1. Introduction
Preface
Thank you very much for choosing our Multi-Band Amateur Radio. This radio utilizes the latest advanced technology to provide reliable communications in today's demanding environments. It is extremely stable and reliable for long-distance communication with a sleek and compact design.
It features emergency alarm, personnel death alarm, work alone, GPS, APRS position reporting, analog DTMF, 2TONE, 5TONE, CTCSS/DCS encode/decode. Whether you are a professional who needs to keep in touch with your active team (such as ranching, farming, driving, hunting, forest protection, tactical training) or a recreational user who just wants to keep in touch with friends and family, this product will surely bring you all kinds of convenience in your work, life and leisure.
To avoid personal injury or property damage caused by improper operation, please read all information carefully before using our products. To ensure that you maximize the convenience of this product, please read this manual and the Safety Information Manual before use.
1.2 Content of the Packaging
This transceiver comes shipped with the following items in the box:
- 1 Radio body
- 1 Lithium-Ion battery pack
- 1 Instruction Manual
- 1 Belt Clip
- 1 Desk charger (With wall-wart)
- 1 Antenna
- 1 Wrist Belt
* If any item is missing, please notify your Baofeng / Pofung dealer.
1.3 Features and Functions
- 1.77" TFT large screen, full keyboard, fully open menu operation
- Scanner function: VFO scan range setting, three scan recovery methods, channel scan, CTC/DCS scan, scan channel addition and removal
- Multi-band scanning receiver: 108-136, 136-174, 220-260, 350-390, 400-520MHz (Suitable for North American users)
- EU Frequencies: 144-146MHz, 430-440MHz (Applicable to users in EU countries and regions)
- Built-in input method, allows this device to edit channel name
- NOAA Weather Radio Channel Reception in the United States and Canada
- Frequency step, selectable between 2.5K | 5.0K | 6.25K | 10.0K | 12.5K | 20.0K | 25.0K | 50.0K
- Type-C direct charging and charging stand, more convenient battery life
- Dual-band handheld transceiver
- High Capacity Lithium-Ion battery (2500mAh)
- 50 CTCSS tones and 105 DCS codes
- 10 zones storage, Up to 640 named memory channels
- High or low power selectable (5W-10W)
- Function beep on the keyboard
- Programmable repeater offset
- Transmission time-out timer
- Busy channel lock out
- LED flashlight
- Ten (10) levels of Squelch adjustment
- End of transmission tone, aka “Roger Beep"
- Two (2) pins for Kenwood accessory port
- DTMF encoder and DTMF manual dial
- Broadcast FM radio receiver 87.5-108 MHz
- VOX (voice activated transmit)
- Alarm function
- Display illumination programmable via keypad
- Dual watch / Dual reception
- Battery saving function
- Scan mode
- Built in CTCSS/DCS tones
- PC programmable
- Cross band reception
- One touch search frequency
- Analog signaling DTMF, 2TONE, 5TONE, BDC1200 codecs
- GPS positioning function, location sharing and requesting location information from others
Video: Baofeng UV-5RH PRO Walkie Talkie Product Overview.
2. Safety Warnings and Regulations
2.1 FCC Regulatory Conformance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Verification of harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
2.2 Compliance with RF Exposure Standards
The radio complies with the following RF energy exposure standards and guidelines:
- United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093
- American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015
- Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition
2.3 RF Exposure Compliance and Control Guidelines
To control your exposure and ensure compliance with the occupational/controlled environmental exposure limits, always adhere to the following procedures.
Guidelines:
- Do not remove the RF Exposure Label from the device.
- User awareness instructions should accompany device when transferred to other users.
- Do not use this device if the operational requirements described herein are not met.
Operating Instructions:
- Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).
- Keep the radio unit at least 2.5cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes.
- When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/controlled environmental RF exposure limits.
- Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.
- Contact your local dealer for the product's optional accessories.
2.4 Precautions for Portable Terminals
Operating Prohibitions:
To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:
- Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials. In such location, only an approved Ex-protection model is allowed for use, but any attempt to assemble or disassemble it is strictly prohibited.
- Do not operate the product near or in any blasting area.
- Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate the product in any area where use of wireless communication equipment is completely prohibited.
Important Tips:
To help you make better use of the product, be sure to observe the following instructions:
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 centimeters away from your body during transmission.
- Do not keep the product receiving at high volume for a long time.
- For vehicles with an air bag, do not place the product in the area over the air bag or in the air bag deployment area.
- Keep the product and its accessories out of reach of children and pets.
- Please operate the product within the specified temperature range.
- Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at a proper location for cooling.
- Handle the product with care.
- Do not disassemble, modify or repair the product and its accessories without authorization.
2.5 Precautions for Batteries
Charging Prohibitions:
To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions:
- Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres and other flammable or explosive materials.
