1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your MAXKGO Mini 6.8 100A Electronic Speed Controller (ESC). The MAXKGO Mini 6.8 is a high-performance, programmable brushless motor controller based on the VESC6 platform, designed for various electric vehicles and robotics applications.
Please read this manual thoroughly before using the product to ensure safe and optimal performance.
2. Safety Information
- Always disconnect power before making any connections or disconnections.
- Ensure all wiring is correct and secure to prevent short circuits or damage.
- Operate within the specified voltage and current limits to avoid overheating and component failure.
- Keep the ESC away from water, moisture, and extreme temperatures.
- Handle with care to avoid static discharge, which can damage electronic components.
- Voltage spikes must not exceed 60V.
3. Package Contents
Upon opening your MAXKGO Mini 6.8 100A ESC package, you should find the following items:
- MAXKGO Mini 6.8 100A ESC unit
- USB-C cable for programming
- Various connection cables (e.g., PPM, CAN, UART)

4. Specifications
| Feature | Detail |
|---|---|
| Brand Name | SEQURE (MAXKGO) |
| Firmware | 5.2 (supporting firmware upgrade) |
| Continuous Current | 100A |
| Instantaneous Current | 150A |
| Voltage Range | 14V-60V (4-13S LiPo, safe for 4S to 12S; voltage spikes may not exceed 60V) |
| BEC Output | 5V@1.5A |
| ERPM | 150000 |
| Hall Sensor Support | No, Sensorless operation |
| Supported Modes | BLDC, FOC (sinusoidal) |
| Control Interface Ports | USB, CAN, UART, IIC |
| Input Set Support | PPM, ADC, NRF, UART |
| Regenerative Capacity | Yes |
| Programmable | Yes |
| Motor Wire Gauge | 10AWG |
| Power Cable Gauge | 8AWG |
| Dimensions (incl. heatsink) | 64mm x 43.5mm x 34.7mm |

5. Key Features
- VESC6 Based: Fully compatible with VESC_TOOL for programming and real-time data monitoring.
- High-Performance CPU: Equipped with STM32F405 ARM Cortex-M4 CPU for fast and efficient processing.
- Multiple Control Modes: Supports Current, Dutycycle, and Speed control modes.
- Comprehensive Protection: Includes low voltage, high voltage, over-current, abnormal temperature, and MOSFET over-temperature protection.
- IMU Module Support: Can connect IMU modules (e.g., MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160) via IIC interface for balancing applications.
6. Setup and Wiring
Careful wiring is essential for the proper and safe operation of the MAXKGO Mini 6.8 ESC. Refer to the wiring diagram below for connections.

6.1 Connection Points Overview:
- Motor: Connect the three motor phase wires (typically A, B, C) to the corresponding outputs on the ESC. The ESC uses 10AWG motor wires.
- Battery: Connect the main power cable (8AWG) from your battery pack to the ESC's power input. Ensure correct polarity (red for positive, black for negative).
- USB: Use the provided USB-C cable to connect the ESC to a computer for configuration via VESC_TOOL.
- CAN: Connect to other VESC-compatible devices for multi-ESC setups or communication.
- PPM: For connecting a standard RC receiver (PWM signal).
- COMM: General communication port, includes ADC, TX, RX, GND, 3.3V, 5V pins. Useful for connecting external sensors or microcontrollers.
6.2 Initial Power-Up:
- Ensure all connections are secure and correct.
- Connect the ESC to your computer via the USB cable.
- Launch the VESC_TOOL software.
- Carefully connect the battery to the ESC.
- Follow the motor detection and configuration wizard in VESC_TOOL to set up your motor parameters.
7. Operating Instructions
The MAXKGO Mini 6.8 ESC is highly configurable using the VESC_TOOL software. This section outlines general operating principles.
7.1 VESC_TOOL Software:
The VESC_TOOL is the primary interface for configuring and monitoring your ESC. It allows you to:
- Perform motor detection and calibration.
- Set up control modes (Current, Dutycycle, Speed).
- Configure input devices (PPM, ADC, UART).
- Adjust protection thresholds (voltage, current, temperature).
- Monitor real-time data such as motor RPM, current, voltage, and temperature.
- Upgrade firmware (Firmware 5.2 and above supported).
For detailed instructions on using VESC_TOOL, please refer to the official VESC project documentation or community resources. A firmware download link is provided by the manufacturer:
7.2 Control Modes:
- Current Control: Motor current is directly controlled by the input signal. Ideal for applications requiring precise torque control.
- Dutycycle Control: The duty cycle of the PWM signal to the motor is controlled. This is a basic speed control method.
- Speed Control (FOC/BLDC): The ESC attempts to maintain a target motor speed. FOC (Field-Oriented Control) offers smoother and more efficient operation than BLDC (Block Commutation).
7.3 Regenerative Braking:
The ESC supports regenerative braking, which converts kinetic energy back into electrical energy to recharge the battery during braking. This feature can be configured in VESC_TOOL.
7.4 Test Video:
A test video demonstrating the ESC's functionality is available:
Video 1: MAXKGO Mini 6.8 ESC Test Demonstration. View it here: https://www.youtube.com/watch?v=fsVSe5GBb6M
8. User Tips
- Heatsink Management: The ESC includes a heatsink for thermal management. Ensure adequate airflow around the ESC, especially during high-current operation, to prevent overheating.
- Firmware Updates: Regularly check for and apply firmware updates using VESC_TOOL to benefit from performance improvements and bug fixes.
- Cable Management: Secure all cables to prevent them from vibrating loose or interfering with moving parts.
- Initial Configuration: Take your time during the initial VESC_TOOL setup. Incorrect motor parameters can lead to inefficient operation or damage.
9. Troubleshooting
This section provides solutions to common issues you might encounter.
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor not spinning or erratic behavior | Incorrect motor detection/configuration in VESC_TOOL; loose motor phase wires; Hall sensor issue (if applicable, though this ESC is sensorless). | Re-run motor detection in VESC_TOOL. Check all motor wire connections. Ensure correct input signal setup. |
| ESC overheating | Excessive current draw; insufficient cooling; incorrect motor parameters. | Reduce load or current limits. Improve airflow around the ESC. Verify motor parameters in VESC_TOOL. Check for short circuits. |
| No power to ESC | Battery not connected; incorrect battery polarity; faulty battery or power cable. | Check battery connection and polarity. Test battery voltage. Inspect power cables for damage. |
| Cannot connect to VESC_TOOL | USB cable issue; incorrect COM port selected; ESC not powered; driver issues. | Try a different USB cable. Ensure ESC is powered. Select the correct COM port in VESC_TOOL. Install necessary USB drivers. |
If you encounter issues not covered here, please consult online VESC communities or contact technical support.
10. Applications
The MAXKGO Mini 6.8 100A ESC is versatile and suitable for a wide range of applications requiring precise brushless motor control. Common uses include:
- Electric scooters
- Electric skateboards
- Electric bicycles
- Electric unicycles
- Go-karts
- Solar street lights
- Sightseeing cars
- Electric tricycles
- Handling forklifts
- Consumer robots

11. Warranty and Support
For warranty information and technical support, please refer to the manufacturer's official website or contact your retailer. Keep your proof of purchase for any warranty claims.