Estardyn SPI TFT LCD Display Module

Contents

Estardyn SPI TFT LCD Display Module User Manual

Models: 1.8", 2.4", 2.8" TFT with Touch Display

1. Introduction

This manual provides detailed instructions and specifications for the Estardyn SPI TFT LCD Display Modules, available in 1.8-inch, 2.4-inch, and 2.8-inch sizes, many featuring touch functionality. These modules are designed for integration into various electronic projects requiring a compact, colorful display with a simple SPI interface.

Estardyn TFT LCD Modules 1.8, 2.4, 2.8 inch with stylus
Figure 1: Overview of Estardyn 1.8", 2.4", and 2.8" TFT LCD modules, including a stylus for touch models.

2. Specifications

The Estardyn SPI TFT LCD Display Modules come in various configurations. Below are the general and specific parameters for different sizes.

2.1 General Specifications

  • Type: TFT
  • High-concerned chemical: None
  • is_customized: Yes
  • Origin: Mainland China

2.2 0.96-inch Display Module

FeatureParameter
Display ModeNormally black IPS
Display FormatGraphic 80RGB*160 Dot-matrix
Input DataSPI interface
Drive ICST7735S
Dimensional outline24(W)*30 (H)*2.8+/-0.1(T)mm
Resolution80RGB*160 Dots
LCD Active area10.8 (W)*21.7 (H)
Dot pitch0.135(H) x 0.1356(V) mm
Viewing DirectionAll View
Operating Temperature-20~70°C

2.3 1.3-inch Display Module

FeatureParameter
Display ModeNormally black IPS
Display FormatGraphic 240RGB*240 Dot-matrix
Input DataSPI interface
Drive ICST7789VW
Dimensional outline27.78(W)*39.22 (H)*3.0+/-0.1(T)mm
Resolution240RGB*240 Dots
LCD Active area23.4 (W)*23.4 (H)
Dot pitch0.0975(H) x 0.0975(V) mm
Viewing DirectionAll View
Operating Temperature-20~70°C

2.4 1.77-inch Display Module

  • Display Type: TFT 85K/Transmissive
  • Drive IC: ST7735S OR Compatible
  • Operating Voltage: VCC=3.0-5.0V
  • Viewing Direction: 12 O'CLOCK
  • Backlight: 2 Chip White LED, I=30mA(Typ)/40mA(Max), V=3.0V(Typ)
  • Operating Temperature: -20°C to 70°C
  • Storage Temperature: -30°C to 80°C
  • General Tolerance: ±0.2
1.77 inch TFT LCD module technical drawing with dimensions and pinout
Figure 2: Technical drawing for the 1.77-inch TFT LCD module, showing dimensions and pin assignments.

2.5 2.4-inch Display Module (with/without touch)

NameParameter
Display ColorRGB 65K color
SKUMSP2402 (with touch screen), MSP2401 (no touch screen)
Screen Size2.4 (inch)
TypeTFT
Driver ICST7789V
Resolution320*240 (Pixel)
Module Interface4-wire SPI interface
Active Area (AA area)36.72x48.96 (mm)
Module PCB Size77.18x42.72 (mm)
Operating Temperature-20℃~60℃
Storage Temperature-30℃~70℃
VCC power voltage3.3V~5V
Logic IO port voltage3.3V(TTL)
Power ConsumptionTBD
Rough Weight (Package containing)No touch: 26(g) / With touch: 36(g)
2.4 inch TFT LCD module product parameters table
Figure 3: Detailed product parameters for the 2.4-inch TFT LCD module.

3. Setup and Pin Descriptions

Proper connection of the display module to your microcontroller or development board is crucial for its operation. Refer to the pin descriptions and wiring diagrams below for each module variant.

3.1 0.96-inch Display Module Pinout

PIN NoSymbolDescription
1GNDGround
2VCCPower 3.3V
3SCLSerial Clock Pin
4SDASerial Data Input
5RESLCM Reset Pin (Active low for initialization, pull high for normal operation)
6DCData/Command Control
7CSChip Select
8BLKBacklight Control Pin

3.2 1.3-inch Display Module Pinout

PIN NoSymbolDescription
1GNDGround
2VCCPower 3.3V
3SCLSerial Clock Pin
4SDASerial Data Input
5RESLCM Reset Pin (Active low for initialization, pull high for normal operation)
6DCData/Command Control
7BLKBacklight Control Pin

3.3 1.77-inch Display Module Wiring

Refer to the technical drawing for detailed pin assignments and backlight circuit information.

1.77 inch TFT LCD module wiring diagram and dimensions
Figure 4: Wiring diagram and dimensions for the 1.77-inch TFT LCD module. Note the backlight circuit details.

