HLTNC 110SG M06030

Contents

HLTNC 110SG M06030 AC Servo Motor Kit with XP200 Driver User Manual

Model: 110SG M06030

1. Introduction

1.1 Product Profile

The XP200 digital AC servo driver is a leading general AC servo drive product. This series adopts advanced full-digital control and AC motor vector control theory, offering excellent performance and high reliability. These products are widely used in servo shaft drives for food processing, packaging machinery, textile machinery, and other related automatic industrial machinery.

Product Features:

  • High-performance DSC chip and large-scale programmable logic control chip for excellent control performance.
  • Small and exquisite design of XP200 saves installation space.
  • New industrial-grade IPM module with strong overload drive capability.
  • Integrated speed control, position control, and torque control.
  • Compatible with various types of permanent magnet synchronous servo motors.
  • Comprehensive fault protection and status monitoring functions.
  • Excellent low-speed torque characteristics and industry-leading dynamic acceleration and deceleration performance.

2. Product Overview

The HLTNC 110SG M06030 AC Servo Motor Kit includes the servo motor, XP200 servo driver, and necessary cables.

HLTNC AC Servo Motor Kit with XP200 Driver and cables
Figure 2.1: HLTNC AC Servo Motor Kit including motor, driver, and cables.

2.1 Set Content

Set content diagram showing power line, servo driver, and servo motor
Figure 2.2: Diagram illustrating the components included in the kit.
  • Power line code line (3M)
  • EC-XP200-30PL Servo Driver
  • EC-F4CC180V-M2XM*A Servo Motor
Power line code line 3M
Figure 2.3: The included 3-meter power line code line.

3. Specifications

3.1 General Product Properties

Attribute Value
Brand NameHLTNC
Hltnc Model110SG-M06030
Model NumberEC-F4CC180V
TypeServo Motor
PhaseThree-phase
AC Voltage208-230 / 240 V
Output Voltage1.8kw
Rated Current6A
Rated Torque6Nm
Fated Speed3000rpm
Encoder2500line Photoelectric
Driver ModelEC-XP200-30PL
Standard Cable Length3meter
Protect FeatureTotally Enclosed
EfficiencyIE 2
CertificationCCC, CE, NONE
Analog Voltage ControlSupport
RS485Support
Does it include wireless functionality?No
Does it include a Battery?No
High-concerned chemicalNone
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc

3.2 Driver Model Specification (XP200)

XP200 Driver dimensions and product parameters table
Figure 3.1: XP200 Driver dimensions and product parameters.

The XP200 model naming convention is as follows:

  • Driver Series: XP200-Servo Driver Series
  • Voltage Rating: L: 220V, H: 380V
  • IPM Module Capacity: 20-20A, 30-30A
  • Communication type: P: 485 Communication Mode, C: CAN Bus, E: EtherCAT Bus
  • Encoder Communication Mode: None: Parallel communication 2500 lines, R: Serial communication with 17/23 bits.

3.3 Servo Motor Product Parameters

Servo Motor dimensions and product parameters table
Figure 3.2: Servo Motor dimensions and product parameters.
Parameter Value
Model numberEC-F4CC180V-M2XM*A
Rated current (A)6
Rated rev (RPM)3000
Rated power (KW)1.8
Rated torque (Nm)6
Rated voltage (V)220

