Introduction
Thank you for choosing the HITBOX HIM250DPP welding machine. Our welders are engineered with high-quality components and undergo rigorous lab tests to ensure superior welding experience and performance. For your safety and to ensure optimal operation, please read and understand this manual thoroughly before using the product. Your satisfaction is our priority.
1. Safety Precautions
WARNING: Welding can cause serious injury or death. Always take protective measures.
- Electric Shock: Can cause serious injury or death. Install proper grounding devices. Do not touch energized parts with bare skin or wet gloves. Ensure insulation from the floor and workpiece.
- Smoke and Fumes: Can damage your health. Keep your head away from fumes. Ensure a well-ventilated work environment with exhaust fans or ventilation equipment.
- Arc Radiation: May injure eyes and burn skin. Use appropriate welding masks and protective clothing. Protect onlookers with masks or curtains.
- High Temperature Workpieces: Can cause severe burns. Do not touch hot workpieces with bare hands. Allow the torch to cool after continuous work.
- Excessive Noise: Can damage hearing. Wear ear muffs or other hearing protection. Warn bystanders of noise hazards.
- Magnetic Fields: Can affect pacemakers. Individuals with pacemakers should consult a doctor before welding.
- Moving Parts: Can cause injury. Keep away from moving parts (e.g., fans). Ensure all protective devices (doors, panels, covers) are properly closed.
- Replacing Components: Only specialized personnel should replace machine parts. Ensure no foreign objects are left inside after replacement. Verify internal connections are correct before operation.
- Disposal: Dispose of the machine as industrial waste. Burning electrolytic capacitors or plastic parts can cause explosions or toxic fumes.
1.1 Working Environment
- The installation site must support the welding machine's weight.
- Avoid areas where water may splash.
- Operate in a dry environment with humidity not exceeding 90%.
- Ambient temperature should be between -10°C and 40°C.
- Do not weld in direct sunlight or rain.
- Avoid dusty or corrosive chemical gas environments.
- Gas-shielded arc welding requires an environment free from strong air currents.
- Do not weld on platforms with a slope exceeding 10°.
1.2 Security Tips
The machine features over-current and over-heat protection. It will automatically shut down if output current or internal temperature exceeds set standards. To prevent damage:
- Good Ventilation: The internal fan is crucial for cooling. Ensure shutters are not obstructed. Maintain a minimum distance of 30 cm from nearby objects.
- Avoid Overloading: Operate within the permitted duty cycle. Do not exceed the maximum load current to prevent shortening the machine's service life.
- Avoid Overvoltage: The machine has automatic voltage compensation. However, exceeding permissible supply voltage can damage the machine.
1.3 Description of Symbols
- ! WARNING: Matters calling for attention.
- : Objects requiring special description and identification.
- : It is prohibited to dispose of electrical waste with other common wastes. Please protect the environment.
2. Product Overview
The HITBOX HIM250DPP welding machine features a unique electrical structure and air channel design that enhances heat dissipation and improves the machine's duty cycle. The air channel cooling system protects power devices and control circuits from dust, significantly improving reliability.

3. Functional Overview
The HIM250DPP offers versatile welding capabilities and advanced features:
- Synergy MIG: Automatically matches voltage and current by adjusting wire diameter, material, and wire feed speed.
- 8-in-1 Versatility: Supports Gas MIG, Gasless MIG, MMA, TIG, Single Pulse MIG, Double Pulse MIG, and Spot Welding.
- 2T/4T: Enables easy welding and long-term continuous welding for a wide range of applications.
- Inductance Regulation: Improves soldering performance.
- Wire Feed Speed Adjustment: Meets various welding requirements.
- VRD (Voltage Reduction Device): Reduces electric shock risk and ensures operator safety.
- Voltage Regulation: Allows increasing and decreasing the depth of dissolution.
- Peak Pulse Current Regulation: Improves welding results and reduces heat.
- Pulse Frequency Regulation: Reduces spark spatter.
- Precise Preset Parameters: Parameters can be set for each welding mode.
- Hot Start: Facilitates arc ignition in MMA welding.
- Arc Force: Improves machine performance and aids long-distance welding.
- Anti-sticking: Improves welding performance and prevents electrode sticking.
- System Language: English, German, Russian, and Chinese options available.