- Do not charge your battery that is wet. Please dry it with a soft and clean cloth prior to charge.
- Do not charge your battery suffering deformation, leakage and overheat.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location where strong radiation is present.
- Overcharge shall always be prohibited for it may shorten the life of your battery.
Maintenance Instructions:
To help your battery work normally or prolong its life, be sure to observe the following instructions:
- Accumulated dust on charging connector may affect normal charging. Please use a clean and dry cloth to wipe it on a regular basis.
- It is recommended to charge the battery under 5℃~40℃. Violation of the said limit may cause battery life reduction or even battery leakage.
- To charge a battery attached to the product, turn it off to ensure a full charge.
- Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
- Do not dispose of the battery in fire.
- Do not expose the battery to direct sunlight for a long time nor place it close to other heating sources.
- Do not squeeze and penetrate the battery, nor remove its housing.
Transportation Instructions:
- Damaged batteries must not be transported.
- To avoid short circuit, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
- The radio must be switched off and secured against switch-on, if the battery is attached.
The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for the local regulations and further information.
3. Product Overview
3.1 Buttons and Controls of the Radio

Image: Front, side, and top views of the Baofeng UV-5RH PRO, highlighting its various buttons and controls.
- Power/Volume knob
- SK1- Broadcast FM and Alarm key
- PTT key
- VFO/MR mode key
- Status LED
- SK2-Flashlight and Monitor key
- A / B select key
- Key (MENU)
- Numeric keypad
- Antenna jack
- LED flashlight
- Color LCD
- Accessory jack
- Speaker and microphone
- One-Touch search key
- Key (EXIT)
- Up or Down navigation keys
- Type-C charging port
- Type-C charging indicator
- Battery release latch
3.2 Main Keypad Controls
- VFO/MR: Short press to switch VFO/MR mode. Press and hold to switch channel display mode: Channel CH, Frequency (display small channel number), Name (channel alias).
- A/B: Short press to switch between A (upper) and B (lower) displays. Press and hold to switch Double Wait / Signal Wait / Off dual watch mode.
- Sweep: Short press to enter one key sweep.
- EXIT: Short press to return to the menu or return to the previous menu. Press and hold to quickly enter GPS mode (My Location, valid when GPS function is turned on).
- Lock/Unlock: Press and hold to lock or unlock the keyboard. In transit mode, short press the key in inverted frequency (display R)/offline (display T).
- DTMF Dial: Short press to enter DTMF dial. Press and hold to scan on and off.
- Weather Switch: Press and hold '0' to enter weather switch to select weather channel.
3.3 Programmed Key (SK1/SK2)
It is possible to set different functions for [SK1], [SK2] keys. You can configure these either via the radio Menu (Radio Setting – Press and Longpress SK1, SK2) or via PC software (Buttons).
| Option | Functionality |
|---|---|
| None | No function is assigned to this button. |
| Scan | To enable or disable the Scan feature. |
| Monitor | To enable or disable the Monitor feature. |
| Touch | To enable or disable the Touch feature. |
| FM Radio | To enable or disable the FM Radio feature. |
| SOS | To enable or disable the emergency alarm feature. |
| GNSS system | To enable or disable the GNSS system feature. |
| One Touch Search | To enable or disable the One Touch Search feature. |
| 1750Hz | Transmits 1750Hz Tone Burst |
3.4 Status Indications
The top LED will help you to identify the current radio status.
| LED Indication | What it Indicates |
|---|---|
| Constant Green | Receiving Signal |
| Constant Red | Transmitting signal |
| Flashes Green | Monitor mode/Scanning Receiving |
3.5 LCD Icon Summary

Image: A detailed view of the radio's 1.77-inch color LCD screen, illustrating various status icons and their corresponding functions.
- VOX enabled: Voice Operated Exchange is active.
- Man Down Enable: Man Down feature is active.
- APO Enable: Automatic Power Off is active.
- FM Radio Enable: FM Radio function is active.
- Battery level: Indicates current battery charge.
- Keyboard locked: Keypad is locked.
- Bluetooth enabled: Bluetooth function is active (Note: some users report this feature may not be present or functional).
- GPS enabled: GPS function is active.
- NOAA enabled: NOAA Weather Radio is active.
- NOAA Alerts Enabled: NOAA Weather Alerts are active.
- Current Zone: Displays the current operating zone.
- Watch Channel: Indicates the channel being monitored.
- Watch Frequency: Displays the frequency being monitored.
- A BAND RSSI: Received Signal Strength Indicator for Band A.
- A Band: Upper frequency band.
- VFO Mode: Variable Frequency Oscillator mode.
- Scan On: Scanner is active.
- Operating Frequency: Current operating frequency.