3.4 Drive Specifications and Performance Parameters

Parameter Description
Input Power SupplySingle-phase/three-phase 220VAC -15%~+10% 50/60Hz
Operating Temperature0°C ~ 40°C
Storage Temperature-40°C ~ 50°C
Operating Humidity40%~80% (no condensation)
Storage HumidityLower than 93% (without moisture condensation)
Atmospheric Pressure86kPa ~ 106 kPa
Protection GradeIP20
Control ModePosition, Speed, Torque, Position/Speed, Speed/Torque, Position/Torque
Digital Input8 programmable input terminals (photoelectric isolation)
Digital Output6 programmable output terminals (photoelectric isolation)
Encoder Signal Output TypeA, B, Z differential output, Z signal open collector output
Input FrequencyDifferential inputs: ≤500kHz (kpps); Single-ended input: ≤200kHz (kpps)
Position Command ModePulse + symbol; Forward/reverse pulse; Orthogonal pulse
Electronic Gear Ratio1~32767/1~32767
Simulation Command Input±10VDC, input impedance 10KΩ
Speed Command Acceleration/DecelerationParameter setting P-060/P-061
Speed Command SourceAnalog quantity, internal speed command
Torque Command Input-10V ~ +10V, input impedance 10KΩ
Torque LimitationParameter setting P-065/P-066
Torque Command SourceAnalog quantity, internal torque command
Monitoring FunctionRotate speed, current position, position deviation, motor torque, motor current, command pulse frequency, etc.
Protection FunctionsOver-speed, over-voltage, over-current, overload, brake abnormality, encoder abnormality, position overshoot, command overclocking, etc.
Velocity Frequency Response≥800Hz
Velocity Fluctuation Rate<±0.03% (load 0~100%); <±0.02% (power -15% ~ +10%)

4. Setup

4.1 Wiring Instructions

4.1.1 Front Panel Terminal Wiring Diagram

XP200 Driver Panel Wiring Diagram
Figure 4.1: Detailed wiring diagram for the XP200 driver panel.

Important Wiring Notes:

  • Motor power lines U, V, W, PE should be connected to the corresponding terminals separately. Do not misconnect.
  • Energy consumption brake resistance should be connected between P and BK terminals.
  • The XP200 series power supply is three-phase AC220V or single-phase 220V.
  • For single-phase power supply, connect the R and T terminals.
  • The main power supply of the driver is connected to the R, S, and T terminals.

4.1.2 Brake Resistance Specification

Standard 220V servo models do not contain built-in resistance. An external brake resistor must be connected, except for custom models.

Driver Model Recommended Configuration (Light Load Type) Recommended Configuration (Overload Type)
XP200-20PL10Ω, power > 60W (Starting/stopping not frequent)≥47Ω, power > 500W (Starting/stopping frequent)
XP200-30PL47Ω, power > 100W (Starting/stopping not frequent)≥47Ω, power > 500W (Starting/stopping frequent)

4.1.3 Definition Diagram of Control Port CN2 and Encoder Port CN3

Control Port CN2 and Encoder Port CN3 Pinout Diagram
Figure 4.2: Pinout definitions for Control Port CN2 and Encoder Port CN3.

Special Attention for Pulse Command Signal:

  • If the pulse command signal is powered by 24V: Connect the 35-pin of CN2 to 24V. Connect the negative terminal of the pulse signal to the 43-pin of CN2. Connect the negative terminal of the direction signal to the 39-pin of CN2.
  • If the pulse command signal is powered by 5V: Do not connect the 35-pin of CN2. Instead, connect PULSE+ to the 41-pin of CN2, PULSE- to the 43-pin of CN2, SIGN+ to the 37-pin of CN2, and SIGN- to the 39-pin of CN2.

4.1.4 Communication Port CN2 Connection Diagram

The digital input interface circuit can be controlled by switches, relays, open-collector transistors, photocouplers, etc. The external voltage range is DC12V to 24V.

Digital Input Interface (C1)

The output circuit adopts Darlington photocouplers and can be connected to relays and photocouplers. Precautions:

  • The power supply is user-provided. Reverse connection will damage the driver.
  • Maximum external power supply voltage: 25V.
  • Maximum output current: 50mA. Total current of three channels should not exceed 100mA.
  • For inductive loads (e.g., relays), a diode must be connected in parallel. Reverse polarity will damage the driver.
  • A voltage drop of about 1V occurs when conducting, which may not meet TTL low-level requirements. Cannot be directly connected to TTL circuits.

5. Operation

5.1 Panel Operation

The XP200 series panel features 5 LED digital tube displays and 4 keys (▲, ▼, ◀, ▶) plus an Enter key, along with POW and RUN LEDs. These are used for displaying and setting system parameters.