4. Performance Characteristics
The HIM250DPP incorporates advanced IGBT inverter technology for efficient and stable welding.
- Advanced IGBT Inverter Technology: The 43 KHz inversion frequency reduces size and weight, minimizes copper and iron losses, and improves welding efficiency. The high switching frequency eliminates noise pollution.
- Pulse Function: Ensures good arc initiation, reduces heat-affected zone, minimizes distortion, and is ideal for thin metal workpieces. Melting efficiency for space welds is approximately 25% higher than DC welding.
- Leading Control Mode: Advanced digital control improves welding performance. Suitable for wire diameters of 0.6-1.0 mm and various electrode types. Provides easy arc point, less splash, stable current, and a beautiful weld appearance. The cooling fan operates only when needed, prolonging service life.
- Beautiful Shape and Structural Design: Streamlined front and rear panels. Features a 4.3" LED digital display for easy data reading. Panels are made of sturdy engineering plastics for durability in harsh conditions.
5. Technical Specifications
5.1 Basic Parameters
| Technical Parameters | Unit | AC110V±15 (50/60HZ) | AC220V±15 (50/60HZ) |
|---|---|---|---|
| Rated Input Voltage | V | AC110V±15 | AC220V±15 |
| Rated Input Power | KVA | 4.5 | 7.5 |
| Rated Input Current | A | 41A | 34 |
| Welding Current Range (MMA) | A | 20-120 | 20-180 |
| Welding Current Range (TIG) | A | 15-180 | 15-200 |
| Welding Voltage Range (MIG) | V | 16.5-22 | 16.5-24 |
| Wire Feed Speed Range | meters/minute | 11 | 12.5 |
| Rated Duty Cycle | % | 60 | 60 |
| Open Circuit Voltage | V | 69 | |
| Overall Efficiency | % | 85 | |
| Enclosure Class | IP | 21S | |
| Power Factor | 0.73 | ||
| Insulation Class | H | ||
| Standard | UL60974-1 | ||
| Dimensions | mm/inch | 530 x 410 x 210 mm (20.87 x 16.14 x 8.27 inches) | |
| Weight | kg/lb | 16.8 kg (37.04 lb) | |
| Applicable Electrodes | 1.6-3.2 (1/16"-1/8") | 1.6-4.0 (1/16"-5/32") | |
| Applicable Wires | mm/inch | 0.6/0.8/0.9/1.0/1.2 | 0.6/0.8/0.9/1.0/1.2 |
5.2 MMA Welding Parameters
| Technical Parameters | Unit | AC110V±15 (50/60HZ) | AC220V±15 (50/60HZ) |
|---|---|---|---|
| Welding Current Range (MMA) | A | 20-180 | 20-180 |
| Welding Current Range (TIG) | A | 20-180 | 20-180 |
| Hot Start | A | 0-100 | |
| Arc Thrust | A | 0-100 | |
5.3 MIG Welding Parameters
| Technical Parameters | Unit | AC110V±15 (50/60HZ) | AC220V±15 (50/60HZ) |
|---|---|---|---|
| Welding Current Range (MIG) | A | 50-160 | 50-200 |
| Applicable Wires | MM | 0.8/0.9/1.0 | 0.6/0.8/0.9/1.0 |
| Welding Mode | 2T/4T/Spot | ||
5.4 Single Pulse MIG Welding Parameters
| Technical Parameters | Unit | AC110V±15 (50/60HZ) | AC220V±15 (50/60HZ) |
|---|---|---|---|
| Welding Current Range (MIG) | A | 24-141 | 24-200 |
| Applicable Wires | MM | 0.8/1.0/1.2 | |
| Welding Mode | 2T/4T/Spot | ||
| Inductive Effect | -50%-50% (usually 0) | ||
| Voltage Regulation Range | -50%-50% | ||
| Duty Cycle | 20%-80% (usually 50%) | ||
| Pulse Frequency | 0.5 Hz-5 Hz (usually 1.5 Hz) | ||
| Base Current (Physics) | 30%-85% | ||
| Peak Current | Same as set current value | ||
5.5 Dual Pulse MIG Welding Parameters
| Technical Parameters | Unit | AC110V±15 (50/60HZ) | AC220V±15 (50/60HZ) |
|---|---|---|---|
| Welding Current Range (MIG) | A | 24-151 | 24-200 |
| Applicable Wires | MM | 0.8/1.0 | 1.0/1.2 |
| Welding Mode | 2T/4T/Spot | ||
| Inductive Effect | -50%-50% | ||

