Victgoal Visor for VG110, VG112, VA110, VA112 Helmets

Contents

VICTGOAL Bike Helmet Sun Visor User Manual

Model: Visor for VG110, VG112, VA110, VA112 Helmets

Brand: Victgoal

Introduction

This manual provides comprehensive instructions for the proper installation, removal, and maintenance of your VICTGOAL Bike Helmet Sun Visor. Designed for compatibility with VICTGOAL helmet models VG110, VG112, VA110, and VA112, this visor enhances your riding experience by providing sun protection. Please read these instructions carefully before use to ensure correct handling and to prevent damage to the product or your helmet.

Safety Information

  • Always ensure the visor is securely attached before riding.
  • Do not attempt to modify the visor or helmet in any way.
  • Improper installation or removal can damage the visor or helmet.
  • This product is a sun visor accessory and does not provide additional impact protection beyond what the helmet offers.

Specifications

FeatureDetail
MaterialPVC
CompatibilityVICTGOAL Helmet Models: VG110, VG112, VA110, VA112
Package Weight0.12 kg
Package Dimensions17 x 10 x 7 cm

Installation and Removal

The VICTGOAL sun visor is designed for easy attachment and detachment. Refer to the diagram below (from the official PDF manual) and the video for a visual guide.

Diagram Reference (from PDF manual):

  • The visor has three attachment points: a middle pin (labeled '1') and two side pins (labeled '2' and '3').
  • The visor also has two side sections, 'A' and 'B', which are important for proper removal.

Installation Steps:

  1. Align the middle pin (1) of the visor with the corresponding hole on the helmet.
  2. Gently push the middle pin into place.
  3. Align the side pins (2 and 3) of the visor with the side holes on the helmet.
  4. Press firmly on the sides of the visor until the side pins click securely into their respective holes.

Removal Steps:

  1. Start by gently disengaging the side pins (3 and 2) from the helmet.
  2. Once the side pins are free, carefully hold the A and B sides of the visor and pull the middle pin (1) out simultaneously.

Warning for Removal:

When removing the middle pin (No. 1 hole), you must hold the A and B sides of the visor and pull out at the same time. Incorrect installation and removal may cause damage to the sun visor.

Visual Aid:

Visor attached to a black helmet, showing compatibility with VG110/VG112 models.

Image: VICTGOAL Sun Visor installed on a compatible helmet (VG110/VG112).

Visor attached to a black helmet, showing compatibility with VG122/VG123 models.

Image: VICTGOAL Sun Visor installed on a compatible helmet (VG122/VG123).

Close-up of the visor's attachment pin.

Image: Close-up of a visor attachment pin.

Instructional Video:

Video: Demonstrates the step-by-step process for both installing and removing the sun visor from a helmet.

Usage

Once installed, the VICTGOAL Bike Helmet Sun Visor provides shade and reduces glare during your rides. It is designed to remain in a fixed position to offer consistent protection. Ensure the visor is firmly attached before each use.

Maintenance

  • Clean the visor with a soft, damp cloth and mild soap. Avoid abrasive cleaners or solvents that could damage the PVC material.
  • Rinse thoroughly with clean water and dry with a soft, lint-free cloth.
  • Store the visor in a cool, dry place away from direct sunlight when not in use to prevent material degradation.
  • Regularly inspect the attachment points for any signs of wear or damage.

Troubleshooting

Visor difficult to install or remove:

  • Ensure correct alignment of the pins with the helmet holes.
  • For removal, refer to the "Removal Steps" and the warning regarding holding the middle part.
  • Do not force the visor, as this may damage the pins or the helmet.

Visor feels loose after installation:

  • Verify that all three pins (middle and two sides) are fully engaged and clicked into place.
  • Check for any obstructions in the helmet's attachment holes.

User Tips

  • When removing the visor, especially the middle pin, it is crucial to hold both sides (A and B as indicated in the PDF diagram) of the visor firmly and pull it out simultaneously. This technique helps prevent stress on the pins and reduces the risk of breakage, as noted by users.
  • Always double-check the compatibility of the visor with your specific helmet model (VG110, VG112, VA110, VA112) before attempting installation.

Warranty and Support

For any questions regarding your VICTGOAL Bike Helmet Sun Visor, please refer to the official user manual PDF or contact Victgoal customer support. The PDF manual contains detailed diagrams and additional information.

Official User Manual (PDF): Download PDF

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.