Kyvol Cybovac S60 AICLE INS-200

Contents

Kyvol Cybovac S60 AICLE INS-200 Lidar Unit Instruction Manual

Original Replaceable Maintenance Part for Vacuum Cleaning Robot

1. Important Safety Information

Please read all instructions carefully before using this product. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.

2. Product Overview

This document provides instructions for the original replaceable lidar unit for the Kyvol Cybovac S60 AICLE INS-200 vacuum cleaning robot. The lidar unit is a critical component for the robot's navigation and mapping capabilities.

Top view of the Kyvol Cybovac S60 lidar unit with an orange cover.

Figure 1: Top view of the lidar unit (orange cover).

Top view of the Kyvol Cybovac S60 lidar unit with a blue cover and visible wires.

Figure 2: Top view of the lidar unit (blue cover) with connecting wires.

3. Setup and Installation

Before first use or installation, ensure all protective films are removed from the device.

3.1 Component Identification

Familiarize yourself with the lidar unit's components before installation.

Bottom view of the lidar unit, showing the circuit board, motor, and 'QC PASS' sticker.

Figure 3: Bottom view of the lidar unit, revealing the internal circuit board and motor.

Angled view of the lidar unit's underside, highlighting the circuit board, motor, and wiring connections.

Figure 4: Angled view of the lidar unit's underside, showing the circuit board, motor, and wiring.

Close-up of the lidar unit's circuit board, showing various electronic components, connectors, and a small motor.

Figure 5: Detailed view of the lidar unit's circuit board and motor assembly.

3.2 Installation Procedure

Refer to your Kyvol Cybovac S60 AICLE INS-200 vacuum cleaning robot's main instruction manual for specific steps on how to access and replace the lidar unit. Generally, the process involves:

  1. Power off the robot and disconnect it from any charging source.
  2. Locate the lidar unit compartment, typically on the top of the robot.
  3. Carefully remove any screws or clips securing the old lidar unit.
  4. Disconnect the wiring harness from the old unit.
  5. Connect the new lidar unit's wiring harness to the robot's main board.
  6. Position the new lidar unit in its compartment and secure it with screws or clips.
  7. Ensure all connections are firm and the unit is properly seated.
  8. Close the robot's cover.

Caution: Handle the circuit board and wires with extreme care to avoid damage. If you are unsure about any step, consult a qualified technician.

4. Operating the Lidar Unit (Post-Installation)

Once the new lidar unit is installed, power on your Kyvol Cybovac S60 AICLE INS-200 robot. The robot should automatically detect the new lidar unit and begin its initialization process. Observe the robot's behavior to ensure proper functionality.

  • Initial Scan: Allow the robot to perform an initial scan of its environment to update its internal map.
  • Navigation Test: Run a short cleaning cycle to verify the robot's navigation, obstacle avoidance, and mapping capabilities.
  • App Integration: Check the companion mobile application to confirm that the robot's map is being updated correctly and that no lidar-related errors are reported.

5. Maintenance

Regular maintenance of the lidar unit ensures optimal performance of your vacuum robot.

  • Cleaning the Sensor Window: Periodically wipe the lidar sensor window with a soft, dry cloth to remove dust and debris. Avoid using abrasive materials or harsh chemicals.
  • Inspection: Visually inspect the lidar unit for any signs of physical damage, loose connections, or obstructions.
  • Software Updates: Ensure your robot's firmware is up-to-date, as updates often include improvements for navigation and sensor performance.

6. Troubleshooting

If you encounter issues after installing the new lidar unit, consider the following troubleshooting steps:

Problem Possible Cause Solution
Robot not navigating correctly or getting stuck frequently. Lidar sensor window is dirty or obstructed. Unit not properly installed. Clean the lidar sensor window. Re-check installation to ensure secure connections and proper seating. Restart the robot.
Robot reports a lidar error. Loose connection, faulty unit, or software glitch. Power cycle the robot. Check all wiring connections. If the problem persists, the unit may be faulty and require replacement.
Robot cannot create or update map. Lidar unit not functioning, or environmental interference. Ensure no direct sunlight or highly reflective surfaces are interfering with the lidar. Perform a factory reset of the robot (consult your robot's main manual).

If troubleshooting steps do not resolve the issue, contact customer support for further assistance.

7. Specifications

Feature Detail
Product Name Kyvol Cybovac S60 AICLE INS-200 Lidar Unit
Model Number Kyvol Cybovac S60 AICLE INS-200
Type Vacuum Cleaner Parts (Lidar)
Material Plastic
Vacuum Part Type Filters (as categorized, but functionally a lidar sensor)
Origin Mainland China
Package Weight 0.29 kg
Package Dimensions (L x W x H) 10 cm x 10 cm x 10 cm

8. Warranty and Support

For warranty information and technical support, please refer to the original documentation provided with your Kyvol Cybovac S60 AICLE INS-200 vacuum cleaning robot or contact the manufacturer directly.

Manufacturer Information:

  • Company: Dreame Trading (Tianjin)Co.,Ltd.
  • Address: No. 1688 Songwei Road, Guoxiang Street, Wuzhong Economic Development Zone, Suzhou, Suzhou Jiangsu Province, China
  • Email: admin@dreami.tech

EU Representative Information:

  • Company: La nuit lighting SARL
  • Address: 253 RUE SAINT HONORE Isere Auvergne-Rhone-Alpes, France
  • Email: yldyx112@outlook.com

When contacting support, please have your robot's model number and the lidar unit's batch/serial number (if available) ready.

A user manual in PDF format is available for reference: View User Manual (PDF)

9. User Tips

  • Gentle Handling: The lidar unit contains delicate electronic components. Always handle it with care to prevent damage.
  • Static Electricity: Before handling the lidar unit, discharge any static electricity from your body by touching a grounded metal object.
  • Compatibility: Ensure you have purchased the correct lidar unit model for your specific Kyvol Cybovac S60 AICLE INS-200 robot to guarantee compatibility.
  • Environmental Factors: For optimal lidar performance, avoid operating the robot in environments with strong direct sunlight or highly reflective surfaces, which can interfere with the sensor.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.