6. Setup (Installation, Commissioning, and Operation)
Before making any electrical connections, ensure the power switch on the distribution box is turned off. The machine has an IP21S protection rating, so do not use it in the rain.
6.1 Multi-Function Panels Overview


6.2 MMA Welding Installation and Operation
- Connect the primary power cable to the appropriate voltage level (AC110V or AC220V).
- Ensure the mains cable is tightly connected to prevent oxidation.
- Use a multimeter to verify voltage is within acceptable limits.
- Insert the cable plug with the electrode holder into the "-" socket on the front panel and tighten clockwise.
- Insert the cable plug with the grounding clip into the "+" socket on the front panel and tighten clockwise.
- Ensure a proper ground connection for safety.
- After installation, turn on the power switch.
- Pay attention to polarity: DCNP (workpiece to "+", seat to "-") or DCEP (workpiece to "-", seat to "+"). Incorrect polarity can cause unstable arcs.
- When MMA mode is selected, the fan operates, and welding can be performed within the rated output current range.
- Adjust hot start and arc thrust parameters as needed.
- If using long secondary cables, select a larger cross-section to minimize voltage drop.
6.3 Gas MIG Welding Installation and Operation
- Plug the MIG torch into the European standard MIG torch connector on the front panel and tighten.
- Connect the gas cylinder with the gas regulator to the gas inlet on the rear panel using a gas hose.
- Insert the cable plug with the ground clamp into the "-" output terminal on the front panel and tighten clockwise.
- Insert the front panel quick plug into the "+" output terminal and tighten clockwise.
- Install the wire spool onto the spindle adapter. Ensure the wire feed roller groove size matches the gun contact size and wire diameter. Release the wire feed.
- Select the desired MIG/Pulse MIG mode and enter the parameter setting screen.
- Set welding mode, material, wire diameter, and adjust wire feeding speed. Wait a few seconds, then press the voltage adjustment button to start welding.

6.4 Gasless MIG Welding Installation and Operation
- Plug the MIG torch into the European standard MIG torch connector on the front panel and tighten.
- Connect the gas cylinder with the gas regulator to the gas inlet on the rear panel using a gas hose (if applicable for other modes, not for gasless).
- Insert the cable plug with the ground clamp into the "+" output terminal on the front panel and tighten clockwise.
- Insert the front panel quick plug into the "-" output terminal and tighten clockwise.
- Install the wire spool onto the spindle adapter. Ensure the wire feed roller groove size matches the gun contact size and wire diameter. Release the wire feed.
- Thread the wire through the liner into the roll groove and then into the liner of the center connector. Adjust pressure to prevent wire distortion. Press the "Thread" button to feed wire through the torch contacts.
- Operation is similar to Gas MIG.

6.5 Lift TIG Welding Installation and Operation
- Connect the TIG torch to the negative terminal on the front panel and the workpiece to the positive terminal. Ensure quick connectors are tightened.
- Connect the gas inlet hose from the argon cylinder to the TIG gun. Open the gas valve for proper gas flow. (Note: TIG welding gas is not controlled by the machine's built-in valve; connect externally).
- After installation, turn on the power switch. The digital display will turn on, and the fan will operate.
- Select "TIG" as the welding mode.
- Adjust the "Current Adjustment Knob" to select the welding current based on workpiece thickness. Press the torch trigger to start welding.
- Arc Starting Method: For touch start TIG welding, touch the tungsten wire to the workpiece, then lift the torch slightly to initiate normal welding.

6.6 Wire Feeding

7. Operating Functions and Controls
7.1 Detailed Functional Description
The HIM250DPP features a clear liquid crystal display for easy parameter adjustment and mode selection.


7.2 System Parameterization (MIG Mode)
Use the 'SET' and 'ADJUST' knobs to navigate and modify parameters.
- SET Knob: Click to switch language or select welding parameters. Rotate to select different parameters.
- Main Function Buttons: Return to main menu or select welding function.
- ADJUST Knob: Adjust welding parameter values. Press to start welding according to set value.
| No. | Function Parameter | Default | Setting Range | Unit | Description |
|---|---|---|---|---|---|
| 1 | Welding Mode | 2T | 2T/4T/SPOT | Change Welding Mode | |
| 2 | Wire Feed Speed | 5 | 1.5-12.5 | M/min | Changing the wire feed speed |
| 3 | Welding Voltage | 19.5 | 11.0-30.0 | V | Adjustable from -50% to 50% depending on wire feed speed |
| 4 | Inductance | 8 | -50%-50% | Adjusting the level of sparks flying | |
| 5 | Spot Time | 0.5 | 0.5-10 | S | Time control of spot welding |
| 6 | Interval Time | 0 | 0-10 | S |
7.3 Modes of Operation Diagrams



