WINXU FOC Sine Wave Controller S866 LCD Display Set

Contents

WINXU 36V/48V 350W 18A FOC Sine Wave Brushless Motor Controller & S866 LCD Display Set User Manual

Model: FOC Sine Wave Controller S866 LCD Display Set

1. Product Overview

This manual provides detailed instructions for the installation, operation, and maintenance of your WINXU 36V/48V 350W 18A FOC Sine Wave Brushless Motor Controller and S866 LCD Display Set. This system is designed for electric scooters and bicycles, offering efficient and stable control for brushless motors.

The controller features a sinusoidal drive design for stable waveform output and low noise operation, with an 18A current capacity. Its self-learning function ensures high compatibility with most brushless motors. The S866 LCD display provides essential ride data and allows for parameter adjustments.

WINXU FOC Sine Wave Brushless Motor Controller and S866 LCD Display Set
Figure 1: WINXU FOC Sine Wave Brushless Motor Controller and S866 LCD Display Set.

2. Important Notes and Warnings

  • Compatibility: This controller is exclusively designed for brushless motors with Hall sensors. It is not suitable for brush motors. Using it with a Hall-less brushless motor will result in a persistent E07 fault code.
  • Initial Setup: After initial installation, it is crucial to perform the self-learning procedure by plugging in the learning wires to properly configure motor parameters.
  • PAS Sensor: If utilizing pedal assist (PAS) functionality, a dual Hall PAS sensor is required for proper operation.
  • Cruise Mode: The software for this sine wave controller does not include a cruise mode function.
  • E07 Fault Code: If your motor is Hall-less or its Hall sensor is damaged, the E07 fault code will always be displayed. Please consider this before purchase if this is unacceptable.

3. Product Features

  • FOC Sine Wave Control: Provides smooth, quiet, and efficient motor operation.
  • Wide Voltage Compatibility: Supports both 36V and 48V battery systems.
  • High Power Output: Rated for 350W motors with an 18A current limit.
  • Self-Learning Function: Automatically detects and adapts to motor parameters for broad compatibility.
  • Durable Construction: Controller features IPX6 waterproof design and pure aluminum alloy material for stable heat dissipation.
  • Quality Components: High-quality lead-free PCB process and fire-resistant wire materials ensure reliability.
Controller details showing IPX6 waterproof design and aluminum alloy material
Figure 2: Controller construction details, highlighting IPX6 waterproof design and aluminum alloy casing for heat dissipation.
Internal view of controller PCB and wiring
Figure 3: Internal view of the controller, showcasing the high-quality lead-free PCB and fire-resistant wiring.

4. Specifications

AttributeValue
TypeController
Input Voltage36V / 48V
Motor Power350W
Current Limit18A
Motor TypeBrushless motor (requires Hall sensor)
LCD ModelS866
Protocol TypeUART
Controller Dimensions (L x W x H)Approx. 100mm x 70mm x 32.5mm (3.93in x 2.75in x 1.28in)
LCD Display Dimensions (L x W)Approx. 82mm x 52mm
OriginMainland China
Controller dimensions: 100mm length, 70mm width, 32.5mm height
Figure 4: Dimensions of the FOC Sine Wave Brushless Controller.
S866 LCD Display dimensions: 82mm length, 52mm height
Figure 5: Dimensions of the S866 LCD Display.

5. Setup and Installation

5.1 Wiring Diagram

Carefully follow the wiring diagram below to connect the controller to your e-scooter or e-bike components. Ensure all connections are secure and correctly matched.

FOC Sine Wave Brushless Controller Wiring Diagram showing connections for Battery, Throttle, Power lock, LCD/LED Display (5p), PAS Sensor, Low level brake, Self-learning, Light power supply, Hall Sensor, Motor U.V.W (3-phase wire)
Figure 6: FOC Sine Wave Brushless Controller Wiring Diagram. Connectors are labeled for Battery, Throttle, Power lock, LCD/LED Display (5p), PAS Sensor, Low level brake, Self-learning, Light power supply, Hall Sensor, and Motor U.V.W (3-phase wire).