5.1.1 Symbols and Functions

Symbol Name Function
POWPower indicatorLit: Main power source power-on; Off: Main power source power-off.
RUNRunning lightLit: Motor in power-on operation; Off: Motor is power-off.
▲Increase keyIncrease sequence number or numerical value; long press for repetitive effect.
▼Decrease keyDecrease sequence number or numerical value; long press for repetitive effect.
◀Exit keyMenu exits; operation cancelled.
EnterConfirmation keyMenu entry; parameter modification confirmation or operation confirmation.
SShift keyQuick modification of parameter number or parameter value (for T3L only).

5.1.2 Main Menu Navigation

The main menu has four modes of operation. Use the ▲ and ▼ keys to change the way. Press Enter to enter the second floor for specific operations. Press the ◀ key to return to the main menu from the second floor.

  • Status (d-): Monitor various operating parameters.
  • Parameter (P-): Set and modify system parameters.
  • Auxiliary (A-): Access auxiliary functions.

5.2 Parameter Setting and Function Debugging

5.2.1 Initial Test Run

When using the drive unit for the first time, it is recommended to perform a test run (keyboard speed regulation or JOG Running) without connecting the load. Ensure the drive unit and servo motor work properly after handling and installation, and that the default parameters of the drive unit adapter are valid.

After the drive unit and motor are working properly, connect the CN1 control terminal without load, and use with the CNC device of the upper computer to debug and run in speed, position, or other modes as needed.

Once signal connection, parameter setting, and motor operation are debugged normally, connect the load and run with load.

5.2.2 Set Motor Code

  1. Modify the operation password (parameter P-000) to 385.
  2. Modify the motor Code (parameter P-002) according to the motor model. Refer to the Motor Adaptation Table in Section 3.4.
  3. Enter parameter management and perform the reset default values action.

Special attention: The operation to restore default values must be carried out when the driver is not enabled, otherwise an Error will be displayed.

After successful panel display operation, turn off the power supply, wait for the drive panel to extinguish, then turn on the power supply again to proceed with the next operation (keyboard speed test running or JOG running).

5.2.3 Trial Run (Keyboard Speed Regulation & JOG Spot Test)

After confirming no alarms or exceptions, operate as follows:

  • Keyboard Speed Regulation: The panel displays 'r.' (r/min). Use ▲/▼ keys to change speed. Positive numbers indicate forward rotation (CCW), negative numbers indicate reverse rotation (CW). Minimum speed is 0.1 r/min. If the motor runs normally, you can enter spindle control parameter settings.
  • JOG Spot Test: Turn on main circuit power. Set P-098 to 1 (servo enable SON). The RUN indicator will light. In the auxiliary function menu 'A-', select 'A-JOG' and press Enter. The jog prompt 'J' will appear. Press and hold ▲ for JOG speed (CCW), release to stop. Press and hold ▼ for JOG speed reverse (CW), release to stop. JOG speed is set by parameter P-076 (default 100r/min).

5.2.4 Coordinate with PC Controller

The servo driver operates in three modes: Position, Speed, and Torque mode.

  • Position Control Mode: For precise positioning (e.g., CNC machine tools). Uses pulse commands (PULS+, PULS-, SIGN+, SIGN-).
  • Speed Control Mode: For precise speed control (e.g., knitting machines). Can form closed-loop control with upper device.
  • Torque Control Mode: For printing, winding, injection molding machines. Motor output torque is proportional to input command.

Refer to the full manual PDF for detailed parameter settings for each control mode: User manual (PDF).

6. Maintenance

6.1 Electromagnetic Brake

The electromagnetic brake (holding brake and power loss brake) is used to lock vertical or inclined worktables to prevent falling after servo power loss. A motor with a brake is required for this function. Brakes are for holding, not for slowing down or stopping movement.

