Introduction
This manual provides comprehensive instructions for the safe and efficient use of your BTF-LIGHTING Metal Touch Sensor Switch LED Dimmer. This device is designed to control single-color LED lighting products, allowing for seamless on/off functionality and brightness adjustment from 0% to 100% without flickering. Please read this manual thoroughly before installation and operation.
Image: Front view of the Metal Touch Sensor Switch LED Dimmer with DC connectors.
Specifications
| Feature | Detail |
|---|---|
| Item Type | Metal Touch Sensor Switch (LED Dimmer) |
| Voltage | DC12V / DC24V |
| Max Load Current | 3A |
| Wattage | 12V 36W / 24V 72W |
| Power Source | DC |
| Connection Mode | DC Connector Plug (5.5*2.1mm) |
| Cable Length | 14cm / 18cm |
| Working Temperature | -20ºC ~ 60ºC |
| Material | Metal Case |
| Applicable Lights | 2pin LED Strip Lights (single color) |
| Control Method | Touch Sensor |
| Certifications | CE, FCC, ROHS |
Image: Detailed dimensions of the dimmer switch and its DC connectors.
Image: Examples of supported LED lighting products including strip lights, recessed lights, chandeliers, and more.
Setup and Installation
Follow these steps for proper installation of your LED dimmer switch:
- Power Source: Ensure your power source (LED Driver) matches the required DC12V or DC24V voltage for your LED strip.
- Connect Input: Connect the input DC plug (5.5mm outer diameter, 2.1mm inner diameter) of the dimmer switch to your DC power adapter/LED driver.
- Connect Output: Connect the output DC plug (2.1mm outer diameter, 5.5mm inner diameter) of the dimmer switch to your single-color LED strip lights.
- Secure Placement: The dimmer switch can be installed using double-sided tape on a non-metallic surface. Ensure the touch sensor area is easily accessible.
Image: Correct wiring diagram showing connection from AC input to LED driver, then to the dimmer switch, and finally to the LED strip.
Image: Illustration of installing the dimmer switch using double-sided tape on a surface.
Important Installation Notes:
- DO NOT wire the device backwards. Incorrect wiring can lead to overheating and short-circuiting of the controller.
- The mini touch dimmer switch controller cannot be placed on a metal surface or held in your hand for dimming, as this may interfere with its touch sensitivity and functionality.
Image: Diagram illustrating correct vs. incorrect wiring to prevent damage.
Image: Visual warning against holding the dimmer or placing it on a metal surface during operation.
Operating Instructions
The Metal Touch Sensor Switch LED Dimmer is operated by touching its metal body:
- On/Off Function: A short touch (less than 5 seconds) on the metal body will toggle the LED lights on or off.
- Dimming Function: A long touch (more than 5 seconds) on the metal body will activate the dimming function. The brightness will continuously adjust, either increasing to 100% or decreasing to 0%. Release your finger when the desired brightness level is reached.
Image: Visual guide demonstrating short press for on/off and long press for 10%-100% brightness adjustment.
The dimmer provides soft and stable light adjustment without flickering, enhancing the ambiance of your space.
Image: Example of the dimmer switch controlling LED strip lights in a living room, showcasing adjustable brightness.
Maintenance
The BTF-LIGHTING Metal Touch Sensor Switch LED Dimmer requires minimal maintenance. Keep the device clean and free from dust. Do not use abrasive cleaners or solvents. Ensure the touch surface is clear of obstructions for optimal performance.
Troubleshooting
- Lights not turning on/off or dimming:
- Check all connections to ensure they are secure and correctly wired (input to power, output to LED strip). Refer to the "Setup and Installation" section for correct wiring.
- Verify that the power source (LED driver) is providing the correct voltage (DC12V or DC24V) and is functioning properly.
- Ensure the LED strip lights are compatible with the dimmer (single color, 2-pin) and are not faulty.
- Confirm that the dimmer is not placed on a metal surface or being held in hand during operation, as this can interfere with the touch sensor.
- Dimmer overheating or short-circuiting:
- Immediately disconnect power. This is often caused by incorrect wiring, particularly wiring the input and output backwards. Re-check wiring according to the installation diagram.
- Ensure the total wattage of your LED lights does not exceed the dimmer's maximum load (36W for 12V, 72W for 24V). Overloading can cause overheating.
User Tips
- For optimal performance, mount the dimmer in an easily accessible location where the touch sensor is not obstructed.
- Consider the aesthetic integration of the dimmer. Its compact size allows for discreet placement in cabinets, under shelves, or behind furniture.
- If controlling a very long LED strip or multiple strips, ensure the total wattage does not exceed the dimmer's capacity. For larger installations, consider using an amplifier in conjunction with the dimmer.
Warranty and Support
This BTF-LIGHTING Metal Touch Sensor Switch LED Dimmer comes with a 2-year warranty from the date of purchase, covering manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.
For technical support, troubleshooting assistance, or warranty inquiries, please contact BTF-LIGHTING customer service through your retailer or the official BTF-LIGHTING website.