5.2 S866 LCD Display Wiring

The S866 LCD display connects to the controller via an SM-5P connector. If connecting a headlight, use the SM-2P connector as shown below. Note that the headlight is not included.

S866 LCD Display Wiring Diagram showing SM-5P connector for controller (Red: VCC, Black: GND, Green: RX, Yellow: TX) and SM-2P connector for headlight (White: GND, Brown: VCC)
Figure 7: S866 LCD Display Wiring Diagram. Details SM-5P connector for controller (Red: VCC, Black: GND, Green: RX, Yellow: TX) and SM-2P connector for headlight (White: GND, Brown: VCC).

5.3 Initial Motor Self-Learning

Upon the first installation, the motor may exhibit jitter. This is normal as the controller needs to learn your motor's specific parameters. To perform the self-learning function:

  1. Ensure all other connections are made correctly.
  2. Locate the self-learning wires on the controller (refer to Figure 6).
  3. Short-circuit the self-learning wires for approximately 5 seconds. The controller will automatically detect and configure your motor parameters.

5.4 Adjusting Motor Direction

If, after initial installation and self-learning, your motor drives in the reverse direction, this can be easily corrected:

  • Simply short-circuit the self-learning wires again. This action will toggle the motor's direction.

6. Operating Instructions

6.1 S866 LCD Display Overview

The S866 LCD display provides real-time information and control over your e-bike/scooter. Familiarize yourself with the buttons and display areas:

S866 LCD Display button functions and display areas: + button, On-off button, - button, Real-time speed display area, PAS gear display area, Battery capacity display, Mileage/Voltage/Error Code Display Area, Mileage/Voltage/Total Mileage Icon Display
Figure 8: S866 LCD Display layout and button functions.
  • '+' Button: Short press to change gear; long press to control headlight.
  • On-off Button: Long press to switch on/off; short press to switch mileage display.
  • '-' Button: Short press to change gear; long press to enter cruise mode (Note: This controller software does not support cruise mode, so this function will not be active).

6.2 Entering Setup Mode

To access the display's parameter settings:

  1. Switch on the display.
  2. Long press both the '+' and '-' buttons simultaneously for 3-5 seconds.
  3. The parameters on the screen will begin to blink, indicating you are in setup mode.

While in setup mode:

  • Short press the 'M' button to cycle through different parameters.
  • Use the '+' and '-' buttons to adjust the selected parameter's value.

6.3 Parameter Introduction (P-Codes)

The following parameters can be adjusted in setup mode:

  • P00: Restore factory settings.
  • P01: Backlight Brightness.
  • P02: Mileage unit (e.g., km/h or mph).
  • P03: Voltage selection (e.g., 36V, 48V).
  • P04: Sleep Time (auto-off duration).
  • P05: PAS Gear (number of pedal assist levels).
  • P06: Wheel Diameter (in inches, for accurate speed calculation).
  • P07: Speed Magnet (number of magnets in the motor for speed sensing).
  • P08: Speed Limit.
  • P09: Zero Start / Non-Zero Start (whether motor assists from standstill or after initial pedal).
  • P10: Drive mode setting:
    • 0: PAS drive only
    • 1: Throttle drive only
    • 2: PAS and throttle drive
  • P11: PAS sensitivity setting.
  • P12: PAS start strength setting.
  • P13: PAS magnet disc type setting.
  • P14: Current Limit Setting.
  • P15-P19: Functions not yet opened; ignore these settings.

6.4 Error Code Explanation

The S866 LCD display will show decimal fault codes to indicate system issues:

  • E00: Normal status.
  • E01: (No specific description provided, typically a general error).
  • E02: Brake fault.
  • E03: PAS sensor fault.
  • E04: 6KM/H cruise mode (indicates cruise mode is active, not an error).
  • E05: Real-time cruise (indicates real-time cruise is active, not an error).
  • E06: Battery undervoltage.
  • E07: Motor failure (specifically for Hall-less motors or damaged Hall sensors).
  • E08: Throttle fault.
  • E09: Controller failure.
  • E10: Communication signal reception failure.
  • E11: Communication signal transmission fault.
  • E12: BMS communication fault.
  • E13: Headlight fault.

