ETENWOLF ZEPHYR S3

Contents

ETENWOLF ZEPHYR S3/S3 Plus Portable Tire Inflator User Manual

Model: ZEPHYR S3 / S3 Plus

Introduction

Thank you for choosing the ETENWOLF Zephyr S3/S3 Plus Air Compressor. Designed to inflate a wide range of tires and inflatables, this portable power station pump enhances versatility for your outdoor adventures.

Safety Warning: Please read all safety warnings and all instructions to reduce the risk of electric shock, fire and/or serious injury.

Product Overview

Familiarize yourself with the components and display of your Zephyr S3/S3 Plus Air Compressor.

Diagram showing the front and side views of the ETENWOLF Zephyr S3/S3 Plus Air Compressor with numbered parts and controls.
Figure 1: Product Overview - Front and Side Views

Controls and Display Elements:

  1. Unit button
  2. Light button
  3. "-" decrease pressure button
  4. Mode button
  5. Start/pause power button
  6. "+" increase pressure button
  7. Center display
  8. LED work light
  9. Pressure hose
  10. Type-C port (Input)
  11. USB-A port (Output)
  12. Presta valve adapter
  13. Inflation needle
  14. High-pressure tapered nozzle
  15. Manual mode
  16. Car mode
  17. Bicycle mode
  18. Ball mode
  19. Pressure unit
  20. Target input value
  21. Actual pressure value
  22. Battery level indicator
  23. Safety alert symbol

Setup

Package Content

Ensure all items are present in your package:

Diagram showing all components included in the ETENWOLF Zephyr S3/S3 Plus Air Compressor package.
Figure 2: Package Contents
  • 1x Zephyr S3/S3 Plus Air Compressor
  • 1x Air Chuck
  • 1x Pressure hose
  • 1x Presta valve adapter
  • 1x Inflation needle
  • 1x High-pressure tapered nozzle
  • 1x USB A to C cable
  • 1x User manual

Operating Instructions

Quick Start Guide - Steps to Inflate

Diagram illustrating the steps to inflate an item using the ETENWOLF Zephyr S3/S3 Plus Air Compressor.
Figure 3: Inflation Steps
  1. Remove the Pressure hose (9) from its storage channel.
  2. Insert the nozzle (9) clockwise into the object being inflated.
  3. Press the Start/pause power button (5) to activate the machine.
  4. Press Mode button (4) to switch among 4 different modes: Manual mode (15), Car mode (16), Bicycle mode (17), Ball mode (18).
  5. Select the pressure unit between PSI, KPa, and Bar by pressing the Unit button (1).
  6. Press "-" button (3) to decrease or "+" button (6) to increase the target pressure value.
  7. Press Start/pause power button (5) again to start inflation.
  8. When the inflated item reaches the preset value, the unit will turn off automatically.

Note:

  • To stop inflation at any time, press the Start/pause power button (5).
  • The ETENWOLF system will automatically remember the previous pressure settings when the unit is used again.
  • Double check the target input value. Setting a wrong value might lead to an inflated item explosion.
  • After the tire is inflated, the temperature inside the tire will decrease to the ambient temperature, causing the tire pressure to decrease by 0.5 to 1.5 PSI.
  • When finishing pumping a bike tire, don't forget to quickly remove the hose. Otherwise, the losing air may lessen the tire pressure.

Steps to Check Pressure

  1. Connect the pressure hose (9) to the item.
  2. Press the Start/pause power button (5) to power on.
  3. The head display (7) will display the current pressure.

Button Operation Guide

Start/pause Power Button (5)

  • ON: Long-press Start/pause power button (5) for two seconds to turn on.
  • OFF: When the inflator is turned on, long-press Start/pause power button (5) for two seconds to turn off.

Automatic Shut-off Conditions

The inflator will automatically turn off in the cases below:

  1. 3 minutes of inactivity.
  2. When the charging cable is accidentally disconnected during charging.
  3. 5 minutes of inactivity after being fully charged.
  4. 5 minutes inactivity after being used as a power bank.
  5. When inflating over 5 minutes, but the actual pressure is still below 5 PSI.
  6. When inflating over 5 minutes, but the actual pressure is above 150 PSI.

Preset Pressure Value

The number with the smaller size on the top of the display indicates the target input (20), and the number with the bigger size on the button of the display indicates the actual value (21) of the inflated devices.

ModeAdjustable Pressure RangeDefault Pressure
Car mode8-130 PSI35 PSI
Bicycle mode10-145 PSI22 PSI
Ball mode3-16 PSI8.5 PSI
Manual mode3-160 PSI30 PSI

LED Work Light

An LED work light (8) is in the front of the inflator. To turn the light on, first power on the machine by pressing the Start/pause power button (5) and then press LIGHT button (2).

