MiBoxer FUT106ZR

Contents

MiBoxer FUT106ZR Smart GU10 RGB+CCT LED Spotlight User Manual

Model: FUT106ZR | Brand: MiBoxer

1. Introduction

Thank you for choosing the MiBoxer FUT106ZR Smart GU10 RGB+CCT LED Spotlight. This product integrates Zigbee 3.0 and 2.4G RF wireless technologies, offering a wide range of lighting possibilities including 16 million colors, adjustable color temperature, and dimmable brightness. It supports various control methods including 2.4G RF remote, Tuya Smart App, Philips Hue, Amazon Alexa, Google Home, and DMX512 (additional gateway/transmitter required for some functions). Please read this manual carefully before installation and operation to ensure proper use and optimal performance.

2. Safety Information

  • Ensure the power is OFF before installation or maintenance.
  • Do not install in wet environments or near heat sources.
  • This product is designed for indoor use only.
  • Do not disassemble or modify the product.
  • Use only with compatible GU10 fixtures and appropriate voltage (AC100-240V).
  • Keep out of reach of children.

3. Product Features

  • Dual Wireless Control: Supports Zigbee 3.0 standard protocol and 2.4G RF remote control.
  • Full Color & White Control: 16 Million colors to choose from (RGB) and adjustable color temperature (CCT) from 2700K to 6500K.
  • Dimmable: Brightness and saturation are fully adjustable.
  • Smart Device Integration: Compatible with Tuya Smart App, Philips Hue, Amazon Alexa, and Google Home (Zigbee 3.0 gateway required for app/voice control).
  • DMX512 Controllable: Requires an additional DMX512 LED transmitter for control.
  • Auto-Transmitting & Synchronization: One lighting fixture can transmit signals from the remote to another within 30m. Multiple fixtures can synchronize dynamic modes when controlled by the same remote within 30m.
  • Customization: Supports multiple scene customization, group control, device sharing, timing settings, and Tap-to-Run automation.
  • "Do Not Disturb" Mode: Prevents the light from turning on automatically after a power outage (default activated).
MiBoxer FUT106ZR Product Features Overview

Image: Overview of MiBoxer FUT106ZR key features including color options, dimming, and smart control compatibility.

4. Specifications

ParameterValue
Product Name6W GU10 RGB+CCT LED Spotlight (Zigbee 3.0 + 2.4G)
Model No.FUT106ZR
Input VoltageAC100-240V~ 50/60Hz
Power6W
PF>0.55
CRI>80
Color Temperature2700K~6500K
Luminous Flux550LM
Luminous Efficiency90LM/W
Beam Angle30°
Communication ProtocolZigbee 3.0 + 2.4GHz
Control DistanceZigbee: 50m (open area), 2.4G RF Remote: 30m
IP Rate-
Working Temperature-10~40°C
Wireless TechnologyZigbee 802.15.4
Wireless Frequency2.400-2.480GHz
Base TypeGU10
MiBoxer FUT106ZR Product Parameters and Dimensions

Image: Detailed product parameters, dimensions, and packaging information.

5. Setup and Installation

5.1 General Installation

  1. Ensure the power supply to the GU10 fixture is turned off.
  2. Carefully insert the FUT106ZR spotlight into the GU10 socket.
  3. Twist to secure the bulb in place.
  4. Restore power to the fixture.

5.2 2.4G RF Remote Control Instructions

The FUT106ZR spotlight is compatible with various Mi-Light / MiBoxer 2.4GHz series remotes (purchased separately). Refer to the image below for compatible remote models.

Compatible 2.4G RF Remote Controls

Image: Various compatible 2.4G RF remote controls for the MiBoxer spotlight.

5.2.1 Linking Code Instructions

  1. Power off the light, then power it on again after 10 seconds.
  2. Within 3 seconds of powering on, short press the "I" button on the remote control 3 times.
  3. The light will blink 3 times slowly, indicating successful linking.

Attention: If linking failed (light is not blinking slowly), please follow the above steps again. A light that has already been linked cannot be linked again.

5.2.2 Unlinking Code Instructions

  1. Power off the light, then power it on again after 10 seconds.
  2. Within 3 seconds of powering on, short press the "I" button on the remote control 5 times.
  3. The light will blink 10 times quickly, indicating successful unlinking.

Attention: If unlinking failed (light is not blinking quickly), please follow the above steps again. Lights that haven't been linked do not need to be unlinked.

2.4G RF Remote Control Linking and Unlinking Instructions

Image: Visual guide for linking and unlinking the spotlight with a 2.4G RF remote control.

5.3 Smartphone APP Control (Tuya Smart)

Note: Using APP control requires an additional purchase of a Zigbee 3.0 gateway.

