1. Introduction
The JIKONG JK-BD6A20S6P Smart Battery Management System (BMS) is an intelligent active balance power management system designed for Li-ion, LiFePo4, and LTO batteries. It supports battery configurations from 8S to 24S and provides comprehensive protection and balancing functions to ensure optimal battery performance and longevity.
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your JIKONG Smart BMS.
2. Product Features
- Active Balancing: Transfers energy from higher energy cells to lower energy cells with minimal loss, operating continuously during charging, discharging, or idle states. Supports balancing currents up to 0.6A (600mA), with general active balancing capabilities up to 1-2A for larger capacity battery packs.
- Multi-interface Display: Supports APP (iOS, Android, HarmonyOS), PC software, and external display screens.
- Major Interfaces: GPS, RS485, CAN, Display, Heating, NTC.
- High-performance MCU: Main control chip for efficient operation.
- Full Aluminum Alloy Shell: Provides excellent heat dissipation.
- Comprehensive Protection: Overcharge protection, over-discharge protection, overcurrent protection, short circuit protection.
- Adjustable Parameters: Freely adjust multiple protection values via the app or PC software.
- Protocol Docking: Compatible with mainstream inverter communication protocols.
3. Package Contents
Verify that all items are present in the package:
- 1 x JIKONG JK-BD6A20S6P Smart BMS
- 1 x Switch key (long 50cm)
- 2 x Sampling Cables (Sampling line A long 70cm, Sampling line B long 70cm)
- 1 x NTC (long 40cm)
4. Installation and Wiring
Safety Precautions: Before proceeding with installation, ensure the battery pack is disconnected from any power sources. Wear appropriate personal protective equipment (PPE) such as insulated gloves and eye protection. Incorrect wiring can lead to damage to the BMS, battery, or personal injury.
4.1. General Wiring Steps
- Connect all balance cables to the battery cells first.
- Insert the balance cable connector into the BMS.
- Connect the B-line (total negative electrode) and the P-line (total positive electrode) to the battery.
4.2. Wiring Diagram for 24-String Cells
Detailed connections for 24-string cells:
- Connect individual cell voltage taps (B1, B2, ..., B24) to the corresponding pins on the sampling port A and B.
- Connect the main negative terminal of the battery pack to the B- terminal on the BMS.
- Connect the main positive terminal of the battery pack to the P- terminal on the BMS.
- The P+ terminal from the battery connects to the inverter/charger.
- The P- terminal from the BMS connects to the inverter/charger.
- Ensure the NTC temperature sensor is placed appropriately within the battery pack for accurate temperature monitoring.
4.3. Wiring Diagram for 16-String Cells
Detailed connections for 16-string cells:
- Connect individual cell voltage taps (B1, B2, ..., B16) to the corresponding pins on the sampling port A and B.
- Connect the main negative terminal of the battery pack to the B- terminal on the BMS.
- Connect the main positive terminal of the battery pack to the P- terminal on the BMS.
- The P+ terminal from the battery connects to the inverter/charger.
- The P- terminal from the BMS connects to the inverter/charger.
- Ensure the NTC temperature sensor is placed appropriately within the battery pack for accurate temperature monitoring.
5. Operation
5.1. Initial Power-Up
After completing the wiring, connect the battery pack to the load/charger. The BMS will power on automatically. You can verify its status via the mobile app or an external display.
5.2. Mobile App and PC Software
The JIKONG Smart BMS supports mobile applications for iOS, Android, and HarmonyOS, as well as PC software for comprehensive monitoring and control.
Key functions available through the app/software:
- Real-time monitoring of voltage, current, temperature, State of Charge (SOC), and number of strings.
- Adjustment of protection parameters such as overcharge, over-discharge, overcurrent, and temperature limits.
- Monitoring of active balancing status and efficiency.
- Protocol docking for inverter communication.
To download the APP and user manual, scan the QR code on the BMS unit or visit WWW.JK-BMS.COM.
5.3. External Display (Optional)
An optional external display can be connected to the BMS to view key battery information at a glance.