Switch between four different light modes:

  • Bright flashlight
  • Ultra-bright flashlight
  • Slow strobe light: light turns on and off.
  • SOS signal: 3 short strobe signals, followed by 3 long strobe signals, and then 3 more short strobe signals, repeated in a loop.

Note:

  • The light will automatically turn off after 1 hour. After the first automatic turn off, you can manually turn on the LED light for the second time. Once manually turned on for the second time, it will not automatically turn off; it must be manually turned off.

Power Bank Function

The inflator can also function as a power bank to charge your electronic devices such as phones, tablets, laptops, drones, and cameras. It has a USB-A Output 5V 2A, 10W.

Diagram showing the ETENWOLF Zephyr S3/S3 Plus Air Compressor charging a mobile phone.
Figure 4: Power Bank Functionality

Note:

  • To work as a power bank, the inflator needs to be powered on.
  • After 3 minutes of charging, the display panel will only indicate the battery level to save battery.
  • After 2 minutes of fully charging the devices, the inflator will automatically turn off.

Maintenance

Battery Charging & Indicator

For optimal charging performance and stability, use a 5V 3A 15W PD charger to fuel the built-in battery. Battery charging takes approximately 3.5 hours to fully charge from 0% to 100%. Using a 5V 2A 10W charger takes approximately 6 hours to fully charge from 0% to 100%.

Diagram showing the ETENWOLF Zephyr S3/S3 Plus Air Compressor connected to a charger.
Figure 5: Battery Charging

Charging Procedure:

Fully charge the inflator before using it for the first time. Connect it to a certified 5V 3A/5V 2A charger with the charging cable.

Battery Level Indicator:

The battery level indicator (22) is shown by four bars, with each bar representing 25% of capacity.

While Charging Indicators:

  • 0% - 5% charged
  • 5% - 25% charged
  • 25% - 50% charged
  • 50% - 75% charged
  • 75% - 100% charged
  • Fully charged

Note:

  • After 2 minutes of inactivity after being fully charged, the inflator will automatically shut off.
  • The inflator cannot be used while it is charging.

Pressure Recalibration

Different altitudes can cause variations in pressure by 1-3 PSI. In high-altitude areas (especially over 5000 ft/1524 meters), users can recalibrate the pump's pressure sensor.

Recalibration Steps:

  1. Power on (5) the pump.
  2. Hold the Light button (2) and Mode button (4) for 10 seconds.
  3. When the entire screen flickers, it indicates recalibration is complete.

Note:

  • Power off the pump before calibration.
  • The Pressure hose (9) should not be connected to any item. Any item which gives pressure to the hose will disable the process of recalibration.
  • A charged battery or other power source is required to process recalibration.
  • There is no memory for the new recalibration settings. Once the power is turned off, it will be reset to sea level calibration (altitude 0 ft/meters).

Troubleshooting

ProblemSolution
Slow inflation speed
  • Check whether the battery is sufficient.
  • Check whether the item inflated is leaking.
  • Check whether the air nozzle connection is tightened.
  • Check whether the inflation hoses are broken.
  • Check whether the ventilation slots are blocked.
Air compressor turns on, but does not inflate
  • Check whether the battery is sufficient.
  • Check whether the pressure of the item being inflated exceeds the preset pressure.
Unable to increase or decrease the preset pressure
  • Make sure the correct mode is chosen, and the preset value does not exceed the range.
  • Select the manual mode and adjust the preset value within the pressure range of 3-160 PSI.
The inflator inflates but the pressure shown on the display is zero.If the air pressure is under 3 PSI, the pressure displayed will show zero due to the pump's minimum pressure range.
The battery level indicator is different when inflating compared to the standby state.The lithium battery's voltage level significantly drops when discharging power, causing the battery level indicator to have a different display when inflating compared to a standby state. It is a normal situation.
The battery level indicator does not show on the screen after charging.Use a certified ETENWOLF charger or standard charger, and the included charging cable, and try to charge it.
There is an air leakage when connecting the high-pressure air hose.Tighten the air nozzle.
Safety alert symbol light on display shows the E08 error code.After shutting down and restarting, if the issue persists, it is necessary to send the device for factory repair.
Display shows the E10 error code.This is a motor malfunction warning, with the motor ceasing to function. After flashing for 30 seconds, it should return to normal. If the issue persists after shutting down and restarting, it is recommended to send the device for factory repair.
Display shows the E11 error code.The low-temperature charging protection icon indicates that the temperature during charging is too low. It is necessary to restore the temperature to above 0 degrees Celsius before continuing with the charging process.
Display shows the E12 error code.The high-temperature charging protection icon indicates that the temperature during charging is too high. It is necessary to restore the temperature to below 45 degrees Celsius before continuing with the charging process.
Display shows the E13 error code.The low-temperature discharge protection icon indicates that the temperature is too low during inflation or charging other devices. It is necessary to restore the temperature to above -20 degrees Celsius before continuing with the process.
Display shows the E14 error code.The high-temperature discharge protection icon indicates that the temperature is too high during inflation or charging other devices. It is necessary to restore the temperature to below 58 degrees Celsius before continuing with the charging process.
Display shows the E15 error code.The air pump has exceeded the working time, and the warning icon flashes for 30 seconds before returning to normal. Check if the inflated item has any leakage.
Display shows the E16 error code.The overpressure protection icon will return to normal after pressure release.
Display shows the E17 error code.The high-pressure operation has exceeded the working time, and the warning icon flashes for 30 seconds before returning to normal. Check if the inflated item is functioning abnormally.
Display shows the E18 error code.The battery damage warning icon and the battery level indicator icon. After 30 seconds flashing, the device will shut down. It is necessary to send the device for factory repair.