  1. Connect the spotlight with power supply.
  2. Ensure the light is in pairing network mode (factory default is pairing network). You can achieve this by:
    • Way One: Turn off and turn on the light 3 times or over 3 times continuously. The light will enter a breathing status.
    • Way Two: Long press the "SET" key on a compatible remote until the indicator light flashes.
  3. Open the "Tuya Smart" App on your smartphone.
  4. Navigate to the Zigbee gateway within the app and click "Add sub device".
  5. Confirm that the indicator light on the spotlight is flashing quickly.
  6. Follow the in-app instructions to complete the configuration.
Tuya Smart App Control Setup Instructions

Image: Screenshots guiding through the Tuya Smart App setup process for the spotlight.

5.4 Philips Hue Control

  1. Connect the spotlight with power supply.
  2. Ensure the light is in pairing network mode (factory default is pairing network). You can achieve this by:
    • Way One: Turn off and turn on the light 3 times or over 3 times continuously. The light will enter a breathing status.
    • Way Two: Long press the "SET" key on a compatible remote until the indicator light flashes.
  3. Open the "Philips Hue" App.
  4. Click "SETTINGS", then navigate to "Lights".
  5. Click the "+" icon on the top right corner to add a new light.
  6. Click "Search".
  7. Click "Start configuration" and follow the app instructions to complete the pairing.
Philips Hue Control Setup Instructions

Image: Screenshots illustrating the Philips Hue app setup for the spotlight.

5.5 Alexa Voice Control

5.5.1 For Amazon Echo devices with built-in Zigbee 3.0 protocol support:

  1. Connect the spotlight with power supply.
  2. Ensure the light is in pairing network mode (factory default is pairing network). You can achieve this by:
    • Way One: Turn off and turn on the light 3 times or over 3 times continuously. The light will enter a breathing status.
    • Way Two: Long press the "SET" key on a compatible remote until the indicator light flashes.
  3. Say to your Amazon Echo device: "Alexa, Discover devices".
  4. Wait for Alexa to discover the device and activate voice control.

5.5.2 For Amazon Echo devices without built-in Zigbee 3.0 protocol support:

Note: This method requires an additional MiBoxer Zigbee 3.0 gateway.

  1. Open the Alexa App.
  2. Click "More" on the bottom right corner, then select "Skills & Games".
  3. Search for "Smart life".
  4. Click on the "Smart Life" skill and follow the instructions to enable it and link your Smart Life account (where your MiBoxer gateway and spotlight are configured).
  5. Once linked, you can use voice commands to control your spotlight.
Alexa Voice Control Setup Instructions

Image: Screenshots detailing Alexa voice control setup for both direct Zigbee and gateway-dependent methods.

5.6 Google Home Voice Control

Note: This method requires an additional MiBoxer Zigbee 3.0 gateway.

  1. Open the Google Home App.
  2. Click the "+" icon on the top left corner.
  3. Select "Set up device".
  4. Choose "Works with Google".
  5. Click the search icon (magnifying glass) on the top right corner.
  6. Type "Smart life" and search.
  7. Click on the "Smart Life" skill and follow the instructions to link your Smart Life account (where your MiBoxer gateway and spotlight are configured).
  8. Once linked, you can use voice commands to control your spotlight.
Google Home Voice Control Setup Instructions

Image: Screenshots guiding through the Google Home app setup for the spotlight.

5.7 DMX512 LED Transmitter Control

Note: This function requires an additional DMX512 LED transmitter (e.g., FUTD01), purchased separately.

5.7.1 Linking with DMX512 Transmitter

  1. Follow the instructions provided with your DMX512 transmitter (e.g., FUTD01) to set up the desired zone (e.g., CH12).
  2. Power off the spotlight, then power it on again after 10 seconds.
  3. When the light is ON, short press the "I" button on the DMX512 transmitter 3 times within 3 seconds.
  4. The light will blink 3 times slowly, indicating successful linking.

5.7.2 Unlinking from DMX512 Transmitter

  1. Power off the spotlight, then power it on again after 10 seconds.
  2. When the light is ON, short press the "I" button on the DMX512 transmitter 5 times within 3 seconds.
  3. The light will blink 10 times quickly, indicating successful unlinking.

Attention: If linking or unlinking failed, please follow the above steps again.

DMX512 LED Transmitter Control Link/Unlink Diagram

Image: Diagram showing DMX512 LED transmitter control and link/unlink process.

6. Operating Instructions

6.1 Color, Brightness, and Color Temperature Adjustment

Once linked to a remote or smart app, you can adjust the following:

  • 16 Million Colors: Select any color from the RGB spectrum.
  • Color Temperature: Adjust from warm white (2700K) to cool white (6500K).
  • Brightness: Dim or brighten the light output.
  • Saturation: Adjust the intensity of the color.

Refer to your specific remote control or smart app interface for detailed instructions on how to make these adjustments.

2.4GHz RF Remote Control Features

Image: Features of 2.4GHz RF remote control including color, saturation, color temperature, and brightness adjustment.

6.2 Dynamic Modes (Remote Control Only)

The spotlight offers various dynamic modes for different lighting effects. These modes are primarily controlled via the 2.4G RF remote.

6.2.1 Selecting Dynamic Mode Table 1 (Default)

While the light is in static mode, short press the "S+" button on your remote control 5 times quickly until the blue light flashes 3 times slowly. This activates Dynamic Mode Table 1.

