1. Introduction
This manual provides essential information for the safe and effective operation of your EAFC 12V 8A Smart Pulse Repair Car Battery Charger. This intelligent charger is designed to automatically charge and maintain various 12V batteries, including lead-acid (calcium, gel, AGM, wet, EFB) and LiFePO4 types, with an emphasis on pulse repair functionality to restore battery performance and extend life.
The EAFC 12V 8A Smart Pulse Repair Car Battery Charger.
2. Important Safety Instructions
WARNING: Read all safety warnings and instructions before using this product. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.
- California Proposition 65 Warning: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- Always connect the charger to the battery terminals correctly: red clamp to the positive (+) terminal and black clamp to the negative (-) terminal.
- Ensure the charger is used indoors and protected from rain and moisture.
- This charger is designed for battery capacities between 2Ah and 150Ah. Verify your battery's capacity before use.
- It is strictly forbidden to charge LiFePO4 batteries without a Battery Management System (BMS).
- Do not carry the charger with the vehicle to prevent shock or damage.
- Avoid short-circuiting the output terminals.
- Do not disassemble the charger. Refer all servicing to qualified personnel.
- Keep out of reach of children.
3. Package Contents
Your EAFC 12V 8A Smart Pulse Repair Car Battery Charger package includes:
- 1 x EAFC 12V 8A Intelligent Charger unit with integrated power cable and battery clamps.
- 1 x User Manual.
Pure copper core alligator clips for stable current output.
4. Product Specifications
| Feature | Specification |
|---|---|
| Brand | EAFC |
| Product Model | RJ-C120801A |
| Dimensions (LxWxH) | 146 x 81 x 60 mm |
| Net Weight | 420 g |
| Output Line Length | 65 cm |
| Input Line Length | 150 cm |
| Input Voltage | AC110-230V (50-60Hz) |
| Output Voltage | DC13.8-15.5V (Automatic compensation for -15°C to 45°C) |
| Output Current | DC-8A (Max) |
| Applicable Battery Capacity | 12V 2Ah-150Ah |
| Executive Standards | T/TCDZ0001-2019 |
| Compatible Battery Types | Most 12V lead-acid batteries (Calcium, Gel, AGM, Wet, EFB) and LiFePO4 (14.6V+0.2) batteries. |
| Protection Features | Overvoltage, Short Circuit, Reverse Connection, Overcurrent, Fire, Electric Shock, Overheat, Low Voltage |
| Housing Material | ABS Plastic (Flame-retardant) |
Detailed product parameters.
The charger includes multiple safety protection features.
5. Setup Instructions
Follow these steps to correctly set up your EAFC battery charger:
- Connect Battery Clamps:
Attach the red positive (+) clamp to the positive terminal of the battery.
Attach the black negative (-) clamp to the negative terminal of the battery.
Step 1: Connect the battery clamps correctly.
- Connect to Power Supply:
Plug the charger's power cord into a standard AC110-230V (50-60Hz) household power outlet.
The charger with a US plug variant.
- Initial Display: The LCD display will light up, showing the current battery voltage and ambient temperature.
Video Demonstration:
Video demonstrating the connection process, battery status check, and mode selection.
6. Operating Instructions
Once connected, the charger will automatically detect the battery type and begin charging. You can also manually select modes.
- Select Charging Mode:
Press the 'MODE' button to cycle through the available charging modes. Choose the mode that matches your battery type and charging need:- Car/Truck Mode: For standard 12V car and truck batteries.
- AGM/LiFePO4 Mode: Specifically for AGM batteries and LiFePO4 batteries (ensure LiFePO4 has a BMS).
- Motorcycle/Tricycle Mode: For smaller 12V batteries found in motorcycles and tricycles.
- Pulse Repair Mode: For desulfation and recovery of deeply discharged or sulfated batteries.
Use the 'MODE' button for precise switching between charging programs.
- Automatic Temperature Compensation:
The charger features an intelligent temperature sensor. It will automatically switch to:- Winter Mode: Below 30°C (86°F) for optimal cold-weather charging.
- Summer Mode: Above 0-10°C (32-50°F) for optimal warm-weather charging.
The charger automatically optimizes charging based on ambient temperature.
- Monitoring the Charging Process:
The intelligent digital display provides real-time information:- Voltage (V): Current battery voltage.
- Current (A): Charging current.
- Electricity (%): Estimated battery charge level.
- Completion (FUL): Indicates when charging is complete.
- Repair: Displays when pulse repair is active.
The LCD display provides comprehensive charging status at a glance.
- Full Power Self-Stop:
The charger will automatically stop charging once the battery reaches full capacity, preventing overcharge and extending battery life. The display will show "FUL".
Wide range of application for various 12V vehicles and battery types.
7. Care and Maintenance
- Cleaning: Disconnect the charger from power and battery before cleaning. Wipe the exterior with a soft, dry cloth. Do not use harsh chemicals or abrasives.
- Storage: Store the charger in a cool, dry place away from direct sunlight and extreme temperatures. Ensure the cables are neatly coiled and not kinked.
- Cooling System: The charger is equipped with a cooling fan and aluminum heat sink to prevent overheating and extend its lifespan. Ensure the fan port is not obstructed during operation.
The cooling fan port helps extend the charger's life.
- Housing: The charger features an ABS flame-retardant housing, providing durability and fire resistance.
The ABS flame housing ensures durability and safety.
8. Troubleshooting
If you encounter issues with your charger, refer to the following common problems and solutions:
- Charger not turning on: Ensure the power cord is securely plugged into a live outlet and the battery clamps are correctly connected to the battery terminals.
- Display shows an error or protection indicator: The charger has multiple built-in protections (overvoltage, short circuit, reverse connection, overcurrent, overheat, low voltage). Disconnect the charger, check all connections, ensure the battery type is compatible, and allow the unit to cool if overheating is suspected. Reconnect and try again.
- Battery not charging: Verify that the correct charging mode is selected for your battery type. Check the battery's capacity to ensure it is within the 2Ah-150Ah range. If the battery is severely damaged or sulfated, try the Pulse Repair mode.
- LiFePO4 battery warning: If charging a LiFePO4 battery, ensure it has a functional Battery Management System (BMS). Charging without a BMS is prohibited and dangerous.
If the problem persists after following these steps, contact customer support.
9. User Tips
- For optimal battery health, consider using the Pulse Repair mode periodically, especially for older batteries or those that have been deeply discharged.
- Always ensure a stable power supply to the charger for consistent performance.
- The automatic temperature compensation feature means you generally don't need to worry about adjusting settings for different seasons, but it's good to be aware of its function.
- Regularly check the battery terminals for corrosion and clean them if necessary to ensure good contact with the charger clamps.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the contact details provided by your retailer or the manufacturer's official website. Keep your purchase receipt as proof of purchase.
