Introduction
The SKMEI 2063 is a versatile digital sports watch designed for durability and functionality. Featuring a clear LED display, shock resistance, and 50-meter water resistance, it is suitable for various activities. This manual provides essential information on setting up, operating, and maintaining your watch to ensure optimal performance and longevity.
Setup
Your SKMEI 2063 watch comes with a battery included. Before initial use, ensure all protective films are removed from the display and case. The watch features five buttons for operation: Back Light, Mode, Reset, Start, and Alarm.
Button Functions:
- Back Light Button (Top Left): Activates the EL backlight for visibility in low-light conditions.
- Mode Button (Bottom Left): Cycles through different modes: Time, Chronograph (Stopwatch), Alarm, and Countdown.
- Reset Button (Center Left): Used to reset the chronograph, adjust settings during time/alarm setup, or switch between 12/24-hour format.
- Start Button (Top Right): Starts/stops the chronograph, increments values during time/alarm setting.
- Alarm Button (Bottom Right): Toggles the alarm on/off and enters alarm setting mode.
Initial Time Setting:
- Press the Mode Button repeatedly until you reach the Time Setting mode (usually indicated by flashing digits).
- Use the Reset Button to select the digit you wish to adjust (e.g., hours, minutes, year, month, day).
- Use the Start Button to increment the selected digit.
- Once all settings are correct, press the Mode Button again to exit the setting mode.
Operating Instructions
Time Display:
The watch displays time in either 12-hour (with AM/PM indicator) or 24-hour format. You can switch between these formats during time setting using the Reset button.
Chronograph (Stopwatch):
- Press the Mode Button until the chronograph mode is displayed (often indicated by '00:00:00' and '1/100 SEC').
- Press the Start Button to begin timing.
- Press the Start Button again to pause timing.
- Press the Reset Button to clear the stopwatch to zero.
Alarm:
- Press the Mode Button until the Alarm mode is displayed.
- Press the Reset Button to select the hour or minute digits.
- Use the Start Button to set the desired alarm time.
- Press the Alarm Button to toggle the alarm on or off (an alarm icon will appear/disappear on the display).
EL Light (Backlight):
Press the Back Light Button (top left) to illuminate the display for a few seconds.
Date and Week Display:
The watch automatically displays the current date and day of the week once set correctly in time setting mode.
Multiple Time Zone:
The watch supports a second time zone function. Access this mode via the Mode Button and set it similarly to the main time.
Countdown Timer:
The countdown timer can be set for a specific duration. Access this mode via the Mode Button and use the Reset and Start buttons to set and operate the timer.
Maintenance
Proper care will extend the life and appearance of your SKMEI 2063 watch.
Water Resistance:
The watch is rated for 50 meters (5ATM) water resistance. This means it is suitable for daily use, swimming, and showering with cold water only. It is important to note that the watch cannot be used with hot water or warm water for bathing and showering, as water vapor can enter and damage the internal components.
Chemical Exposure:
Avoid exposing the watch to chemical-containing cosmetics, solvents, or corrosive daily necessities. These substances can corrode the plating and finish of the watch surface.
Cleaning:
Clean the watch regularly with a soft, dry cloth. For stubborn dirt, a slightly damp cloth can be used, followed by immediate drying.
Storage:
When not in use, store your watch in a cool, dry place away from direct sunlight and extreme temperatures.
Troubleshooting
- Display is blank or dim: The battery may be low or depleted. Replace the battery.
- Buttons are unresponsive: Ensure the watch is not in a locked mode (if applicable, though not specified for this model). If issues persist, a soft reset (removing and reinserting the battery) might be necessary, or contact support.
- Time is incorrect: Re-adjust the time following the 'Initial Time Setting' instructions. Ensure the 12/24-hour format is set as desired.
- Water inside the watch: If moisture appears inside the watch, stop using it immediately and seek professional service. This usually indicates a breach in water resistance.
Specifications
| Feature | Specification |
|---|---|
| Brand | SKMEI |
| Model Number | 2063 |
| Movement | Digital |
| Display Type | Digital (LED Display) |
| Case Material | Plastic (PC) |
| Dial Window Material Type | Resin |
| Band Material Type | Silicone (Silica Gel) |
| Clasp Type | Buckle (Stainless Steel) |
| Water Resistance Depth | 5Bar (50 meters) |
| Features | Shock Resistant, LED Display, Repeater, Chronograph, Complete Calendar, Multiple Time Zone, Alarm, Week Display, Countdown |
| Case Shape | Round |
| Dial Diameter | 44.3mm |
| Case Thickness | 13.5mm |
| Band Width | 20mm |
| Band Length | 24.5cm |
| Weight | 47.4g |
| Battery Included | Yes |
| Certification | CE |
User Tips
- Time Adjustment: If you find it challenging to adjust the time, refer to the 'Initial Time Setting' section carefully, paying attention to which button increments and which selects the digit. Practice cycling through modes to familiarize yourself with the watch's interface.
- Water Resistance: Always remember that 50M water resistance is for cold water only. Avoid hot showers, saunas, or steam rooms to prevent internal damage.
Warranty and Support
For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase. Specific warranty terms and conditions may vary by region and seller.
