1. Introduction
The RadioMaster AG01 Nano Full CNC Hall Gimbal Set is a high-precision upgrade designed specifically for the RadioMaster Pocket radio. Crafted from billet CNC aviation-grade aluminum, these gimbals offer superior durability, accurate control, and an enhanced stick feel. This manual provides essential information for installation, adjustment, and general use of your new gimbal set.
2. Key Features
- Made with billet CNC aviation grade aluminum for superior durability and outstanding looks.
- Non-contact Hall sensors with precise centering for accurate control.
- Quad precision bearings for unparalleled stick feel.
- Adjustable vertical travel angle (Min. 38°, Max. 54°).
- Specifically designed for the smaller RadioMaster Pocket radio.
- Replaceable M3 threaded stick ends.





3. Specifications
| Attribute | Value |
|---|---|
| Item | AG01 NANO CNC Hall Effect Gimbal |
| Sensor type | Non-contact hall effect |
| Working voltage | DC 3.3V |
| Linearity | Real-time (No latency) |
| Adjustable vertical travel range | 38°- 54° |
| Self-centering adjustment | Yes |
| Mode adjustment | Yes |
| Adjustable tension | Yes |
| Bearing | Quad precision bearings |
| Temperature range | -20°C-85°C |
| Size | 42 x 37 x 43mm |
| Weight | 32g (±0.3g) |


4. Package Contents
The AG01 Nano Full CNC Hall Gimbal Set package includes:
- 2 x AG01 NANO CNC Hall Effect Gimbal
- 2 x L-shaped Hexagon Socket Screwdriver
- 4 x Hard Tension Spring
- 8 x PB2*6 Screw
- 2 x CM1.6*3 Screw
- 2 x Manual

5. Installation
The AG01 Nano Gimbals are designed for easy installation into the RadioMaster Pocket radio. It is recommended to watch an installation video on YouTube for a visual guide. You will need a 2.0mm Allen wrench screwdriver and a four-head Phillips screwdriver in addition to the included tools.
- Carefully open your RadioMaster Pocket radio according to its service manual or an online guide.
- Locate the existing gimbals and disconnect their wiring.
- Unscrew and remove the old gimbals.
- Position the new AG01 Nano Gimbals into place.
- Connect the gimbal wiring to the appropriate ports on the radio's mainboard.
- Secure the new gimbals using the provided screws (PB2*6 and CM1.6*3).
- Ensure all connections are firm and no wires are pinched before reassembling the radio.
- Test the gimbal functionality before fully closing the radio casing.

Installation Video Guide
For a detailed visual walkthrough of the installation process, please refer to the official product video:
6. Adjustments
The AG01 Nano Gimbals offer several exterior adjustments to fine-tune your control experience. These adjustments are typically made after installation and before final assembly of your radio.

6.1. Adjusting Maximum Travel (Throttle / Elevator)
To change the maximum travel of the gimbal (for throttle or elevator axes), adjust screws labeled ① and ② in the diagram:
- Turn the screw clockwise to decrease travel.
- Turn the screw counter-clockwise to increase travel.

6.2. Mode Adjustment (Self-Centering / Non-Self-Centering)
Position ③ allows you to change the gimbal's mode:
- Adjust Position ③ to switch the gimbal from self-centering (typically for elevator) mode to non-self-centering (typically for throttle) mode.
6.3. Adjusting Spring Tension
Position ④ is used to adjust the spring tension:
- Turn the screw clockwise to increase tension.
- Turn the screw counter-clockwise to decrease tension.
7. Maintenance
To ensure the longevity and optimal performance of your AG01 Nano Gimbals, follow these maintenance guidelines:
- Keep the gimbals clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Avoid exposing the gimbals to extreme temperatures or moisture. The recommended operating temperature range is -20°C to 85°C.
- Periodically check all screws for tightness, especially after initial installation and extensive use.
- Do not apply lubricants unless specifically recommended by RadioMaster, as this could interfere with the Hall effect sensors.
- Handle the gimbals with care to prevent physical damage.
8. Troubleshooting
If you encounter issues with your AG01 Nano Gimbals, consider the following:
- Gimbal not responding: Double-check all wiring connections to ensure they are secure and correctly plugged in. Verify that the radio's firmware is up to date and compatible with the gimbals.
- Inconsistent movement or centering: Ensure the gimbals are properly calibrated within your radio's settings. Check for any physical obstructions or debris affecting the gimbal's movement. Re-adjust the spring tension and self-centering mechanism as needed.
- Gimbal feels stiff or loose: Adjust the spring tension using position ④ as described in the 'Adjustments' section.
- Gimbal travel limits are incorrect: Adjust the maximum travel using positions ① and ② as described in the 'Adjustments' section.
If problems persist, consult the RadioMaster support resources or community forums for further assistance.
9. User Tips
- Many users find these gimbals to be a significant upgrade over factory-installed gimbals, offering a smoother and more precise control experience.
- When installing, it's highly recommended to watch a video tutorial online. While the process is generally straightforward, visual guidance can be very helpful.
- Ensure you have the necessary tools: a 2.0mm Allen wrench screwdriver and a four-head Phillips screwdriver are commonly needed in addition to the included L-shaped Hexagon Socket Screwdriver.
- The AG01 Nano Gimbals are specifically designed for the RadioMaster Pocket radio. Compatibility with other radio models, such as the Jumper T8SG, is not guaranteed and may require modifications.
10. Warranty and Support
For information regarding product warranty, technical support, or service, please refer to the official RadioMaster website or contact their customer service directly. Keep your proof of purchase for any warranty claims.