Parameter Name Scope Default Values Unit Applicable
P165Motor static speed detection point0~10005r/minALL
P166Delay time of electromagnetic brake when motor is stationary0~2000200msALL
P167Waiting time of electromagnetic brake when motor is running0~2000500msALL
P168Operating speed of electromagnetic brake when motor is running0~3000100r/minALL
P169Delay time for release of electromagnetic brake0~3000200msALL

6.1.2 Use of Electromagnetic Brake

The brake wiring diagram shows the brake release signal BRK of the driver connected to the relay coil, and the relay contact connected to the brake power supply. The brake power supply is user-provided and must have sufficient capacity. It is recommended to install a surge absorber to suppress surge voltage. Diodes can also be used as surge absorbers. Note that there may be a slight braking delay.

When the motor is stopped and stationary (speed less than P-165), and the servo is turned OFF, the motor remains energized to maintain position. The brake is released. After a stabilization period (P-166), motor power is removed.

When the motor is running (speed higher than P-165) and servo is OFF, motor current is cut off, and the brake remains released. After a delay, the brake is applied. This reduces motor speed from high to low before mechanical brake actuation, preventing damage. The delay time is determined by P-167 or motor speed deceleration to P-168, whichever is minimum.

P-169 defines the delay time from motor current opening to electromagnetic brake release (DO output terminal BRK ON) when the system transitions from non-enabled to enabled state.

6.2 General Care

Regularly inspect all connections for tightness and signs of wear. Keep the driver and motor free from dust and debris to ensure proper cooling and operation. Avoid exposing the unit to excessive moisture or extreme temperatures.

7. Troubleshooting

7.1 Alarm Codes

The XP200 driver has comprehensive fault protection. When an alarm occurs, the driver will display an alarm code. Refer to the table below for common alarm codes and their meanings.

Alarm Code Alarm Name Alarm Content Alarm Clearable
Err--No alarmWorking normally
Err 1SpeedingMotor speed exceeds maximum limitYES
Err 2Power main circuit over voltageMain circuit power supply voltage exceeds the specified maximum valueNO
Err 3Power main circuit under voltageMain circuit power supply voltage is lower than the specified minimum valueNO
Err 4Position following-deviation too largeThe value of the position deviation counter exceeds the set valueYES
Err 5Position command over clockingPosition command frequency exceeds the highest frequencyYES
Err 6Motor stallMotor shaft is blocked, or wiring is incorrect, or pole pair setting is incorrect, or encoder line number is incorrect.YES
Err 8Speed response failureExcessive spindle load makes the speed deviation too large, or pole pair setting is incorrect, or encoder line number is incorrect.YES
Err 9Incremental encoder AB signal errorMotor encoder AB signal has interference or disconnectionNO
Err11IPM module over currentMain circuit IPM (inverter) module over current or over heat.NO
Err12Over currentServo driver instantaneous current is too large.NO
Err13Over loadMotor average load current is too large.NO
Err14Brake peak power overloadBrake instantaneous load is too large.NO
Err16Motor thermal overloadMotor heating value exceeds the set value (I²t detection).NO
Err17Brake average power overloadBrake long-term average load is too large.NO
Err18Power module overloadPower module output average load is too large.NO
Err20EEPROM errorEEPROM read and write error.NO
Err21Logic circuit errorProcessor peripheral logic circuit error.NO
Err23AD conversion reference voltage errorAD sampling circuit voltage reference is not a standard value.NO
Err24AD conversion channel is asymmetrical or zero drift too largeAD sampling amplification conditioning circuit is abnormal.NO
Err25Motor code errorMotor code setting is not suitable.NO
Err29User torque overload alarmMotor load exceeds user-set value and duration.YES
Err30Encoder Z signal lossEncoder Z signal does not appear.NO
Err31Encoder Z signal detection is abnormalEncoder Z signal has interference or signal instability.NO
Err32Encoder UVW signal illegal codingThe motor encoder UVW signal is missing, and the Z signal can be manually turned off to cancel the alarm.YES
Err34Spindle orientation failureSpindle orientation function is running incorrectly.YES
Err35Spindle encoder (second encoder) errorSpindle encoder AB polarity error.NO
Err36Spindle encoder (second encoder) line is brokenSpindle encoder line is broken or there is interference.NO

7.2 Alarm Cleanup Method

When a fault alarm occurs, after troubleshooting the cause, the alarm can be cleared via the drive operating panel while power is still on. The specific method is:

Without an active alarm, set parameter P-119 to 4. Then, follow the steps on the panel to clear the history alarm code. Note: Some hardware failure alarms cannot be cleared and require consultation with technicians.