- B Band: Lower frequency band.
- Transmit power: Indicates the current transmit power level.
- Signal Wait: Indicates waiting for a signal.
- Volume level: Current audio output volume.
- Squelch level: Current squelch setting.
*The highlighted band is the main channel (i.e., the working band) and the grayed-out band is the sub band (the watch band).
4. Installation and Setup
Before the radio is ready for use, you need to attach the battery pack, as well as charge the battery.
4.1 Installing/Removing the Antenna
- Installing the Antenna: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
- Removing the Antenna: Turn the antenna counter-clockwise to remove it.
4.2 Installing the Belt Clip
- At the back of the radio there are two parallel screws mounted above the battery. Remove these and thread them through the holes on the belt clip as you screw them back into the radio body.
- Removing the Belt Clip: Unscrew counter-clockwise to remove the belt clip.
4.3 Installing the Battery Pack
Before attaching or removing the battery, make sure your radio is turned off by turning the power/volume knob all the way counter-clockwise.
- Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
- Once aligned with the guide-rails, slide the battery upward until you hear a click as the battery locks in place.
Removing the Battery Pack:
To remove the battery, press the battery release above the battery pack, as you slide the battery downward.
4.4 Installing the Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
Diagram: The internal manual shows a circuit diagram for the speaker/microphone connection, indicating a 2.5mm speaker jack and a 3.5mm microphone jack with PTT and +5V connections.
4.5 Charging the Battery Pack
The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/discharging the battery two or three times before the operating capacity will reach its best performance. The battery pack life may be depleted when its operating time decreases even though it has been fully and correctly charged. If this is the case, replace the battery pack.
Charger Supplied:
Please use the specified charger provided by our company. Other models may cause explosion and personal injury. After installing the battery pack, and if the radio displays low battery with a voice prompt, please charge the battery.
How to Charge:
- Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the charger. The indicator light blinks orange and is then ready to charge a battery.
- Plug the battery or the radio into the charger. Make sure the battery terminals are good in contact with charging terminals. The indicator light turns to red—charging begins.
- It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, the charging is completed. Remove the battery or the radio unit with its battery from socket.
When charging a radio (with battery) the indicating lamp will not turn into green to show the fully charged status if the radio is powered on. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is power-on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. So the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged.
LED Indicator (Charging Status):
| Status | LED |
|---|---|
| No Battery | Green and red alternately flashing |
| Charge Normally | Red |
| Fully Charged | Green |
| Trouble | Red blinks fast for a long time |
NOTE: Trouble means battery too warm, battery short-circuited or charger short-circuited.
How to Store the Battery:
- If the battery needs to be stored, keep it in status of 80% discharged.
- It should be kept in low temperature and dry environment.
- Keep it away from hot places and direct sunlight.
- Do not short circuit the battery terminals.
- Never attempt to remove the casing from the battery pack.
4.6 Using the Type-C USB Charger
The Type-C USB charger is a handy port that allows you to conveniently charge your Li-ion battery pack.
- Make sure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end of the micro-USB charger to wall power outlet.
- An empty battery will be fully charged in 4 hours.
- The battery meter on LCD will move to indicate the battery is charging.
Note:
- It is recommended to power OFF your radio while charging. However, if power is turned on while charging, you may not be able to transmit a message if the battery is completely empty. Allow time for the battery to charge to 1 bar before attempting to transmit a message.
- For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio while connected to the charger.
5. Basic Operations
5.1 Power On/Off the Radio
Turning the unit on:
To turn the unit on, simply rotate the Volume/Power knob clockwise until you hear a "click". If your radio powers on correctly there should be an audible double beep after about one second and the display will show a message or flash the LCD depending on settings for about one second. Then it will display a frequency or channel. If the Voice prompt is enabled, the voice will announce "frequency mode" or "channel mode".
Turning the unit off:
Turn the Volume/Power knob counter-clockwise all the way until you hear a "click". The unit is now off.
5.2 Adjusting the Volume
To turn up the volume, turn the Volume/Power knob clockwise. To turn the volume down, turn the Volume/Power knob counter-clockwise. Be careful not to turn it too far, as you may inadvertently turn your radio off.
5.3 Main Band/Sub Band Switch
Press the [A/B] key to switch between A (upper) and B (lower) displays. The frequency or channel on the selected display becomes the active listening and transmit frequency or channel.
NOTE: The highlighted band is the main band and the grey band is the sub band.
5.4 VFO/Channel Switch
Pressing the [VFO/MR] key switches between Frequency (VFO) Mode and Memory (MR) mode. Memory mode is sometimes also referred to as Channel mode.
For everyday use, Channel (MR) mode is going to be a whole lot more practical than Frequency (VFO) mode. However, Frequency (VFO) mode is very handy for experimentation out in the field. Ultimately which mode you end up using will depend entirely on your use case.