6.5 Speed Display Calibration

To ensure accurate speed readings on your LCD display:

  1. Enter LCD setting mode (Section 6.2).
  2. Adjust P06 (Wheel Diameter) to match your motor wheel's diameter in inches.
  3. Adjust P07 (Speed Magnet). A common starting value is 23.
  4. Test the real-time speed using a map navigation app on your smartphone.
  5. If the LCD speed is higher than the navigation app, decrease the P07 parameter.
  6. If the LCD speed is lower than the navigation app, increase the P07 parameter.
  7. Repeat steps 4-6 until the LCD displays an accurate speed.

7. Maintenance

To ensure the longevity and optimal performance of your controller and display set, consider the following general maintenance tips:

  • Regular Cleaning: Keep the controller and display free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning.
  • Inspect Wiring: Periodically check all wiring connections for signs of wear, corrosion, or looseness. Secure any loose connections.
  • Water Exposure: While the controller has an IPX6 waterproof design, avoid submerging it in water or exposing it to high-pressure water jets. Ensure the rubber seals around cable entries are intact.
  • Storage: When not in use for extended periods, store the e-bike/scooter in a dry, temperate environment.

8. Troubleshooting

This section addresses common issues and their potential solutions. Refer to Section 6.4 for a complete list of error codes.

  • Motor Jittering / Incorrect Direction on First Use:

    Cause: The controller has not yet learned the motor parameters or the motor direction is incorrect.

    Solution: Perform the self-learning procedure (Section 5.3) by short-circuiting the self-learning wires for 5 seconds. If the direction is still incorrect, short-circuit them again to reverse the direction.

  • E07 Error Code Displayed:

    Cause: This error indicates a motor failure, specifically that the motor is Hall-less or its Hall sensor is damaged. This controller requires a Hall sensor motor.

    Solution: Verify your motor has a functional Hall sensor. If your motor is Hall-less, this controller is incompatible, and the E07 code will persist.

  • Inaccurate Speed Display:

    Cause: Incorrect wheel diameter (P06) or speed magnet (P07) settings.

    Solution: Calibrate the speed display by adjusting P06 and P07 parameters in the LCD setup mode (Section 6.5).

  • No Power to Display / System Not Turning On:

    Cause: Loose battery connection, power lock issue, or controller failure (E09).

    Solution: Check battery connections, ensure the power lock is engaged, and inspect controller wiring. If E09 is displayed, the controller may require replacement.

  • PAS Not Working (E03 Error):

    Cause: PAS sensor fault or incorrect PAS sensor type.

    Solution: Ensure a dual Hall PAS sensor is installed and correctly wired. Check the sensor for damage. Adjust PAS sensitivity (P11) and start strength (P12) if needed.

9. User Tips

Based on common user experiences, here are some tips for optimizing your experience with the WINXU FOC Sine Wave Controller and S866 LCD Display Set:

  • Double-Check Wiring: Before powering on for the first time, meticulously review all wiring connections against the provided diagram. Incorrect wiring is a common cause of initial issues.
  • Patience with Self-Learning: The self-learning process is crucial. Allow the controller sufficient time (approx. 5 seconds) to complete its motor parameter detection.
  • Speed Calibration: Take the time to accurately calibrate your speed display using a GPS-enabled app. This ensures reliable speed and mileage readings.
  • Understand Error Codes: Familiarize yourself with the error codes (Section 6.4) to quickly diagnose and address potential problems.

10. Support and Contact

For further assistance, technical support, or inquiries regarding your WINXU FOC Sine Wave Brushless Motor Controller and S866 LCD Display Set, please contact your retailer or the manufacturer directly.

When contacting support, please be prepared to provide:

  • Your product model and any relevant serial numbers.
  • A detailed description of the issue you are experiencing.
  • Any error codes displayed on the S866 LCD.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.