8. Basic Knowledge of Welding
8.1 Basic of MMA (Manual Metal Arc) Welding
MMA welding is an arc welding process using a manually operated electrode. It is simple, convenient, and highly adaptable, suitable for various metal materials thicker than 2mm, especially for complex structures and short weld joints.
8.1.1 Welding Process of MMA
Connect the welder's output terminals to the workpiece and electrode holder. Clamp the electrode. Arc is ignited between the electrode and workpiece, fusing them to form a weld crater. The electrode coating produces slag to cover the weld crater, which forms a slag crust to protect the weld joint. After cooling, the slag crust is removed.
8.1.2 Tools for MMA
- Electrode Holder: For clamping electrodes and conducting current (e.g., 300A or 500A types).
- Welding Mask: Shields eyes and face from arc and spatter. Features colored chemical glass to filter UV/IR rays and allow viewing of the weld crater.
- Slag Hammer (Peen Hammer): Used to remove slag crust from the weld joint surface.
- Wire Brush: For removing dirt, rust, and spatter from workpiece joints and weld surfaces.
- Welding Cable: Connects the electrode holder to the machine (live wire) and the machine to the workpiece (earth wire).
8.1.3 Basic Operation of MMA
- Welding Joint Cleaning: Remove rust and greasy dirt using a wire brush or grinding wheel.
- Posture in Operating: Maintain a stable posture, typically standing to the right of the weld joint, with the mask in the left hand and electrode holder in the right.
- Arc Igniting: Produce a stable arc by scraping or lightly striking the workpiece with the electrode, then lifting it 2-4mm away. If ignition fails, remove any coating from the electrode tip.
- Tack Weld: Weld short joints (30-40mm) at intervals to fix workpiece positions before main welding.
- Electrode Manipulation: Involves moving the electrode along the welding direction, towards the weld crater, and transversely swinging it. Control welding angle (70-80° incline), arc length (equal to electrode diameter), and welding speed for optimal bead appearance and penetration.
- Arc Extinguishing: Gradually pull the electrode away from the groove to narrow the weld crater and reduce metal/heat. Pile up weld metal in the crater to prevent defects.
- Weldment Cleaning: Clean welding slag and spatter with a wire brush after welding.
8.2 GMAW (Gas Metal Arc Welding)
GMAW uses gas as the arc medium and for protecting the arc and welding zone. It is a highly productive open arc welding method, widely applicable to various metals and alloys, including carbon steel, low alloy steel, stainless steel, aluminum, copper, and magnesium alloys.
8.2.1 Classification and Application of GMAW
GMAW can be classified by shield gas, wire form, and operation mode. It is suitable for most metals and alloys, especially those with high melting points. Minimum welding thickness is 1mm. It offers high adaptability to various welding positions.
8.2.2 Welding Equipment for GMAW
- Welding Source: Typically a DC welding source, with power depending on the desired current range.
- Wire Feed System: Consists of a wire feeder (motor, reducer, wheels), wire feed hose, and spool.
- Welding Torch: Can be semi-automatic or automatic, and air-cooled or water-cooled.
8.2.3 Basic Operation of GMAW
- Preweld Cleaning: Chemical cleaning (material-dependent) and mechanical cleaning (sanding, scraping, sand blasting) to remove oxidation film.
- Equipment Check: Inspect for damage, ensure all components are present, and verify correct connections, grounding, and capacity.
- Labor Protection: Wear masks, protective gloves, footwear, and overalls. Use rubber overshoes in wet conditions. Protect against dust, electric shock, scalding, fire, and radiation.
- Welding Parameter Selecting: Parameters include welding current, voltage, speed, stick-out, wire angle, wire diameter, position, polarity, and shield gas flow.
- Current and Welding Voltage: Choose wire diameter based on workpiece thickness, then set current, metal transfer mode, and arc voltage.
- Welding Speed: Affects penetration and weld bead shape. Slower speed increases penetration.
- Stick-out: Proper stick-out (approx. 10 times wire diameter) prevents easy burning of the contact tip and ensures proper melting.
- Position of Welding Wire: The traveling angle (5-15° generally, 25° for maximum penetration) and working angle (45° for horizontal fillet welds) affect weld bead shape and penetration.