5.5 Frequency (VFO) Mode
In Frequency (VFO) mode you can navigate up and down the band by using the ▲ or ▼ keys. Each press will increment or decrement your frequency according to the frequency step you've set your transceiver to.
You can also input frequencies directly on your numeric keypad with kilohertz accuracy.
The following example assumes the use of a 12.5 kHz frequency step.
Example: Entering the frequency 436.61250 MHz on display A
- In standby mode, press and hold the [VFO/MR] key to switch to the frequency (VFO) mode.
- Enter [4][3][6][6][1][2][5][0] on the numeric keypad.
WARNING! Just because you can program in a channel does not mean you're automatically authorized to use that frequency. Transmitting on frequencies you're not authorized to operate on is illegal, and in most jurisdictions a serious offense. However, it is legal in most jurisdictions to listen. Contact your local regulatory body for further information on what laws, rules and regulations apply to your area.
5.6 Channel (MR) Mode and Channel Selection
Pressing the [VFO/MR] key switches between Frequency (VFO) Mode and Memory (MR) mode. Select Channel mode.
- Operation 1: Press the ▲ or ▼ navigation key to select the channel.
- Operation 2: Input the channel numbers by the keyboard. For example, if you want to switch to channel 12, input [1][2] (a total of 2 digits), and it will switch to channel 12.
When the voice prompt function is enabled, the corresponding channel will be broadcast by voice.
5.7 Select a Zone
A zone is a group of channels with the same property. The radio supports up to 10 zones, with a maximum of 64 channels per zone. To select a zone, do one of the following:
Press [MENU] key, go to Menu > Zone, press ▲ or ▼ navigation key to select a zone, and then press [MENU] key to switch to the selected zone. The corresponding regional alias will be displayed at the bottom of the screen.
5.8 Making a Call
NOTE: Press the [A/B] key to switch the main channel to the other channel if there are 2 channels shown on the display. In standby mode, press and hold the [VFO/MR] key to switch between frequency (VFO) mode and channel (MR) mode.
- Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. Making a call, the red LED is on.
- Frequency mode call: Press and hold the [VFO/MR] key to switch to the frequency mode, input the working frequency within the allowable frequency range, and press and hold the [PTT] key to transmit on the current frequency. Speak into the microphone with normal tone. Making a call, the red LED is on.
- Receive a call: When you release the [PTT] key, you can answer it without any action. When receiving a call, the green LED is on.
NOTE: To ensure the best reception volume, keep the distance between the microphone and the mouth at the time of transmission from 2.5 cm to 5 cm.
5.9 Emergency Alert
The Emergency Alert feature can be used to signal members in your group for help.
To activate the emergency alert function, Press the pre-programmed [Emergency Alarm] key.
Press the pre-programmed [Emergency Alarm] to exit the emergency alert function.
WARNING: The Emergency Alert feature should only be used in the event of an actual emergency.
5.10 FM Radio (FM)
Method 1: Press [MENU] key, go to main Menu -> Radio Settings -> Press/Longpress of "SK1/SK2" as [FM Radio], and turn on or off the radio by pressing the preset [FM Radio] key.
Method 2: Press [MENU] key, go to main Menu -> Radio Settings -> Radio On/Off, turn the radio on or off.
After turning on the radio function, the station search method is as follows:
- Press [#2] key to enter radio search mode, the screen displays 'Seeking...', the radio will automatically save the searched radio frequency as a radio channel (memory mode).
- Press ▲ or ▼ to select the radio channel.
- Directly input familiar radio frequency by numeric keys (frequency mode, e.g. 96.9MHz, input 969).
- Short press the preset [FM Radio] key or [EXIT] key to exit the radio mode.
The frequency ranges to listen to the radio is 65-108MHz. When listening to broadcast FM, press [A/B] key to switch between 65-75 MHz and 76-108 MHz band.
5.11 Radio Interrupt
- On: When FM radio is used, you can still receive or transmit on the channel.
- Off: When FM radio is used, the radio will not permit a transmission or reception.
5.12 Monitor
In standby, Press the pre-programmed [Monitor] key to enter Monitor. When receiving matched carrier but the signaling or the signal is too weak, this function allows monitoring the weak signal.
Press the pre-programmed [Monitor] key again to turn off the speaker and exit the Monitor mode.
5.13 Keypad Lock
The radio features a keypad lock that locks out all keys except for the three side keys.
To enable or disable the keypad lock, press and hold the [*] key for about two seconds.
You can also enable so that the radio automatically locks the keypad after ten seconds from the menu.
5.14 Frequency Reversal
A short momentary press of the [R] key enables the reverse function.
