1. Introduction
The Jikong JK-BD6A24S15P is an advanced Smart Battery Management System (BMS) designed for 8S to 24S battery packs, supporting various battery chemistries including Li-ion, LiFePO4, and LTO. This BMS provides comprehensive protection, active balancing, and real-time monitoring capabilities to ensure the safety, longevity, and optimal performance of your battery system. With built-in Bluetooth, it allows for convenient configuration and monitoring via a dedicated mobile application.

2. Key Features
- Wide Cell Compatibility: Supports 8S to 24S battery configurations.
- High Current Rating: Up to 150A continuous charge/discharge current.
- Active Balancing: Energy transfer balancing to optimize cell voltage uniformity and extend battery life.
- Comprehensive Protection: Includes overcharge, over-discharge, overcurrent, short circuit, and temperature protection.
- Bluetooth Connectivity: Wireless monitoring and parameter adjustment via smartphone app.
- Real-time Monitoring: Displays individual cell voltages, total voltage, current, temperature, State of Charge (SOC), and cycle count.
- Modular Design: Features various interfaces for expansion (RS485, LCD, GPS, CAN, Heating module, NTC module).

3. Setup and Wiring
Proper wiring is critical for the safe and correct operation of the BMS. Please follow these instructions carefully. Incorrect wiring can damage the BMS, battery, or connected equipment.
3.1 Safety Precautions
- Always disconnect the battery pack from any power sources before wiring.
- Wear appropriate personal protective equipment (PPE), including safety glasses and insulated gloves.
- Ensure all connections are secure and properly insulated to prevent short circuits.
- Verify battery polarity before making any connections.
3.2 Wiring Instructions
Due to the complexity of the wiring diagram and the inability to embed it directly, please follow these textual instructions carefully. It is highly recommended to consult the official product page or manufacturer's resources for a visual wiring diagram if available.
- Connect B- Terminal: Connect the thick black wire labeled "B-" from the BMS to the main negative terminal of your battery pack. This is the main negative connection for the entire battery system.
- Connect Balance Wires:
- The balance cable harness consists of multiple thin wires. Identify the thinnest black wire (often labeled B0 or COM). Connect this wire to the main negative terminal of the battery pack (the same point as B-).
- Connect the next wire (B1) to the positive terminal of the first cell group.
- Continue connecting the balance wires sequentially (B2, B3, ..., Bn) to the positive terminals of each subsequent cell group. Ensure the order is correct and matches your battery series configuration (8S to 24S). Each wire should connect to the positive terminal of a cell or cell group.
- Once all balance wires are connected to the battery pack, carefully plug the balance cable harness into the corresponding multi-pin port on the BMS. Ensure it is fully seated and oriented correctly.
- Connect NTC Temperature Sensors: Connect the NTC temperature sensors (if included) to the designated NTC ports on the BMS. These sensors are typically placed on or between battery cells to monitor their temperature for protection.
- Connect P- Terminal: Connect the thick blue wire labeled "P-" from the BMS to the negative terminal of your load (e.g., inverter, motor controller) and charger. This terminal serves as the common negative output for both discharge and charge paths, controlled by the BMS.
- Verify Connections: Before applying power, double-check all connections for correct polarity, secure fitment, and proper insulation. Incorrect wiring can lead to severe damage.

4. Operation and Monitoring (via App)
The Jikong Smart BMS features Bluetooth connectivity, allowing you to monitor and configure your battery system using a dedicated mobile application.
4.1 App Installation and Connection
- Download the App: Scan the QR code on the BMS unit or search for the "Jikong BMS" app in your smartphone's app store (iOS/Android).
- Enable Bluetooth: Ensure Bluetooth is enabled on your smartphone.
- Connect to BMS: Open the Jikong BMS app. The app should automatically detect nearby BMS devices. Select your BMS from the list to connect.
4.2 App Interface Overview
The app provides various screens for monitoring and control. Key sections typically include "STATUS", "SETTINGS", and "CONTROL".