7.3 Common Problems and Countermeasures

  • Error restoring default parameters:
    • Confirm operation password (P-000) is set correctly.
    • Default restoration must be done when the driver is not enabled.
  • Upper computer enabled, but driver's green RUN light is off:
    • Check R/S/T power supply voltage.
    • Check CN1 interface 31 feet for +24V.
    • Check if SON signal is connected to 0V at pin 16 of CN1 interface.
    • If the RUN light remains off, try using the internal enable (P098 set to 1).
  • "Err-9/Err-10/Err-30/Err-31/Err-32/Err-33" fault alarm (Encoder issues):
    • Check encoder or encoder connection cable.
    • Ensure both ends of shielding layer are well grounded and free from water/impurities.
    • Verify connecting line length to prevent 5V encoder power supply attenuation.
    • Isolate from strong magnetic/electric interference.
  • Noise or vibration (high frequency) during servo motor operation:
    • Increase filter coefficients P-007 and P-019 by 5 per adjustment.
    • If not effective, reduce speed loop proportional gain and position loop proportional gain (P-005 and P-009) by 5 per adjustment.
    • Check for interference in encoder connection line and shielding layer grounding.
  • Jitter (low frequency) in servo motor operation:
    • Verify load and inertia are within allowable range (load torque > 3 times, inertia > 5 times may require larger motor).
    • Adjust proportional gain P-005 of the speed ring by 5 per adjustment.
    • If not effective, decrease filter coefficient P-007/P-019 by 5 per adjustment.
    • If not effective, reduce position loop gain P-009 by 5 per adjustment.
    • Check for interference in encoder/command connection lines and shielding layer grounding.
  • Driver has "Err-2" or "Err-11" alarm:
    • If alarm on power-up, hardware circuit failure.
    • If alarm during frequent acceleration/deceleration of large inertia, check current (d-I, d-pl). Reduce inertia acceleration (increase P-060, P-061) to keep current within range.
  • "Err-5/Err-12" appears when servo motor starts:
    • Err-5: Pulse command frequency too fast. Increase acceleration/deceleration time or position command smoothing time P-040 by 10 per adjustment.
    • If measures fail, set P-116 to 32 to shield "Err-5" alarm (power cycle required).
    • Err-12 (overcurrent): Motor overloaded during startup. Check driver type/damage.
  • "Err-4" appears during servo motor operation:
    • If low-speed normal, high-speed Err-4: Check P-075 (max rotation speed limit). Adjust P-009 (position loop gain) or P-080 (position overshoot detection range).
    • If only position command given, Err-4 appears: Check if motor is locked/damaged, or if strong current circuit is damaged.
    • If Err-4 during rapid acceleration: Driver/motor selection too small.
    • If occasional Err-4: Check encoder/command connection line interference and shielding layer grounding.
  • Driver running normally, but upper computer has "too large position tracking error":
    • Set P-080 (actuator position overrun detection range) to a value smaller than the detection threshold. Observe if "Err-4" appears.
    • If no "Err-4" in driver, interference in encoder signal to upper computer. Check connection line welding and shielding layer grounding.
    • If "Err-4" in actuator: Response problem of actuator/motor. Confirm driver/motor integrity. Adjust P-009/P-005 (position/speed ring gain).
    • If measures fail, consider larger driver/motors.

8. User Tips

No specific user tips were available from reviews or Q&A for this product at this time.

9. Warranty & Support

For warranty information and technical support, please contact the seller directly through the platform where the product was purchased. Ensure to provide your order details and product model number for efficient assistance.

You can also refer to the comprehensive user manual PDF for more detailed instructions and diagrams: User manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.