6.2.2 Selecting Dynamic Mode Table 2 (Manual Switch)

While the light is in static mode, short press the "S-" button on your remote control 5 times quickly until the yellow light flashes 3 times slowly. This activates Dynamic Mode Table 2.

NumberDynamic Mode (Table 1 - Default)Brightness / Saturation / Speed
1Mardi GrasAdjustable
2Automatic color change
3Sam
4Gemstone
5Twilight
6American
7Fat Tuesday
8Party
9Slow Color Splash
NumberDynamic Mode (Table 2 - Need to switch manually)Brightness / Saturation / Speed
1Seven colors gradual changeAdjustable
2White light gradual change
3RGB gradual change
4Seven colors jump to change
5Jump to change randomly
6Red light gradual change + Flash 3 times
7Green light gradual change + Flash 3 times
8Blue light gradual change + Flash 3 times
9White light gradual change + Flash 3 times
Dynamic Mode Tables for Remote Control

Image: Tables listing dynamic modes available via remote control.

6.3 Auto Transmitting & Synchronization

The FUT106ZR spotlight features signal auto-transmitting. One lighting fixture can transmit the signals from the remote control to another lighting fixture within 30m, as long as there is a lighting fixture within 30m, the remote control distance can be limitless.

Different lighting fixtures can work synchronously when they are started at different times, controlled by the same remote, under the same dynamic mode and within 30m distance.

Auto Transmitting and Modes Synchronization Diagram

Image: Diagram illustrating signal transmitting and modes synchronization between multiple lighting fixtures.

6.4 "Do Not Disturb" Mode

This mode is activated by default to prevent the light from turning on automatically after a power outage. This is particularly useful in areas with frequent power outages to save energy.

6.4.1 Turn On/Off via 2.4G RF Remote

  • To Activate "Do Not Disturb" mode: Press the "OFF" button on the remote control 3 times within 3 seconds. The light will flash 4 times quickly, indicating activation.
  • To Turn Off "Do Not Disturb" mode: Press the "ON" button on the remote control 3 times within 3 seconds. The light will flash 4 times slowly, indicating deactivation.

Attention: If the light is OFF, it needs to be powered on 2 times before the light will light up. If the light is ON, turn off and turn on power one time. The light will always be "ON" if you turn on and turn off power once the user has closed "Do Not Disturb" mode.

6.4.2 App Control for "Do Not Disturb" Mode

Refer to the Smartphone APP control instructions (Section 5.3) for details on how to manage "Do Not Disturb" mode through the Tuya Smart App.

7. Maintenance

  • Cleaning: Ensure the power is off before cleaning. Use a soft, dry cloth to wipe the surface of the spotlight. Do not use abrasive cleaners or solvents.
  • Storage: If storing the spotlight for an extended period, keep it in a cool, dry place away from direct sunlight and extreme temperatures.
  • Regular Checks: Periodically check the bulb for any signs of damage or loose connections.

8. Troubleshooting

  • Light does not turn on:
    • Check if the power supply is connected and switched on.
    • Ensure the bulb is correctly installed in the GU10 socket.
    • Verify the voltage supply is within the specified range (AC100-240V).
  • Remote control not working:
    • Ensure the remote has fresh batteries.
    • Re-link the spotlight to the remote control following the instructions in Section 5.2.1.
    • Ensure the remote is within the 30m control distance.
  • App control not working:
    • Verify that the Zigbee 3.0 gateway is powered on and connected to your network.
    • Ensure the spotlight is successfully paired with the Zigbee 3.0 gateway and added to the app.
    • Check your Wi-Fi connection and ensure your smartphone is connected to the internet.
    • Restart the app and try again.
  • Linking/Unlinking failed:
    • Ensure you are following the exact timing and button press sequence (3 times for linking, 5 times for unlinking) within 3 seconds after powering on.
    • Make sure the light is in the correct state (unlinked for linking, linked for unlinking).
  • Light does not respond to commands after power outage:
    • If "Do Not Disturb" mode is active, the light needs to be powered on 2 times before it will light up.
    • If "Do Not Disturb" mode was deactivated, the light should turn on automatically. If not, check power supply and linking.

9. User Tips

  • Gateway Requirement: Remember that a Zigbee 3.0 gateway is essential for smartphone app control and voice assistant integration (Alexa, Google Home, Philips Hue). Plan to purchase one if you intend to use these smart features.
  • Remote Control Range: While the remote has a 30m direct range, the auto-transmitting feature allows for a theoretically limitless range as long as there are other linked lights within 30m to relay the signal. Position your lights strategically for optimal coverage.
  • Dynamic Modes: Experiment with both Dynamic Mode Table 1 and Table 2 to find the lighting effects that best suit your mood or occasion.

10. Warranty and Support

This product comes with a standard manufacturer's warranty. For specific warranty terms and conditions, please refer to the product packaging or contact your retailer. For technical support or further assistance, please contact the seller or MiBoxer customer service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.