- STATUS Tab: Displays real-time data such as:
- Total Battery Voltage (e.g., 78.48V)
- Current (Charge/Discharge, e.g., 0.0A)
- Battery Power and Capacity
- Cycle Count
- Average Cell Voltage and Delta Cell Voltage
- Individual Cell Voltages (e.g., 3.271V for Cell 1, 3.270V for Cell 2, etc.)
- Balance Current
- MOS Temperature (e.g., 20°C)
- Cells Wire Resistance
- SETTINGS Tab: Allows configuration of various parameters, including:
- Cell Overvoltage Protection (OVPR)
- Power Off Voltage
- Max Charge/Discharge Current
- Overcurrent Protection Delays (OCP Delay, SCPR Time)
- Max Balance Current
- Charge/Discharge Over-Temperature Protection (OTP)
- Charge/Discharge Under-Temperature Protection (UTP)
- MOS Over-Temperature Protection (MOS OTP)
Note: Adjusting settings requires caution. Refer to the specifications and your battery manufacturer's recommendations before making changes.
- CONTROL Tab: Provides options for manual control or system diagnostics (specific functions may vary).
4.3 Active Balancing
The BMS actively balances cells by transferring energy from higher voltage cells to lower voltage cells. This process helps maintain cell voltage uniformity, which is crucial for maximizing battery capacity and extending its overall lifespan.
5. Maintenance
To ensure the long-term reliability and performance of your Jikong Smart BMS and battery pack, consider the following maintenance practices:
- Regular Monitoring: Periodically check the battery status via the mobile app to identify any unusual cell voltage discrepancies, temperature spikes, or protection events.
- Connection Integrity: Ensure all wiring connections, especially the main power and balance wires, remain tight and free from corrosion. Loose connections can lead to poor performance or safety hazards.
- Environmental Conditions: Operate the BMS and battery within their specified temperature ranges. Avoid extreme heat or cold, which can degrade battery performance and lifespan.
- Firmware Updates: Check the app or manufacturer's website for any available firmware updates for the BMS. Updates can improve performance, add features, or fix bugs.
6. Troubleshooting
If you encounter issues with your Jikong Smart BMS, refer to the following common troubleshooting steps:
- BMS Not Powering On/No Output:
- Check the main B- and P- connections for proper polarity and secure contact.
- Verify that the balance wires are correctly connected in sequence and that the harness is fully inserted into the BMS.
- Ensure the battery pack voltage is within the operational range of the BMS (20-100V).
- Bluetooth Connection Issues:
- Ensure Bluetooth is enabled on your smartphone and the app has permission to use Bluetooth.
- Restart the app and try reconnecting.
- Move closer to the BMS to ensure a strong Bluetooth signal.
- If the BMS has been recently powered on, wait a few moments for its Bluetooth module to initialize.
- Cell Voltage Imbalance:
- Allow the BMS to operate for some time; the active balancing feature will work to equalize cell voltages.
- Check individual balance wire connections for looseness or corrosion.
- If a cell is consistently much lower or higher than others, it might indicate a faulty cell in the battery pack.
- Overcurrent/Overvoltage/Undervoltage Protection Triggered:
- Identify the cause of the protection event using the app's status display.
- For overcurrent, reduce the load or charging current.
- For overvoltage/undervoltage, check charger settings or battery health.
- The BMS will typically reset protection after the condition is resolved, or it may require a manual reset via the app or by briefly disconnecting/reconnecting the main power.
7. Specifications
The following tables detail the general and balancing parameters for the JK-BD6A24S15P Smart BMS.
7.1 General Specifications
The following table provides the general technical specifications for the BMS. A visual representation of this table is not available for embedding, but the data is transcribed below.
| Serial Number | Project | Argument | Unit |
|---|---|---|---|
| 1 | Supply voltage | 20-100 | V |
| 2 | Operating power consumption | ≤800 | mW |
| 3 | Operating temperature | -30-70 | °C |
| 4 | Maximum number of collection strings | 24 | String |
| 5 | Maximum balancing current | 0.6 | A |
| 6 | Maximum charging current | 150 | A |
| 7 | Maximum discharge current | 150 | A |
| 8 | Maximum instantaneous current | 300 | A |
| 9 | Maximum internal loop resistance | 0.65 | mΩ |
| 10 | Protective plate size | 162*102*20.4 | mm |
| 11 | Finished weight | 420 | g |
7.2 Balancing Parameters (Configurable via App)
The following table outlines the configurable balancing and protection parameters, with default values for different battery chemistries. A visual representation of this table is not available for embedding, but the data is transcribed below.
| NUM | PARA | LI-ION | LIFEPO4 | LTO | Unit |
|---|---|---|---|---|---|
| 1 | (balancing initial voltage) | 3 | 3 | 2 | V |
| 2 | (Maximum balancing current) | 0.6 | 0.6 | 0.6 | A |
| 3 | (Unit overcharge voltage) | 4.2 | 3.6 | 2.7 | V |
| 4 | (Single overcharge protection recovery) | 4.18 | 3.55 | 2.65 | V |
| 5 | (Monomer undervoltage protection) | 2.82 | 2.6 | 1.8 | V |
| 6 | (Single undervoltage protection recovery) | 2.85 | 2.65 | 1.85 | V |
| 7 | (Automatic shutdown voltage) | 2.8 | 2.5 | 1.7 | V |
| 8 | (SOC-0% voltage) | 2.9 | 2.6 | 1.85 | V |
| 9 | (SOC-100% voltage) | 4.18 | 3.5 | 2.65 | V |
| 10 | (Trigger balancing differential pressure) | 0.01 | 0.01 | 0.01 | V |
| 11 | (Charging overcurrent protection delay) | 30 | 30 | 30 | seconds |
| 12 | (Charge overcurrent protection release time) | 60 | 60 | 60 | seconds |
8. User Tips
- Initial Balance: For new battery packs, allow the BMS to perform initial balancing for several charge/discharge cycles to achieve optimal cell voltage uniformity.
- App Permissions: Ensure the Jikong BMS app has all necessary permissions (e.g., Bluetooth, location) on your smartphone for seamless operation.
- Firmware Updates: Regularly check for and install firmware updates for the BMS via the app or manufacturer's instructions to benefit from improvements and new features.
- Heat Management: While the BMS has temperature protection, ensure adequate ventilation around the battery pack and BMS, especially during high current operation, to prevent overheating.
9. Warranty and Support
For technical support, warranty claims, or any questions regarding the operation and maintenance of your Jikong JK-BD6A24S15P Smart BMS, please contact the manufacturer or your point of purchase. Keep your purchase records handy when seeking support.
For detailed information on the internal architecture and module interactions, refer to the block diagram below. A visual representation of this diagram is not available for embedding, but the key components are listed:

- MCU (Microcontroller Unit): The central processing unit of the BMS.
- Current Acquisition: Module for measuring charge and discharge currents.
- EEPROM: Non-volatile memory for storing settings and data.
- LED Indication: Visual indicators for status.
- Buzzer: Audible alerts for warnings or errors.
- Bluetooth Module: Enables wireless communication with the mobile app.
- Acquisition Module: For data collection from cells.
- Gated Module: Controls power flow.
- Active Balancing Module: Manages cell voltage equalization.
- Power Module: Provides power to internal components.
- NTC Module: For temperature sensing.
- Interfaces: RS485, LCD, GPS, CAN for external communication and display.
- MOS Driver Circuit: Controls the MOSFETs for charge/discharge paths.
- Sampling Resistor: Used for current measurement.