BRPOM BM501 4000A Portable Car Jump Starter User Manual

1. Introduction

Thank you for choosing the BRPOM BM501 4000A Portable Car Jump Starter. This device is a versatile emergency tool designed to jump start your vehicle, charge your electronic devices, and provide illumination in various situations. Please read this manual carefully before use to ensure safe and optimal performance.

2. Safety Information

Your safety is paramount. Please observe the following safety guidelines:

• Always ensure the jump starter is fully charged before attempting to jump start a vehicle.
• Do not place the battery starter near a fire source or expose it to extreme heat.
• Ensure proper polarity when connecting the smart clamps to the vehicle battery (Red to positive, Black to negative).
• Avoid short-circuiting the smart clamps. The intelligent connection line includes protection against reverse polarity, short circuit, overdischarge, overheating, overcurrent, overload, and overvoltage.
• Do not attempt to jump start a vehicle if the jump starter or its cables are damaged.
• Keep out of reach of children.
• If the jump starter does not work on the first attempt, wait 3-4 minutes before trying again.
• This device is designed for 12V vehicle batteries only.

3. Package Contents

The BRPOM BM501 package typically includes:

• 1 x BRPOM BM501 Car Jump Starter
• 1 x Smart Jumper Cables
• 1 x USB Type-C Charging Cable
• 1 x High-value EVA Protection Case
• 1 x User Manual

Note: Package contents may vary slightly depending on the specific model variation (e.g., BM150, BM300, BM502, Voltsurge D02, Biuble 2500A). Some models may not include a storage case.

4. Product Overview and Features

The BRPOM BM501 is a powerful 4-in-1 emergency kit:

• Car Jump Starter: 4000A peak current, capable of starting 12V vehicles (up to 10.0L gasoline or 8.0L diesel engines) in seconds.
• Power Bank: 26800mAh capacity with multiple USB outputs, including a QC3.0 fast charging port (75% faster than standard ports), to charge phones, tablets, and other small devices.
• LED Emergency Light: Features 4 modes: lighting, strobe, SOS, and warning, suitable for various scenarios like camping or roadside emergencies.
• Compass: Integrated for navigation during outdoor adventures.

5. Setup and Initial Charging

Before first use, and after each use, ensure your jump starter is fully charged.

1. Connect the provided USB Type-C charging cable to the jump starter's input port.
2. Connect the other end of the USB cable to a suitable USB wall adapter (not included) or car charger.
3. Allow the device to charge completely. The charging time is approximately 6.5 hours.
4. The digital LCD display (if available on your model) will indicate the battery status and charging progress.

6. Operating Instructions

6.1. Jump Starting a Vehicle

Follow these steps to safely jump start your 12V vehicle:

1. Insert the Jumper Cable: Plug the smart jumper cable connector firmly into the jump starter's port.
2. Connect to Car Battery:
   • Attach the RED (+) clamp to the positive terminal of the car battery.
   • Attach the BLACK (-) clamp to the negative terminal of the car battery.

   Ensure the clamps make good contact with the battery terminals. The smart clamps will provide visual and audible feedback if there are incorrect connections or issues.

3. Start the Engine: Go into your vehicle and start the engine.
4. Remove Clamps: Once the vehicle starts, immediately remove the smart clamps from the car battery, then disconnect the jumper cable from the jump starter.

6.2. Using as a Power Bank

The jump starter can charge your electronic devices:

• Connect your device's USB charging cable to one of the jump starter's USB output ports (Output 1: QC3.0, Output 2: 5V/2.4A).
• For models with wireless charging (e.g., BIUBLE 2500A), ensure the "ON/OFF" button is activated and place your compatible smartphone on the designated wireless charging area. For optimal charging, align the device to the center of the jump starter. Note that thick phone cases may affect wireless charging efficiency.
• Some models (e.g., BM300) may feature a 12V/10A DC output (max 160W) for powering car accessories like vacuum cleaners or refrigerators.

6.3. Using the LED Flashlight

The integrated LED flashlight offers four modes:

• Lighting: For general illumination.
• Strobe: A flashing light for signaling or attracting attention.
• SOS: Emits the international Morse code signal for distress.
• Warning: A specific warning light pattern.

Refer to your specific model's manual for instructions on how to cycle through these modes, usually by pressing the power/light button multiple times.

7. Maintenance

Proper maintenance ensures the longevity and reliability of your jump starter:

• Recharge After Use: Always fully recharge the jump starter after each use.
• Regular Charging: If not used for a long period, it is recommended to charge the jump starter once every three months to maintain battery health and prolong its service life.
• Storage: Store the device in a cool, dry place, away from direct sunlight and extreme temperatures. The optimal working temperature range is -20℃ to 60℃ (-4℉ to 140℉).

8. Troubleshooting

If you encounter issues, refer to the following common problems and solutions:

8.1. Red Light On or Beeping from Smart Clamps

This indicates a potential issue with the connection or battery:

1. Check Clamp Connection: Ensure the clamps are connected correctly (Red to positive, Black to negative).
2. Ensure Full Contact: Make sure the clamps have full and clean contact with the battery terminals. Clean any dirt or oil stains from the terminals if necessary.
3. Vehicle Boot Protection: Some cars have a boot protection system. Ensure the car's doors or boot are closed.
4. If the issue persists after checking these points, the vehicle battery might be severely damaged or the jump starter might require service.

8.2. Cannot Jump Start the Vehicle

If the vehicle does not start:

1. Incorrect Voltage: Confirm that the vehicle is a 12V system. This jump starter is not compatible with other voltages.
2. Low Jump Starter Battery: Ensure the jump starter itself is sufficiently charged.
3. Severely Discharged Vehicle Battery: If the vehicle battery has been dormant for a very long time or is completely dead, the jump starter may not be able to revive it.
4. Retry: If the car starter does not work the first time, wait 3-4 minutes and repeat the operation.

9. Specifications

Specifications for the BRPOM BM501 4000A model:

9.1. Model Variations and Key Differences

BRPOM offers several jump starter models with varying specifications:

10. User Tips

• For optimal performance, ensure the jump starter is fully charged before any trip, especially if you anticipate needing it.
• If your car has been dormant for an extended period, it might require multiple attempts or may not be suitable for jump starting with this device if the battery is severely degraded.
• The user manual is available in multiple languages.

11. Warranty and Support

Most BRPOM jump starter models come with a 2-year warranty. If you encounter any problems with your product, please contact customer service for assistance. They are available to help resolve issues and provide support.