HamGeek ATS200

Contents

HamGeek ATS200 Full Band Radio Receiver User Manual

Model: ATS200

1. Introduction

The ATS200 is an advanced full-band radio receiver, designed as an upgraded version of the ATS120. It features a built-in frequency converter module, enabling reception up to 200MHz AM signals, including the 118-137MHz aviation band. This portable radio utilizes a SI4732+ESP32+Bluetooth+2.4-inch touch display solution, housed in a custom-designed aluminum alloy casing. It includes a 40MM large speaker and supports multiple reception modes: FM, AM, LSB, and USB. The FM mode incorporates RDS functionality, and Bluetooth stereo audio transmission (FM) allows for high-fidelity listening with Bluetooth earphones. An LNA preamplifier is integrated for flexible switching, optimizing performance across various signal conditions. Its slim, ultra-thin design, combined with an 820MM ultra-long telescopic antenna, makes it highly portable for travel.

HamGeek ATS200 Full Band Radio Receiver with USB-C cable and wrist strap
Figure 1: ATS200 Radio Receiver and included accessories.

2. Safety Warnings

Before using this product, please read and comply with all safety instructions to ensure safe operation and prevent damage.

2.1 Electrical Safety

  • Use only the power adapter provided with the product or a compliant power supply.
  • Do not use the device in humid environments unless explicitly stated as waterproof. The ATS200 is not water resistant.
  • If the power cord is damaged, discontinue use immediately and contact support for a replacement.
  • Always disconnect the power before cleaning the device.

2.2 Usage Environment

  • Operating temperature range: -10°C to 40°C (subject to model specifications).
  • Avoid direct sunlight, high temperatures, and dusty environments.
  • Ensure good ventilation and do not block heat dissipation holes.

2.3 Operational Safety

  • Do not disassemble or modify the product yourself. There are no user-repairable parts inside.
  • Prevent liquid from entering the product interior.
  • If the product emits smoke, unusual odors, or abnormal noise, immediately disconnect power and contact after-sales service.

3. Setup

3.1 Charging the Device

The ATS200 is equipped with a built-in 3.7V/1200mA high-capacity lithium battery. To charge, connect the device to a power source using the provided universal Type-C USB cable. The charging indicator will typically illuminate during charging and change status when fully charged.

3.2 Antenna Connections

  • Built-in Antenna: The radio features an 820mm ultra-long telescopic rod antenna for general reception. Extend it fully for optimal performance.
  • External Antenna: A 3.5MM external antenna interface is located at the bottom of the device, allowing connection to various outdoor antennas for enhanced reception.
  • FM Headphone Antenna: When using the 3.5MM stereo headphone output at the top, the headphone cable can also function as an antenna for FM mode.

4. Operating Instructions

4.1 Basic Controls

The ATS200 features a 2.4-inch TFT color touch screen and several physical buttons for control. Refer to the diagram below for button identification and functions.

ATS200 radio front view with screen and labeled buttons for power, screen lock, LNA, and Bluetooth pairing
Figure 2: Front panel controls and their functions.
  • Power Button (Top Left):
    • Long Press (3 seconds): Turns the device ON or OFF.
    • Short Press: Turns the mini LED flashlight ON or OFF.
  • Multi-function Button (Middle Left, below screen):
    • Short Press: Locks or unlocks the screen (indicated by "TL" character on screen).
    • Double Click: Turns the built-in LNA amplifier ON or OFF (indicated by "LNA" character on screen).
    • Long Press (3 seconds): Locks or unlocks the encoder knob (indicated by "RL" character on screen).
  • Bluetooth Pairing Button (Middle Right, below screen):
    • Short Press: Clears Bluetooth pairing.
  • Encoder Knob (Top Right): High-precision rotary knob for tuning and menu navigation.

4.2 Main Interface Menu Description

The touch screen interface provides access to various functions. The following are common menu options:

  1. HAM: Selects common amateur radio bands, including Single Sideband (SSB).
  2. BAND: Selects common radio broadcast bands.
  3. FREQ: Allows direct frequency input.
  4. BFO: Adjusts Beat Frequency Oscillator for SSB fine-tuning.
  5. STEP: Sets the tuning step size.
  6. BANDW: Selects the bandwidth.
  7. AGC: Controls Automatic Gain Control.
  8. ATT: Selects attenuation level.
  9. MODE: Selects the reception mode (e.g., AM, FM, LSB, USB).
  10. MUTE: Mutes the audio output.
  11. VOL: Adjusts the volume.
  12. NEXT: Navigates to the next page of menu options.