5.4. Inverter Communication
The BMS supports various inverter communication protocols, allowing seamless integration with existing power systems. Protocols can be set up via the mobile app or PC software.
Supported CAN Protocols include: Growatt BMS CAN Protocol V1.02, PYLON CANBUS Protocol V1.2, Growatt xxSxxP ESS Protocol V2.01, CAB-BUS_BMS_Protocol_201707, INVT BMS CAN Bus protocol V1.02, GoodWe LV BMS Protocol (CAN V1.7for ES/EM/BP Series), FSS-ConnectingBat-Ti-en-10 (Version 1.0), PACE BMS Modbus Protocol for RS485, MUST PV1800F-CAN communication protocol.
6. Maintenance
- Regular Monitoring: Periodically check the battery parameters via the app or display to ensure normal operation.
- Firmware Updates: Keep the BMS firmware updated to benefit from the latest features and improvements. Check the official JIKONG website or app for updates.
- Physical Inspection: Ensure all connections are secure and free from corrosion. The aluminum alloy shell provides good heat dissipation, but ensure adequate airflow around the unit.
- Balancing: The active balancing feature works continuously. No manual intervention is typically required for balancing, but monitoring its efficiency can be beneficial.
7. Troubleshooting
If you encounter issues with your JIKONG Smart BMS, consider the following:
- No Power/Display:
- Check all wiring connections, especially the B- and P- lines, and the balance cables.
- Ensure the battery pack has sufficient voltage.
- Balancing Issues:
- Verify that all balance cables are correctly connected to each cell.
- Check the cell voltage differences in the app; if they are consistently high, there might be an issue with a cell or the balance connection.
- App/Software Connection Problems:
- Ensure Bluetooth is enabled on your mobile device and the BMS is within range.
- For PC software, verify the communication module (e.g., RS485) is correctly connected and drivers are installed.
- Restart the app/software and the BMS.
- Protection Triggered (Overcharge, Over-discharge, Overcurrent, Short Circuit):
- Identify the cause of the protection event (e.g., charger voltage too high, load current too high, short circuit).
- Address the root cause before attempting to reset the BMS (if applicable). The BMS is designed to protect the battery, so these triggers indicate a potential issue with the battery or system.
For persistent issues, refer to the detailed user manual available on WWW.JK-BMS.COM or contact JIKONG technical support.
8. Specifications
| Feature | Specification |
|---|---|
| Model | JK-BD6A20S6P |
| Battery Series Support | 8S-24S |
| Battery Type Compatibility | Li-ion, LiFePo4, LTO |
| Continuous Charge Current | 60A |
| Continuous Discharge Current | 60A |
| Balance Function | Active Balanced BMS |
| Balance Current | 0.6A (600mA) |
| Charge and Discharge Port | Common Port BMS |
| Protection Functions | Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection |
| Bluetooth | Yes |
| Communication Interfaces | RS485, CAN (customized), GPS (customized) |
| Usage Scenario | Power BMS, Energy Storage BMS, 3C Digital BMS |
| Certification | CE, FCC |
| Voltage detection accuracy | ±0.015V |
| Short circuit protection response | 10-500μs |
9. User Tips
- Download the App: For the best experience and full control, download the JIKONG Smart BMS app from WWW.JK-BMS.COM. It allows for real-time monitoring and parameter adjustments.
- Check Connections: Always double-check all balance wire and main power connections before powering on the system to prevent damage.
- Monitor Cell Voltages: Regularly monitor individual cell voltages through the app to ensure proper balancing and identify any potential issues early.
- Heat Dissipation: While the aluminum shell aids in heat dissipation, ensure the BMS is installed in a location with adequate airflow to prevent overheating, especially during high charge/discharge cycles.
10. Warranty and Support
JIKONG products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please visit the official JIKONG website at WWW.JK-BMS.COM or contact your local distributor.
The manufacturer provides support for customized solutions regarding structure, hardware (temperature control, power display board, soft switch), and software (APP, host computer).