If you for some reason want to listen to the repeater's input frequency instead, press [R] key momentarily and you'll reverse your transmit and receive frequencies.
5.15 TX Repeaters Tone
Tone-burst 1750Hz, but also 1000Hz, 1450Hz, 2100Hz, these tone-bursts are mainly used for repeater activation and are more common in Europe.
Before using the Tone-burst function, the SK1/SK2 programmable key must be defined as the “1750Hz” function.
Press the pre-programmed [1750Hz] key to send 1750Hz tone-bursts. This function is useful for communications through repeaters.
5.16 NOAA Weather/Weather Alert
Your radio has a NOAA Weather Radio function, to enable the user to receive weather reports from designated NOAA stations. Your radio also has a NOAA Weather Scan function, to enable the user to scan all 10 channels of the NOAA Weather Radio.
Press [MENU] key >> NOAA weather >> Weather On/Off. Options:
- Off: NOAA weather forecast function is not enabled.
- WX1 162.550 MHz
- WX2 162.400 MHz
- WX3 162.475 MHz
- WX4 162.425 MHz
- WX5 162.450 MHz
- WX6 162.500 MHz
- WX7 162.525 MHz
- WX8 161.650 MHz
- WX9 161.775 MHz
- WX10 163.275 MHz
Press ▲ or ▼ to select a NOAA channel. Enable this channel and display the NOAA icon on the first line.
Note: Channels WX 1 through WX10 receive only NOAA and Canadian Weather Radio channels. You cannot transmit on these channels.
Weather Alert:
Press the [MENU] key >> NOAA Weather >> Weather Alert. Options:
- Off: Disables the Weather Alert function. The weather alert icon is not displayed.
- On: Enables the weather alert function. The weather alert icon is displayed.
With the Weather Alert feature enabled, the radio returns to standby and is allowed to receive calls. The radio guards the radio channel and weather channel and automatically cycles through the work channel and weather alert channel.
Activate the Weather Alert feature and receive a 1050 HZ alert signal, you will hear a loud beep and the radio will automatically switch to weather broadcast mode.
NOAA Weather Shortcuts:
In standby mode, press and hold [0] key to quickly enter the NOAA weather menu, press ▲ or ▼ key to select a weather channel or turn off NOAA weather.
Press the [MENU] key to Weather Alert, press ▲ or ▼ to select ON or OFF.
Press the [EXIT] key to return to the radio mode, the screen displays the NOAA icon.
5.17 One Touch Frequency Search
Method 1: Press [MENU] key, go to the main Menu -> Radio Settings -> Press/Longpress of "SK1/SK2" as [OneTouch Search], and enter the frequency search mode by pressing the preset [OneTouch Search] key.
Method 2: Press the [Green] key (green key, OneTouch Search) to enter the frequency search mode.
When using the OneTouch Search function, this unit will act as a receiver.
Press the preset [OneTouch Search] key, the screen will display “Seeking” and the indicator light will be yellow.
Successful seeking will display the search frequency and CTCSS/DCS, and turn on the speaker.
- You can press the [MENU] key to save the search frequency and CTCSS/DCS to the channel.
- Press and hold the [PTT] key to make a callback.
6. Advanced Features
6.1 Scanner
The radio features a built-in scanner for the VHF and UHF bands. When in Frequency (VFO) mode it will scan in steps according to your set frequency step. In Channel (MR) mode it will scan your channels.
To enable the scanner, press and hold the [#2] key for about two seconds. You can change the scanning direction with the ▲ or ▼ keys. Press and hold the [#2] key to exit scanning mode.
6.1.1 Frequency Ranger:
In frequency mode, the frequency sweep range can be precisely set. Input the start value and end value of the sweep frequency through the keyboard.
EX: Enter 144146, in frequency mode, scan in the range of 144.000-146.000MHZ. Enter 430440, in frequency mode, scan in the range of 430.000-440.000MHZ.
Note: for VFO frequency Ranger, see Menu>SCAN>Freq Ranger.
6.1.2 Channel Scan Range:
In channel mode, the scan range is allowed to be all channels in the current zone, channels that have been added to the current zone.
- All: All channels stored in the current zone.
- Memory Scan: Scanned channels that are added to the current zone.
6.1.3 Scan Modes:
The scanner is configurable to one of three ways of operation: Time, carrier or search, each of which is explained in further details in their respective section below.
- Time operation (TO): In Time Operation (TO) mode, the scanner stops when it detects a signal, and after a factory preset time out, it resumes scanning.
- Carrier operation (CO): In Carrier Operation (CO) mode, the scanner stops when it detects a signal, and after a factory preset time with no signal it resumes scanning.
- Search operation (SE): In Search Operation (SE) mode, the scanner stops when it detects a signal. To resume scanning you must press and hold the [#2] key again.
