate entrance.
Video 1: Demonstrating the remote control and its wall-mount base assembly.
Figure 6: Remote control with its wall-mount base
7. Maintenance
Battery Replacement: The remote control uses a CR2032 3V battery. When the remote's range decreases or it stops responding, it's likely time to replace the battery.
- Gently pry open the remote control casing.
- Remove the old CR2032 battery.
- Insert a new CR2032 battery, ensuring correct polarity (+ side up).
- Close the remote control casing securely.
Figure 7: Battery replacement steps
General Care: Keep the remote control dry and clean. Avoid exposing it to extreme temperatures, direct sunlight, or harsh chemicals. Do not drop or subject the remote to strong impacts.
8. Troubleshooting
- Remote not responding: Check the battery. Replace it if necessary (refer to Section 7).
- Remote has reduced range: This often indicates a low battery. Replace the CR2032 battery.
- Remote cannot be programmed: Ensure you have physical access to the motor (receiver) and are following the programming steps correctly (refer to Section 5). Verify that your motor is one of the compatible TELECO TXP-433 series models.
- Remote is not compatible: Confirm your original remote is not a TELECO TVTXP 868MHz (grey shell) model, as this product is not compatible with 868MHz systems.
- Accidental operation or security concerns: If you suspect unauthorized access or wish to reset your system, erase all codes from your receiver (refer to Section 5).
9. User Tips
- For optimal performance, ensure a clear line of sight between the remote control and the receiver when operating.
- Consider mounting the remote control in its provided base near your garage or gate for easy access and to prevent misplacement.
- Always keep spare CR2032 batteries on hand for quick replacement.
- If you have multiple garage doors or gates, consider using a 4-key remote to control all of them from a single device, provided they are compatible TELECO TXP-433 series models.
10. Warranty and Support
For any questions, technical assistance, or support regarding this product, please contact the seller directly. Ensure you provide your product model information for faster service.
Disclaimer: Scimagic-RC distributes remote controls which are compatible with the door or garage motors and receivers produced by other manufacturers, and which are substitutes for remote controls produced by those manufacturers. All brand names, trademarks and registered trademarks are the property of their legal owners and are used here only for the description or identification of the devices. Except where a product is expressly stated to be a "genuine" remote, our remote controls are not produced by, and are not authorised, endorsed or approved by these other manufacturers.
