Introduction
The Radiomaster RP4TD-M is a compact and lightweight ExpressLRS 2.4GHz Mini True Diversity Receiver, designed for optimal performance in applications where minimizing weight is crucial, such as racing drones, RC airplanes, and FPV drones. Building on the success of the RP4TD, this 'M' version weighs just 1 gram and leverages 'Gemini' technology for superior interference mitigation. Its optimized circuit design features dual-channel 2.4GHz radios, delivering exceptional signal sensitivity, signal-to-noise ratio, and overall performance. The RP4TD-M also includes a built-in TCXO (temperature compensated crystal oscillator) for high stability and accuracy in frequency control, ensuring consistent and reliable signal reception even in extreme temperature conditions.
Official product video showcasing the Radiomaster RP4TD-M receiver's features and compact design.
Features
- Mini size true diversity Gemini receiver
- Class leading SNR and RSSI performance
- Built-in TCXO (temperature compensated crystal oscillator)
- Optimized PCB design for better heat dissipation
- Upgraded antenna with greater durability and performance
- 2x 10mW RF Telemetry power output
- Compatible with all 2.4GHz ExpressLRS modules and transmitters with built-in 2.4GHz ExpressLRS

Radiomaster RP4TD-M ExpressLRS Receiver, highlighting its lightweight, dual-channel, high sensitivity, and TCXO oscillators.

Dual-antenna design for improved signal stability and range, and upgraded rigid antennas for greater durability and performance.

Close-up of the TCXO oscillator on the RP4TD-M board, emphasizing premium accuracy and stability.
Package Contents
- 1 * RP4TD-M ExpressLRS True 2.4GHz Diversity Receiver
- 1 * CRSF wire
- 3 * Heat-Shrinkable Tube
- 2 * 65mm 2.4GHz T Antenna (Installed on receiver)
- 1 * User Manual

Package contents including the RP4TD-M receiver, CRSF wire, heat-shrinkable tubes, and T antennas.
Specifications
| Feature | Detail |
|---|---|
| Item | RP4TD-M ExpressLRS 2.4GHz Mini True Diversity Receiver |
| Type | ISM |
| MCU | ESP32 |
| RF Chip | SX1281 x 2 |
| Antenna | 65mm 2.4GHz T Antenna x 2 |
| Frequency Range | 2.4GHz |
| Maximum Refresh Rate | 500Hz / F1000Hz |
| Telemetry RF Power | Max 2x 10mW |
| Working Voltage | DC 5.0V |
| Wifi Updates | Yes |
| Weight (Without antennas) | 1.00g |
| Weight (With antennas) | 3.30g |
| Dimension | 18.10 x 16.0mm |
| Firmware Version | ExpressLRS V3.4.3 pre-installed |
| FW Target | RadioMaster RP4TD-M 2400 RX |
| Bus Interface | CRSF |
| High-concerned chemical | None |
| Is Electric | No Battery |
| Wheelbase | Bottom Plate |
| Is it battery/power supply | N |
| Is it charger/adapter | N |
| Is Batteries Included | No |
| For Vehicle Type | Airplanes |
| Tool Supplies | Assembled class |
| Four-wheel Drive Attributes | Assemblage |
| Remote Control Peripherals/Devices | Remote Controller |
| Upgrade Parts/Accessories | Adapter |
| RC Parts & Accs | RECEIVERS |
| Material | Composite Material |
| Origin | Mainland China |
| Recommend Age | 14+y |
| Use | Vehicles & Remote Control Toys |

Detailed specifications table for the RP4TD-M receiver.

Dimensions of the RP4TD-M receiver (18.10 x 16.00 x 2.00mm) and its 65mm T antenna.