Note: for Scan mode, see Menu>SCAN>Scan Mode.
6.1.4 Scan Sub-Code (CTCSS/DCS):
To search for a CTCSS code, do the following:
- In VFO mode, enter a known frequency, such as 144.525.
- Press [MENU] key to enter menu>>Scan>>Scan Sub-Code.
- Press ▲ or ▼ to select CTCSS;
- Press [MENU] key to enter the CTCSS code, and scan the CTCSS code in sequence. When a valid CTCSS code is scanned, it stays on the CTCSS code and the speaker is turned on.
- Press [MENU] key to store the scanned CTCSS code and exit the scan to return to the previous menu. In standby mode, the CTCSS icon will be displayed on the top line of the screen. Press and hold the PTT key to make a callback.
To search for a DCS code, do the following:
- In VFO mode, enter a known frequency, such as 144.525.
- Press [MENU] key to enter menu>>Scan>>Scan Sub-Code.
- Press ▲ or ▼ to select DCS;
- Press [MENU] key to enter the DCS code scanning, and scan the DCS code in turn. When a valid DCS code is scanned, it stays on the DCS code and the speaker is turned on.
- Press [MENU] key to store the scanned DCS code and exit the scan to return to the previous menu. In standby mode, the DCS icon will be displayed on the top line of the screen. Press and hold the PTT key to make a callback.
6.1.5 Sub-Code Scan Memory:
In MR mode or VFO mode, the scanned CTCSS/DCS code can be stored as only TX CTCSS/DCS code, RX CTCSS/DCS code only, TX and RX CTCSS/DCS code to replace the CTCSS/DCS code setting of the current channel or frequency mode of the radio.
To save the settings of CTCSS/DCS code scan, the operation is as follows:
- Press [MENU] key to enter menu >> Scan >> Scan Memory.
- Press the [MENU] key to enter the Scan Memory setting, and press the ▲ or ▼ key to select:
- ENCODER: The scanned CTCSS/DCS code will be stored as the transmitted CTCSS/DCS code of the current channel or frequency mode (only replace its transmitted TX CTC/DCS).
- DECODER: The scanned CTCSS/DCS code will be stored as the receiver CTCSS/DCS code of the current channel or frequency mode (only replace its receiver RX CTC/DCS).
- ALL: The scanned CTCSS/DCS code will be stored as the received and transmitted CTCSS/DCS code of the current channel or frequency mode (at the same time as the received and transmitted Sub-Code).
- Press the [MENU] key to save the settings and return to the previous menu;
Note: Only when a valid CTCSS/DCS code is scanned and stopped, press the [MENU] key to store the CTCSS/DCS code and replace the corresponding CTCSS/DCS code of the current channel or frequency.
6.2 DTMF (Dual-Tone Multi-Frequency)
DTMF is an in-band signaling method using dual sinusoidal signals for any given code. Originally developed for telephony systems, it has proved a very versatile tool in many other areas.
In two-way radio systems, DTMF is most commonly used for automation systems and remote control. A common example would be in amateur radio repeaters where some repeaters are activated by sending out a DTMF sequence (usually a simple single-digit sequence).
DTMF Frequencies and Corresponding Codes:
| 1209Hz | 1336Hz | 1477Hz | 1633Hz | |
|---|---|---|---|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
The radio has a full implementation of DTMF, including the A, B, C and D codes. The numerical keys, as well as the [*] and [#] keys correspond to the matching DTMF codes. The A, B, C and D codes are located in the [A/B], [VFO/MR], [MENU], and [EXIT] keys respectively.
To send DTMF codes, press the key(s) corresponding to the message you want to send while holding down the PTT key.
DTMF Enc:
Set a DTMF ID as the default call ID for the current channel. Press the PTT key to transmit the selected DTMF ID. Edit the DTMF ID in Menu or with the PC programming software.
6.3 2Tone Enc
Set a 2Tone as the default call ID for the current channel. Press the PTT key to transmit the selected 2Tone. Edit the 2Tone in the PC programming software before it can be selected.
6.4 5Tone Enc
Set a 5Tone as the default call ID for the current channel. Press the [PTT] key to transmit the selected 5Tone. Edit the 5Tone in the PC programming software before it can be selected.
6.5 Dual Watch
In certain situations, the ability to monitor two channels at once can be a valuable asset. This can be achieved in one of two ways. You can either have one receiver in your radio and flip-flop between two frequencies at a fixed interval (known as Dual Watch), or you can equip a radio with two receivers (known as Dual Receive or Dual VFO). The former method is cheaper to implement and far more common than the latter.
The radio features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.
Enabling or Disabling Dual Watch Mode:
- Press the [MENU] key to enter the main menu.
- Enter 2 on the numeric keypad to get to Radio Settings.