4.3 Frequency Ranges

The ATS200 supports a wide range of frequencies:

  • FM: 64-108MHz (with RDS function)
  • LW (Longwave): 153kHz - 500kHz
  • MW (Mediumwave): 520kHz - 1710kHz
  • SW (Shortwave): 1730kHz - 30000kHz
  • SSB (Single Sideband): 1730kHz - 30000kHz
  • AM (Extended Frequency): 1-200MHz
  • AIR (Aviation Band): 118-138MHz

Note: The aviation band does not support channel storage.

4.4 Bluetooth Operation

The ATS200 features built-in Bluetooth 5.3 for high-fidelity stereo audio transmission. You can connect Bluetooth earphones for private listening or share audio with other Bluetooth speakers. To clear existing pairings, short press the Bluetooth Pairing Button (Middle Right).

5. Maintenance

5.1 Cleaning

Always disconnect the power supply before cleaning the device. Use a soft, dry cloth to wipe the exterior. Do not use liquid cleaners or abrasive materials.

5.2 Storage and General Care

  • Store the radio in a cool, dry place, away from direct sunlight and high temperatures.
  • Avoid dusty environments to prevent internal component damage.
  • Ensure proper ventilation around the device and do not block any heat dissipation holes during operation or storage.
  • Prevent any liquids from entering the product interior.

6. Troubleshooting

  • Device not powering on: Ensure the battery is charged. Long press the power button for 3 seconds.
  • No audio: Check the volume level (VOL setting) and ensure the device is not muted (MUTE setting). Verify headphone connection if applicable.
  • Poor reception: Extend the telescopic antenna fully. If using an external antenna, ensure it is properly connected. Adjust BANDW (bandwidth) and ATT (attenuation) settings. Consider using the LNA amplifier if signals are weak.
  • Unusual operation (smoke, odors, noise): Immediately disconnect the power supply and contact after-sales service. Do not attempt to repair the device yourself.
  • Firmware issues: The ATS200 uses a new program that is incompatible with Russian firmware. Do not attempt to flash the device with unauthorized firmware, as this will damage the radio.

7. Specifications

Feature Specification
Model Number ATS200
Dimensions (W x H x D) 120 x 20 x 50mm
Screen 2.4-inch TFT Color Touch Screen
Audio Output Mode Mono (via built-in speaker), Stereo (via 3.5mm headphone jack)
Speaker Built-in 40MM large-sized speaker
Antenna Built-in 820mm telescopic rod antenna, 3.5mm external antenna interface
Power Supply Rechargeable Battery Pack (Built-in 3.7V/1200mA Lithium Battery)
Charging Interface Universal Type-C
Bluetooth Built-in Bluetooth 5.3 (High-fidelity stereo audio transmission)
Water Resistance Level Not water resistant
Enclosure Material High precision CNC aluminum alloy
Operating Temperature -10°C to 40°C
Reception Modes FM (with RDS), AM, LSB, USB
Frequency Ranges FM: 64-108MHz, LW: 153-500kHz, MW: 520-1710kHz, SW: 1730-30000kHz, SSB: 1730-30000kHz, AM: 1-200MHz, AIR: 118-138MHz

8. User Tips

Based on user feedback, here are some general tips:

  • Ensure you have received the correct model (ATS200) upon delivery to avoid confusion with similar models like ATS120 Pro.
  • For optimal reception, especially on shortwave and aviation bands, experiment with antenna positioning and consider using a dedicated outdoor antenna connected to the 3.5mm external antenna interface.
  • Familiarize yourself with the screen lock and encoder knob lock functions to prevent accidental changes during portable use.

9. Warranty and Support

9.1 Warranty Policy

This product typically comes with a 12/24-month warranty from the date of purchase. Please refer to the specific store announcement or your purchase documentation for exact warranty terms and conditions.

9.2 Technical Support

For detailed technical documentation, calibration certificates, or hard copies of the manual, please contact the seller via AliExpress internal message or email:

A user manual in PDF format is also available for download: ATS200 User Manual (PDF).

10. Disclaimer

This instruction manual is a general version. The actual product functions and parameters shall prevail. The manufacturer reserves the right to change product designs and specifications without prior notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.