3.4 1.8-inch Display Module Wiring and Power Considerations

The 1.8-inch module typically uses an SPI serial port with a 128x160 resolution. Example IO connections are provided below. Pay close attention to power supply requirements.

sbit LCD_CS =P0^0; //chip select
sbit LCD_AO =P0^2; //data/command switch
sbit LCD_SDA =P1^5; // Data
sbit LCD_SCK =P1^7; //clock
sbit LCD_REST =P0^1; //reset
            
  • TFT Power Supply: The screen power supply is 2.8-3.3V. Do not use 5V directly for the screen itself. Modules with an integrated PCB often include a 3V regulator IC, allowing a 5V input to the module's VCC pin.
  • Backlight Power Supply (LED pin): The maximum backlight power supply is 3.2V. If using a 3.3V power supply, connect a 5 ohm current limiting resistor in series. If using a 5V power supply, a 25 ohm resistor should be used in series.
1.8 inch TFT LCD module wiring diagram and dimensions
Figure 5: Wiring diagram and dimensions for the 1.8-inch TFT LCD module, including SD card interface pins.
Back view of 2.8 inch and 2.4 inch TFT modules showing SD card slot and pin labels
Figure 6: Back view of 2.8" and 2.4" TFT modules, highlighting the SD card slot and pin labels for connection.

4. Operating Instructions

These TFT LCD modules utilize a Serial Peripheral Interface (SPI) for communication with a host microcontroller. The SPI interface typically requires a few I/O pins (SCL, SDA, CS, DC, RES) for display control and data transfer.

4.1 Basic Operation

  1. Power On: Ensure the module is correctly wired and powered within the specified voltage range (3.3V for logic, 2.8-3.3V for TFT, with appropriate backlight resistors if needed).
  2. Initialization: Send the necessary initialization commands to the display controller IC (e.g., ST7735S, ST7789V) via the SPI interface. This typically involves resetting the display, setting display parameters, and turning on the display.
  3. Data Transfer: Use the SPI interface to send pixel data to the display. The DC pin differentiates between command and data bytes.
  4. Touch Functionality (for touch models): If your module includes touch, it will typically have additional pins (e.g., GT_CS, GT_SI, GT_SO, GT_SCL, GT_INT) for touch controller communication, often also via SPI or a similar serial protocol. Consult the specific touch controller datasheet for detailed interaction.
  5. SD Card (if present): Modules with an SD card slot can be used to store images or other data for display. The SD card interface also typically uses SPI.

Sample programs and underlying driver technical support are often provided by the manufacturer to assist with software development.

5. Maintenance

  • Cleaning: Use a soft, dry, lint-free cloth to gently wipe the display surface. Avoid using abrasive cleaners or solvents that could damage the screen.
  • Handling: Handle the module by its edges to avoid touching the display area or sensitive electronic components.
  • Storage: Store the module within the specified storage temperature range (-30℃ to 80℃) and in a dry environment to prevent damage from moisture or extreme temperatures.
  • Power: Always ensure correct voltage and current limiting for the backlight to prevent LED damage.

6. Troubleshooting

  • Display Not Lighting Up:
    • Check power connections (VCC, GND) and ensure correct voltage.
    • Verify backlight (BLK/LED) connection and ensure appropriate current limiting resistor is used.
    • Confirm the display initialization sequence in your code is correct.
  • Garbled Display/Incorrect Colors:
    • Check SPI connections (SCL, SDA, CS, DC, RES) for continuity and correct pin assignment.
    • Ensure the correct display driver IC (e.g., ST7735S, ST7789V) is selected in your software.
    • Verify data transfer format and timing for the SPI interface.
    • Confirm the resolution settings in your code match the display module's resolution.
  • Touch Screen Not Responding:
    • For touch models, check the touch controller's specific connections (e.g., GT_CS, GT_SI, GT_SO, GT_SCL, GT_INT).
    • Ensure the touch controller is correctly initialized and polled in your software.
    • Calibrate the touch screen if necessary.
  • SD Card Not Detected:
    • Check SD card SPI connections (SDI, SDO, SD_SCK, SD_CS).
    • Ensure the SD card is properly inserted and formatted.
    • Verify SD card initialization code.

7. User Tips

No specific user tips were available from buyer reviews or Q&A for this product. However, general best practices for working with display modules include:

  • Always double-check pin connections before applying power to prevent damage.
  • Start with basic example code provided by the manufacturer or community to verify functionality before integrating into complex projects.
  • Consider using a logic level shifter if your microcontroller operates at a different voltage than the display module's logic voltage (e.g., 5V microcontroller with 3.3V display logic).

8. Support and Warranty

For technical assistance, driver code, or further documentation, please refer to the manufacturer's official resources or contact your vendor. Specific warranty information is typically provided at the point of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.