Weight of the RP4TD-M receiver, showing 1.00g without antennas.
Setup
Binding Procedure (ExpressLRS)
- Prepare your Transmitter: Ensure your 2.4GHz ExpressLRS module or built-in ExpressLRS transmitter is updated to a compatible firmware version (e.g., ExpressLRS V3.4.3 or newer).
- Power Cycle the Receiver: Power on your RP4TD-M receiver. Immediately power it off. Repeat this process two more times. On the third power-up, the receiver's LED should flash rapidly, indicating it is in binding mode.
- Initiate Binding on Transmitter: On your ExpressLRS transmitter, navigate to the ELRS LUA script or menu and select the 'Bind' option.
- Confirm Binding: If successful, the receiver's LED will turn solid, indicating a successful bind.
The RP4TD-M comes with ExpressLRS V3.4.3 firmware pre-installed, targeting RadioMaster RP4TD-M 2400 RX. Ensure your transmitter firmware is compatible for seamless operation.
Wiring
Connect the included CRSF wire to the appropriate pads on your flight controller and the RP4TD-M receiver. The receiver uses a CRSF bus interface. Refer to your flight controller's manual for specific wiring diagrams for CRSF receivers. Typically, this involves connecting TX, RX, 5V, and GND pins.

Close-up view of the RP4TD-M receiver board, showing connection pads for wiring.
Operating
Once bound and correctly wired, the RP4TD-M receiver will provide reliable control and telemetry data to your ExpressLRS compatible transmitter. The dual-channel 2.4GHz radios and 'Gemini' technology ensure robust signal reception and interference mitigation, while the TCXO oscillator maintains frequency stability for consistent performance. The 2x 10mW RF Telemetry power output allows for real-time feedback from your aircraft.
Maintenance
- Physical Inspection: Regularly inspect the receiver and antennas for any signs of damage, such as bent pins, frayed wires, or cracked heat-shrink tubing.
- Heat Management: The RP4TD-M features an optimized PCB design for better heat dissipation. Ensure it is installed in a location with adequate airflow to prevent overheating, especially during extended use or in enclosed spaces.
- Firmware Updates: While the receiver comes pre-installed with ExpressLRS V3.4.3, periodically check the official ExpressLRS and Radiomaster websites for newer firmware versions. Updates can provide performance improvements, bug fixes, and new features. Firmware updates can typically be performed via Wi-Fi.
- Antenna Placement: Ensure antennas are positioned correctly and securely to maximize signal reception and diversity benefits. Avoid placing them near carbon fiber or large metal objects that can block RF signals.
Troubleshooting
- Receiver Not Binding: Ensure your transmitter is also in bind mode and running a compatible ExpressLRS firmware version. Double-check the power cycling sequence for the receiver (three rapid power cycles).
- No Control/Telemetry: Verify all wiring connections (CRSF, 5V, GND) are correct and secure. Check the flight controller's configuration to ensure the correct UART is selected for CRSF and that the serial receiver is enabled.
- Intermittent Signal Loss: Check antenna placement and ensure they are not obstructed. Inspect antennas for damage. Ensure your transmitter's RF power is set appropriately for your flying environment.
- Receiver LED Status: A solid LED typically indicates a successful bind and active connection. A rapidly flashing LED indicates binding mode. A slowly flashing LED might indicate a lost connection or an issue with the firmware.
User Tips
- Antenna Orientation: For optimal signal diversity, try to orient your two T-antennas at a 90-degree angle to each other. This helps ensure at least one antenna has a good signal path regardless of aircraft orientation.
- Heat Shrink Protection: Use the provided heat-shrinkable tubes to protect the receiver from environmental elements and short circuits, especially in FPV drone builds where space is tight and crashes are possible.
- Mounting: Given its lightweight nature, secure the receiver firmly to prevent vibrations from affecting its performance or causing connections to loosen. Double-sided foam tape can be effective.
Warranty & Support
For warranty claims, technical support, or further assistance, please contact your retailer or the official Radiomaster support channels. Keep your proof of purchase for any warranty-related inquiries. Detailed support resources, including the latest firmware and troubleshooting guides, may be available on the Radiomaster official website.