1. Product Overview
The Kunray MXUS XF08 is a high-efficiency, low-noise brushless gear hub motor designed for electric bicycle conversion kits. It offers stable performance and a long service life, suitable for powerful adult mountain e-bike conversions and DIY projects.
Product Information
| Product Name | MOTOR |
|---|---|
| Model | MXUS-XF08 (Rear) |
| Manufacturer | Yangzhou Xintu Technology Co., Ltd |
| Origin | Mainland China |


2. Safety & Warnings
- Controller Compatibility: Ensure the controller you are using is a brushless controller with Hall sensor version.
- Self-Learning Function: Verify that your controller has a self-learning function.
- Temperature Warning: Do not touch the device when it is operating, as its temperature can be high, potentially causing harm.
- Intended Use: This device is designed for off-road use. It is not intended for use on public roads. Please ensure compliance with all local regulations regarding e-bike modifications.
- Fire Risk: Please mind potential fire risk and strictly follow the instruction manual for charging and storage of associated battery components (not included).
3. Setup & Installation
This section provides detailed instructions for installing the MXUS XF08 motor and its accessories. Please refer to the wiring diagrams and illustrations carefully.
3.1 Motor Installation
The motor is designed for rear wheel installation. The dropout/open size required is 135-142mm.
- Gasket and Screw Installation:
- If your bike's opening size is larger than the standard, install the spacer on the inside of the rear fork.
- If your bike's opening size is equal to the standard, install the spacer on the outside of the rear fork.
- Wheel Size Compatibility: The motor is compatible with wheel sizes from 16 to 28 inches. Ensure your tire size matches the motor's intended use.
- Fork Compatibility:
- Front Fork Open Size: 100-110mm.
- Rear Fork Open Size: 135-142mm.
- If the difference between the rear drive and the open gear is 10mm, you can use a car jack to widen it slightly without affecting the safety of the original car.



3.2 Wiring Connection
The motor comes with either a normal wire connector or a waterproof wire connector. Ensure you connect the controller according to the specific wiring diagram provided in the product details or the general instructions below.

4. Operating Instructions
This section covers the installation and basic operation of the display, throttle, E-brake, and PAS components.
4.1 Display Installation (SM Plug)
- Break off the extension seat buckle and insert it from a low position.
- Align the position and clamp the display head in place. Adjust the angle to align the position.
- Adjust the angle and tighten the screws. The display installation is complete.
The display connects to the controller via a 5-pin SM plug. SM Line length: 1650mm/64.96inch.
4.2 Throttle Installation (SM Plug)
- Loosen the screws on the throttle.
- Slide the throttle onto the handlebar.
- Tighten the screws to secure the throttle.
The throttle connects to the controller via a 3-pin SM plug. SM Line length: 1800mm/70.86inch.
4.3 E-Brake Lever / Sensor Installation (SM Plug)
The E-Brake lever and sensor connect to the controller via 2-pin SM plugs.
E-Brake Sensor Installation:
- Loosen the screws on your existing brake lever.
- Remove the pedal (if necessary for access).
- Install the E-Brake sensor.
- Ensure the magnet and sensor are within 5mm distance for proper function.
4.4 PAS (Pedal Assist System) Installation (SM Plug)
The PAS sensor connects to the controller via a 3-pin SM plug. Ensure the sensor magnet distance is appropriate (typically close proximity for activation).


5. Maintenance
The MXUS XF08 brushless gear motor is designed for durability and low maintenance. Its fully sealed design provides IP65 level protection, making it highly waterproof and rust-proof.
- Cleaning: Regularly clean the exterior of the motor to prevent dirt buildup. Use a damp cloth; avoid high-pressure water jets directly on electrical connections.
- Inspection: Periodically check all connections and mounting bolts for tightness. Ensure no wires are frayed or damaged.
- Storage: When not in use for extended periods, store the motor in a dry, cool place.

6. Troubleshooting
If your motor is not functioning as expected, please follow these troubleshooting steps:
- Controller Compatibility: Ensure your motor is compatible with your specific controller model. The motor requires a brushless controller with a Hall sensor version and a self-learning function.
- Wiring Check: Verify that all wiring connections are correct and secure. Ensure the phase wires match correctly.
- Battery Voltage: Confirm that the voltage of your battery matches the rated voltage of the motor (e.g., 24V, 36V, or 48V).
- Physical Damage: Inspect the motor and associated components for any visible damage.
- Contact Support: If the issue persists after checking the above, please contact our after-sales team for assistance.
7. Specifications
Detailed technical specifications for the MXUS XF08 Brushless Gear Hub Motor:
| Parameter | 250W Version | 350W Version |
|---|---|---|
| Model | MXUS-XF08 | |
| Rated Voltage (V) | 24V/36V/48V | 36V/48V |
| Rated Power (W) | 250W | 350W |
| Wheel Size (inch) | 16" – 28" | |
| Rated Speed (km/h) | 25-28km/h | |
| Spoke | 36 hole spoke | |
| Position | Rear Wheel | |
| Dropout/Open Size | 135mm (135-142mm compatible) | |
| Magnet Poles (2p) | 10 | |
| Brake Type | V/Disk Brake | |
| Freewheel | 6S-9S | |
| Operating Temperature | -20 to 45℃ | |
| Efficiency (%) | ≥78% | |
| Noise Grade (DB) | <55 | |
| IP Grade | IP65 | |
| Salt Spray Test Standard (h) | 96 | |


8. Warranty & Support
We are committed to providing high-quality products and support.
- Accessories Warranty: Accessories have a three-month warranty period for quality problems, with free replacement.
- Motor Warranty: The motor itself has a one-year warranty period.
- Transit Damage: If the product is damaged or parts are lost in transit, we will take full responsibility.
Contact Information
For any questions or support needs, please contact our after-sales team:
- Email: salemanager@cnkunray.com
- Manufacturer Address: Rm901, 9th floor, yifeng entrepreneurship park, yangzhoucityjiangsu
Please feel free to contact customer service if you have any questions. Customer service will help you solve the problem.
A user manual (PDF) is also available for download: View User Manual (PDF)
9. User Tips
- Always double-check the voltage compatibility between your motor and battery to prevent damage.
- If you are unsure about any installation steps, especially wiring, do not hesitate to contact customer service for guidance.
- Regular maintenance, such as checking connections and cleaning, can significantly extend the life and performance of your motor.