Specifications

NameAir Inflator
ModelZephyr S3/S3 Plus Air Compressor
Dimensions134 x 171 x 96mm (6.7 x 5.3 x 3.5 inches)
Inflation pressure range3-160 PSI / 0.2-11 Bar
Operating TemperatureCharging: 0°C-45°C / 30°F-113°F
Discharging: -20°C-70°C / -4°F-158°F
Storage temperature-10°C-60°C / -14°F-140°F
High pressure air tube length0.9 meters
Battery capacity7800mAh for S3 / 9600mAh for S3 Plus
Working noiseLower than 85dB within 1 meter
InputType-C: 5V 3A
OutputUSB-A: 5V 2A
Charging time15W 3.5 hours / 10W 6 hours
Continuous working timeApproximately 25 minutes at a pressure range of 20-50 PSI, in a 25°C ambient temperature, under full charge
Sensor accuracy±1 PSI

Safety Instructions

  1. This product is not a toy and should not be used by children. Users should be above 16 years old. Keep a safe distance between children and the inflator while inflating. There is a built-in lithium battery inside the product. Don't place the product into fire or dump the battery.
  2. Overheating damage or water ingress may increase the risk of fire or explosion. It's best to keep the product away from heat sources, and not leave it for prolonged periods in a hot car. If the inflator becomes very hot, there is a chance it could explode.
  3. Please store the product within temperatures ranging from -10°C-60°C / -14°F-140°F. Extremely hot or cold environments may damage the battery and shorten the lifetime of the inflator. Long-time storage of the product may decrease the effectiveness of the battery.
  4. Charge the inflator at least once every three months to maintain its performance.
  5. The product has a built-in DC motor which may generate sparks during operation. Do not use it in an environment with dust or gas that is liable to explode.
  6. If there is an unusual noise or the temperature becomes very high during inflating, please turn off the inflator immediately.
  7. Before setting the inflation pressure value, make sure the pressure unit is correctly selected. Mixing up PSI and Bar could lead to dangerous overinflation.
  8. Unit conversion: 1 Bar = 14.5 PSI. 1 Bar = 100 KPa.
  9. Do not leave the pump unattended while it is in operation.
  10. Please use the product in a dry and clean environment. The intrusion of sand and dust may cause damage to the product. Don't wash the product with water.
  11. Make sure to use ETENWOLF's charger or other certified PD chargers, and the included charging cable to charge this product. Malfunction caused by actions not in accordance with the above requirements is not covered by the warranty.
  12. To reduce the risk of electric shock, do not expose to rain. Store indoors.

User Tips

  • No Deflation Function: This device is designed for inflation only and does not have a deflation capability.
  • Charging Usage: The inflator cannot be used while it is charging. Ensure it is fully charged before use.
  • Noise Level: The operating noise level is typically lower than 85dB within 1 meter.
  • Check for S3 vs S3C: Be aware that there might be different versions (e.g., S3 and S3C). Always refer to your specific model's manual for precise details.

Warranty & Support

2-Years Coverage

Within two years of purchase, we will provide timely and effective online after-sale service. We will repair or replace any defective product (due to manufacturing fault) within this warranty period.

Contact Information:

Made in P.R.C.

For the full user manual in PDF format, please refer to the official document: ETENWOLF Zephyr S3/S3 Plus Air Compressor User Manual (PDF)

Product Video

Watch the official product video for a visual guide on the ETENWOLF Zephyr S3/S3 Plus Portable Tire Inflator.

Official product demonstration video for the ETENWOLF Zephyr S3/S3 Plus Air Compressor.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.