- Press the [MENU] key to confirm, enter 18 on the numeric keypad to get to Dual Watch.
- Press the [MENU] key to select.
- OFF: Disable the dual-watch function. Turns off the sub channel, and the radio will display the main channel only. The radio will display the channel name, frequency and channel sequence on the same screen.
- Double Wait: Enable the dual-watch function. The radio will display and monitor both channels.
- Signal Wait: Enable the single-watch function. The radio will display both channels. Transmit and receive on the main channel only, sub Channel disables reception. Sub channel will Display icon.
- Press the [MENU] key to confirm.
- Press [EXIT] to return to the previous menu.
Press and hold [A/B] to switch Double Wait / Signal Wait / Off dual watch mode.
6.6 Manual Programming (Channels Memory)
Memory channels are an easy way to store commonly used frequencies so that they can easily be retrieved at a later date.
The radio features 999 memory channels that each can hold: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/PTT-ID settings and a six-character alphanumeric identifier or channel name.
Frequency Mode vs. Channel Mode:
In standby mode, press [VFO/MR] key to switch between frequency (VFO) mode and channel (MR) mode. These two modes have different functions and are often confused.
Ex 1. Programming a Channel Repeater Offset with CTCSS Tone:
EXAMPLE: New memory in Channel 28:
- RX = 432.55000 MHz
- TX = 437.55000 MHz (This is a (+ 5) Offset)
- TX CTCSS tone 123.0
- Press the [MENU] key to switch between menus.
- Press [VFO/MR] key to set the radio to VFO mode, and the VFO icon is displayed on the left.
- [3][7] (123.0) - Selects desired TX encode tone (Ex 123 CTCSS)
- [3][1][3][0][5] - Enter the OFFSET frequency (Ex. 5.00MHz)
- [3][1][4][2] - Select the offset direction (Ex. positive offset)
- Enter RX frequency (Ex. 43255000)
- [3][1][7][2][8] - Enter the same channel (Ex 10) --> channel has been added
- Press [VFO/MR] key to return to the MR mode and the channel number will reappear.
Ex 2. Programming a Simplex Channel with CTCSS Tone:
EXAMPLE: New memory in Channel 28:
- RX = 432.6500 MHz
- TX CTCSS tone 123.0
- Press the [MENU] key to switch between menus.
- Press [VFO/MR] key to set the radio to VFO mode, and the VFO icon is displayed on the left.
- [3][7] (123.0) - Selects desired TX encode tone (Ex 123 CTCSS)
- Enter RX frequency (Ex. 43265000)
- [3][1][7][2][8] - Enter the same channel (Ex 10) --> channel has been added
- Press and hold the [VFO/MR] key to return to the MR mode and the channel number will reappear.
6.7 Repeaters Programming
The following instructions assume that you know what transmit and receive frequencies your repeater employs, and that you're authorized to use it.
- Press [VFO/MR] key, the transceiver is set to VFO mode, and the VFO icon will be displayed on the left.
- Use the numeric keypad to enter the repeater's output (your receive) frequency.
- Press [MENU][3][1][3] to get the offset frequency.
- Use the numeric keypad to enter the specified frequency offset.
- Press [MENU] to confirm and save.
- Press [MENU][3][1][4] to get the offset direction.
- Use the ▲ or ▼ keys to select plus (positive) or minus (negative) offset.
- Press [MENU] to confirm and save.
Optional:
- Save to memory, see the section called “Manual programming” for details.
- Set up CTCSS; see the section called “CTCSS” for details.
- Press [EXIT] to exit the menu. If everything went well, you should be able to make a test call through the repeater.
NOTE: If you're experiencing problems making a connection to the repeater, check your settings and/or go through the procedure again.
Certain Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open up the repeater. To see how this is done with the radios, see the section called "1750Hz Tone-burst".
If you're still unable to make a connection, contact the person in charge of the radio system with your employer or your local amateur radio club, as the case may be.
6.8 Amateur Radio Setup
In contrast with Commercial radio operators, who often need very specific requirements to be compatible with a very specific radio implementation, Amateur radio operators tend to need the broadest possible settings in order to be compatible with as many systems as possible. This basically implies turning all the fancy features that you typically might need for a commercial setup off.
In a typical Amateur radio setup the following settings would be recommended:
Radio Setting:
- Turn ANI, DTMFST, PTT-ID off and PTT-LT to Oms (menu items 22 through 24).
- Turn off Squelch Tail Elimination (Tail) features (menu items 26).
- Turn roger beep (ROGER) off (menu item 10).
Program Channel:
- Set bandwidth to Wide (menu item 4).
- Turn DCS and CTCSS off (menu items 5 through 8).
- Turn Signaling code off and SPK-Mute (menu items 9 and 10).
