Estardyn TFT Display 0.96/1.3/1.44/1.77/1.8/2.0 inch LCD

Contents

Estardyn TFT LCD Module Instruction Manual

Models: 0.96, 1.3, 1.44, 1.77, 1.8, 2.0 inch IPS Full Color LCD Modules

Driver ICs: ST7735, ST7789V

1. Introduction

This manual provides detailed instructions for the Estardyn series of TFT LCD modules. These modules are designed for various embedded applications, offering full-color display capabilities with a simple SPI interface. This guide covers setup, operation, specifications, and troubleshooting for the 0.96, 1.3, 1.44, 1.77, 1.8, and 2.0 inch variants.

Assortment of Estardyn TFT LCD Modules
Figure 1: Assortment of Estardyn TFT LCD Modules

2. Key Features

  • Full-Color Display: Supports 65K color display for rich visuals.
  • SPI Serial Bus: Utilizes a 4-wire SPI interface, requiring minimal I/O pins for control.
  • Wide Range of Sizes: Available in 0.96, 1.3, 1.44, 1.77, 1.8, and 2.0 inch diagonal sizes.
  • IPS Technology: Many models feature IPS (In-Plane Switching) for wide viewing angles.
  • Integrated Driver ICs: Equipped with ST7735S or ST7789VW driver ICs.
  • SD Card Slot (Optional): Some modules include an SD card slot for easy expansion and data storage.
  • Arduino Compatibility: Designed for easy integration with Arduino and similar microcontroller platforms.

3. Technical Specifications

3.1. General Specifications

  • Brand Name: Estardyn
  • Type: TFT
  • Display Mode: 1 (Normally black IPS for most models)
  • Origin: Mainland China
  • Customization: Yes

3.2. Module Specific Specifications

0.96 inch TFT Module

ParameterValue
Size0.96 inch
Display ModeNormally black IPS
Display FormatGraphic 80RGB*160 Dot-matrix
Input DataSPI interface
Drive ICST7735S
Dimensional Outline24(W)*30 (H)*2.8+/-0.1(T)mm
Resolution80RGB*160 Dots
LCD Active Area10.8 (W)*21.7 (H)mm
Dot Pitch0.135(H) x 0.1356(V) mm
Viewing DirectionAll View
Operating Temperature-20~70°C
0.96 inch TFT module displaying a car
Figure 2: 0.96 inch TFT Module (Example Display)

1.3 inch TFT Module

ParameterValue
Display ModeNormally black IPS
Display FormatGraphic 240RGB*240 Dot-matrix
Input DataSPI interface
Drive ICST7789VW
Dimensional Outline27.78(W)*39.22 (H)*3.0+/-0.1(T)mm
Resolution240RGB*240 Dots
LCD Active Area23.4 (W)*23.4 (H)mm
Dot Pitch0.0975(H) x 0.0975(V) mm
Viewing DirectionAll View
Operating Temperature-20~70°C
1.3 inch TFT module (Blue PCB) displaying Earth
Figure 3: 1.3 inch TFT Module (Blue PCB)

1.77 inch TFT Module

1.77 inch TFT LCD Module Pin Assignment and Dimensions
Figure 4: 1.77 inch TFT LCD Module Pin Assignment and Dimensions

1.8 inch TFT Module

1.8 inch TFT LCD Module Pin Assignment and Dimensions
Figure 5: 1.8 inch TFT LCD Module Pin Assignment and Dimensions

2.0 inch TFT Module (GMT020-01)

ItemContentsUnit
LCD Size2.0 inch (Diagonal)-
Display ModeNormally black-
Resolution240(H)RGB x 320(V)-
Dot pitch0.1275(H) x 0.1275(V) mm-
Active area30.6(H) x 40.8(V) mm-
Module size35.7(H) x 51.2(V) x 2.2(D) mm-
Color arrangementRGB Vertical stripe-
Interface4 Line SPI-
Drive ICST7789VW-
Luminance(cd/m2)400 (TYP)-
Viewing DirectionAll View-
Backlight4 White LED-
Operating Temp.-20℃ ~ + 70℃℃
Storage Temp.-30℃ ~ + 80℃℃
WeightTBDg
2.0 inch TFT LCD Module (GMT020-01) Mechanical Drawing
Figure 6: 2.0 inch TFT LCD Module (GMT020-01) Mechanical Drawing

2.4 inch TFT Module

NameParameter
Display ColorRGB 65K color
SKUhave touch screen: MSP2402
have no touch screen: MSP2401
Screen Size2.4(inch)
TypeTFT
Driver ICST7789V
Resolution320*240 (Pixel)
Module Interface4-wire SPI interface
Active Area (AA area)36.72x48.96(mm)
Module PCB Size77.18x42.72(mm)
Operating Temperature-20℃~60℃
Storage Temperature-30℃~70℃
VCC power voltage3.3V~5V
Logic IO port voltage3.3V(TTL)
Power ConsumptionTBD
Rough Weight (Package containing)No touch: 26(g) / With touch: 36(g)
2.4 inch TFT LCD Module Product Parameters Table
Figure 7: 2.4 inch TFT LCD Module Product Parameters Table

4. Setup and Wiring

The Estardyn TFT LCD modules typically use a 4-wire SPI interface for communication. Ensure correct pin connections and power supply to avoid damage.