- Welding Position: GMAW is applicable to flat, vertical, overhead, and inclined positions.
- Gas Flow: Nozzle diameter (12mm) and gas flow (8-15L/min) are important for shield gas.
- Arc Igniting: Use contact-short arc ignition. Maintain proper stick-out and keep wire end 2-3mm from workpiece.
- Arc Extinguishing: Keep the torch at the crater briefly to fill it, then slowly raise it to protect the molten pool.
- Weld Bead Connection: Backward welding is generally used.
- Forehand Welding and Backhand Welding: GMAW typically uses forehand welding.
- Electrode Manipulation: Straight moving mode (for sheet metal, backing) or transverse swing mode (for groove filling).
8.3 Welding Operation in Different Positions
8.3.1 Flat Position Welding
Usually uses forehand welding with a traveling angle of 10-15°. Straight moving manipulation for sheet metal and backing, transverse swing for groove filling.
8.3.2 Welding of T-shaped Joints and Lap Joints
Control torch angle carefully to prevent undercut, incomplete penetration, and weld bead sagging. For different plate thicknesses, incline the arc towards the thicker plate for even heating.
8.3.3 Vertical Position Welding
Can be Vertical Position Up or Vertical Position Down. Up welding is rare due to molten metal falling. Parameters are similar to horizontal welding, but current can be slightly higher.
8.3.4 Welding Process Parameters (for information only)
Refer to the tables in the full PDF manual for detailed generalized specification values for standard conditions of gas-shielded welding, including plate thickness, wire diameter, amps, input voltage, welding speed, dry elongation, and gas flow rate for various joint types (I-Shape Butt Welding, Flat Angle T-Shape Butt Weld, Flat Angle Weld Tap).
9. Maintenance (Safeguard)
WARNING: Maintenance should only be performed by qualified professionals with the power supply disconnected to ensure safety.
- Periodic Checks: Regularly check internal circuit connections for tightness. Tighten loose connections. Remove rust or oxidation with sandpaper and retighten.
- Avoid Contact with Energized Parts: Do not allow hands, hair, or tools to contact energized parts (e.g., fan) while the machine is powered on.
- Dust Cleaning: Regularly clean dust with dry compressed air. In dusty environments, clean daily.
- Moisture Protection: Prevent water or vapor from entering the machine. If it does, dry the internal structure and test insulation with a megohmmeter before use.
- Cable Integrity: Periodically check cable insulation. Replace or rewrap any damaged cables.
- Storage: For long-term storage, keep the machine in its original packaging in a dry place.
10. Troubleshooting
Many issues can be resolved by checking common problems before seeking professional help. Always disconnect power before inspection.
| Malfunction | Possible Cause | Solution |
|---|---|---|
| Digital display does not light up, fan does not rotate, no welding output. |
|
|
| Digital display is on, fan rotates normally, but no solder output. |
|
|
| Digital display is on, fan rotates normally, but abnormal indicator light is on. |
|
|
| No response/error code when pressing trigger. |
|
|
| Pressing trigger gets air output and wire feed response, but no output. |
|
|
| Pressing trigger gets gas supply and current output, but no wire feed from torch. |
|
|
| Unstable welding current. |
|
|
11. User Tips
- For aluminum welding, ensure you are using the correct wire and gas settings for optimal results. The HIM250DPP is designed for dual pulse aluminum welding.
- When performing CO2 welding, ensure the gas flow is stable and consistent to achieve clean welds.
- Always double-check all cable connections before starting any welding operation to prevent issues like unstable arcs or no output.
12. Transportation and Storage
12.1 Transportation
Handle the equipment carefully to avoid impact. Protect it from moisture and rain during transportation.
12.2 Storage
- Storage Temperature: -25°C to +50°C
- Storage Humidity: ≤90% relative humidity
- Storage Life: 12 months
- Storage Location: Ventilated indoor area, free from corrosive gases.
13. Warranty and Support
For detailed warranty information and technical support, please refer to the official user manual PDF available at User manual (PDF) or contact HITBOX customer service.
14. Product Video Demonstration
Watch this video for a visual guide on the setup and demonstration of various welding modes of the HITBOX HIM250DPP welding machine.