8. Troubleshooting Guide
| Phenomena | Analysis | Solution |
|---|---|---|
| You cannot turn on the radio. | The battery may be installed improperly. The battery power may run out. The battery may suffer from poor contact caused by dirty or damaged battery contacts. | Remove and reattach the battery. Recharge or replace the battery. Clean the battery contacts or replace the battery. |
| During receiving, the voice is weak or intermittent. | The battery voltage maybe low. The volume level may be low. The antenna maybe loose or maybe installed incorrectly. | Recharge or replace the battery. Increase the volume. Turn off the radio, and then remove and reattach the antenna. |
| You cannot communicate with other group members. | The speaker maybe blocked. The frequency or signaling type maybe inconsistent with that of other members. You may be too far away from other members. You may be interrupted by radios using the same frequency. | Clean the surface of the speaker. Verify that your TX/RX frequency and signaling type are correct. Move towards other members. Change the frequency, or adjust the squelch level. |
| You hear unknown voices or noise. | The radio in analog mode maybe set with no signaling. | Request your dealer to set signaling for the current channel to avoid interference. |
| You are unable to hear anyone because of too much noise and hiss. | You may be too far away from other members. You may be in an unfavorable position. For example, your communication may be blocked by high buildings or blocked in an underground area. It may be the result of external disturbance (such as electromagnetic interference). | Move towards other members. Move to an open and flat area, restart the radio, and try again. Stay away from equipment that may cause interference. |
| The radio keeps transmitting. | VOX may be turned on or the headset is not installed in place. | Turn off the VOX function. Check that the headphones are in place. |
NOTE: If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.
9. Technical Specifications
| GENERAL | |
|---|---|
| Channel Capacity | 640 |
| Channel Spacing | 25.0 KHz/12.5 KHz |
| Input Voltage | 7.4 VDC |
| Battery Life: 5% TX, 5% RX, 90% Standby | Li-on: 15 hours @ 5 watts |
| Operating temperature | -10°C to 60°C |
| Antenna Impedance | 50Ω |
| Radio Dimensions | 135mm X 63mm X 39mm (not including antenna) |
| Radio Weight | 290 g (with Li-ON battery) |
| TRANSMITTER | |
|---|---|
| Frequency Range (TX) | 144 to 148 MHz, 420 to 450 MHz (America version) 144 to 148 MHz, 430 to 450 MHz (Canadian version) *144 to 146 MHz, 430 to 440 MHz (EU CE version) |
| RF Output Power | 7 Watts Max |
| Modulation | 16K0F3E/11K0F3E |
| Spurious Emission | -16 dBm<1GHz, -16 dBm>1GHz |
| Frequency Stability | ±2.5 ppm |
| Audio Distortion | ≤5% |
| FM Hum & Noise | 40 dB |
| RECEIVER | |
|---|---|
| Frequency Range | 108-136, 136-174, 220-260, 350-390, 400 to 520 MHz (Scan Receiver) *144 to 146 MHz, 430 to 440 MHz (EU CE version) |
| Sensitivity: 12 dB SINAD | -120 dBm |
| Adjacent Channel Selectivity | -60 dBm |
| Intermodulation and Rejection | -70 dBm |
| Rated Audio Power Output | 0.75 Watts @ 16 Ω |
| Rated Audio Distortion | ≤5% |
NOTE: All specifications may be modified without prior notice or liability. Thank you.
10. User Tips
- Programming Software: To fully utilize the radio's capabilities, programming software is highly recommended. This allows for easier management of channels and advanced settings.
- GPS and APRS: The GPS and APRS (Automatic Packet Reporting System) functions, including sharing and requesting location information, are reported to work flawlessly.
- Build Quality: Users have noted the impressive build quality of the device.
- USB-C Charging: The USB-C charging capability of the battery pack is very practical for field use, allowing charging via car, power bank, or laptop.
- FM Radio: The built-in FM radio works well for entertainment.
- Bluetooth Functionality: While listed as Bluetooth capable, some users have reported difficulty finding or activating this setting. It may not be fully functional or present on all units.
- Regulatory Compliance: Be aware of local regulations regarding radio use. In some countries, like Brazil, specific approval or licensing may be required.
11. Warranty and Support
PDF User Manual
A detailed user manual in PDF format is available for download. This document provides comprehensive instructions and diagrams for all functions and features of your Baofeng UV-5RH PRO. View User Manual (PDF)
Contact Information
For technical support, warranty claims, or any other inquiries, please contact:
PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED
ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong
Website: www.baofengradio.com or www.pofungshop.com
Print version: 5RH PRO(501) V1.0
Disclaimer
The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for the possible errors or omissions. With the continuous development of technology, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation and dissemination of this handbook may be made in any form without the prior written authorization of our department.