4.1. Pin Descriptions

0.96 inch TFT Module Pinout

PIN No.SymbolDescription
1GNDGround
2VCCPower 3.3V
3SCLSerial clock pin.
4SDASerial data input
5RESLCM Reset pin. This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin pull high during normal operation.
6DCData/Command Control
7CSChip Select
8BLKBacklight control pin

1.3 inch TFT Module Pinout

PIN No.SymbolDescription
1GNDGround
2VCCPower 3.3V
3SCLSerial clock pin.
4SDASerial data input
5RESLCM Reset pin. This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin pull high during normal operation.
6DCData/Command Control
7BLKBacklight control pin

2.0 inch TFT Module (GMT020-01) Pin Descriptions

NO.SymbolDescription
1GNDPower Ground
2LEDKLED Cathode
3LEDALED Anode
4VDDPower Supply for Analog
5GNDPower Ground
6D/CDisplay data/command selection pin in 4-line serial interface.
7CSChip selection pin; low enable, high disable.
8SCLThis pin is used to be serial interface clock
9SDASPI interface input/output pin. the data is latched on the rising edge of the SCL signal.
10RESETThis signal will reset the device and it must be applied to properly initialize the chip. Signal is active low.
11GNDPower Ground
2.0 inch TFT LCD Module (GMT020-01) Wiring Diagram
Figure 8: 2.0 inch TFT LCD Module (GMT020-01) Wiring Diagram

4.2. Power Supply Requirements

  • TFT Power Supply (VCC): The screen power supply is typically 2.8-3.3V. Do not use 5V directly unless the module has an integrated 3V regulator IC (some PCB modules allow 5V input).
  • Logic IO Port Voltage: 3.3V (TTL).
  • Backlight Power Supply (LED pin): The maximum backlight power supply is 3.2V. If using a 3.3V power supply, connect a 5 ohm current limiting resistor in series. If using a 5V power supply, connect a 25 ohm resistor in series.

5. Operation

These TFT LCD modules are controlled via a Serial Peripheral Interface (SPI). To operate the display, you will typically need to:

  1. Initialize the Display: Send a sequence of commands to the driver IC (ST7735S or ST7789VW) to configure the display parameters such as resolution, color mode, and orientation.
  2. Send Display Data: Transmit pixel data over the SPI bus. The data/command (DC) pin is used to differentiate between command bytes and data bytes.
  3. Control Backlight: The backlight (BLK) pin can be used to control the display's brightness, often via PWM (Pulse Width Modulation) from your microcontroller.

Refer to the specific driver IC datasheet (ST7735S or ST7789VW) and example code for your microcontroller platform (e.g., Arduino libraries) for detailed programming instructions.

6. Maintenance

  • Handling: Handle the module by its edges to avoid touching the display area or damaging the flexible flat cable (FPC).
  • Cleaning: Use a soft, lint-free cloth, lightly dampened with distilled water or an LCD cleaning solution, to clean the display surface. Avoid harsh chemicals or abrasive materials.
  • Storage: Store the module in a dry, anti-static environment within the specified storage temperature range (-30℃ to 70℃/80℃ depending on model).
  • Power: Always ensure the correct power supply voltage and current limiting resistors for the backlight to prevent damage.

7. Troubleshooting

  • No Display/Blank Screen:
    • Check all wiring connections, especially power (VCC, GND) and SPI pins (SCL, SDA, CS, DC, RES).
    • Verify the power supply voltage is within the specified range (2.8-3.3V for TFT, 3.2V for backlight with appropriate resistors).
    • Ensure the display is properly initialized in your code. The reset (RES) pin must be toggled correctly.
    • Confirm the backlight (BLK) pin is receiving power or a control signal.
  • Incorrect Colors/Garbled Display:
    • Check the SPI data transmission. Ensure data is sent correctly and at the appropriate speed.
    • Verify the display initialization commands match the specific driver IC (ST7735S or ST7789VW) and module configuration.
    • Ensure the correct color format (e.g., RGB 65K) is being used in your software.
  • Display Not Responding:
    • Check if the microcontroller is sending signals to the correct pins.
    • Ensure the chip select (CS) pin is correctly asserted (low) during communication.

8. User Tips

  • When working with these modules, it is highly recommended to use a logic level shifter if your microcontroller operates at 5V and the display requires 3.3V logic, to prevent damage to the display's data pins.
  • Always double-check the pin assignments for your specific module variant, as slight differences can occur between different sizes or batches.
  • Utilize existing open-source libraries (e.g., Adafruit GFX and ST7735/ST7789 libraries for Arduino) as a starting point for your projects. These libraries often handle the complex initialization sequences and drawing functions.

9. Warranty and Support

For technical support, driver code examples, or any inquiries regarding your Estardyn TFT LCD module, please contact the seller or manufacturer directly. Keep your purchase records for any warranty claims.

© 2024 Estardyn. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.