SOLONG Tattoo SL-M2-E96S-1

Contents

Solong Tattoo Wireless Tattoo Pen Machine

Model: SL-M2-E96S-1

User Manual

1. Introduction

This manual provides essential information for the safe and effective use of your Solong Tattoo Wireless Tattoo Pen Machine. Please read all instructions carefully before operation.

For a detailed user manual in PDF format, please refer to the official document: User Manual (PDF).

2. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product, skin injury, infection, or other personal injury.

  • Warning: Keep the tattoo machine, needles, power supply, and all accessories out of reach of children under 12 years old. This product is for professional use only and not for children's play.
  • Keep away from children and pets at all times during use, and no unsupervised use by minors or untrained personnel.
  • Do not use this product for purposes other than its intended use (tattooing on human skin); do not use for animal marking, material engraving, or other non-skin tattooing applications.
  • Inspect the product, including the machine body, needle bar, power cord, and connection parts before each use; do not use if damaged, deformed, loose, or malfunctioning.
  • Follow professional installation and operation guidelines strictly to avoid needle stick injuries, excessive skin puncture, or other bodily harm.
  • Do not expose the tattoo machine body, power supply, or control panel to water, moisture, direct sunlight, or high humidity environments to prevent short circuits, electric shock, or product damage.
  • Handle tattoo needles, needle bars, and other sharp accessories with extreme care to avoid cuts, needle stick injuries, or cross-infection.
  • Warning: Use only original and certified matching accessories (needles, power supply, grip) provided by the manufacturer; non-matching accessories may cause machine failure, skin injury, or fire hazard.
  • Warning: Disinfect the tattoo machine's contact parts and accessories thoroughly before and after each use in accordance with professional disinfection standards to prevent cross-infection of bacteria and viruses.
  • Do not operate the tattoo machine with wet hands to avoid electric shock risk.
  • Stop using the machine immediately if abnormal noise, overheating, or needle jamming occurs, cut off the power supply, and check the fault before reusing.
  • This product is for professional tattoo artists only; novice users must receive systematic professional training before use.
  • Do not use the tattoo machine on damaged, inflamed, allergic, or sensitive skin to avoid aggravating skin damage.

3. Package Contents

The package includes the following items:

  • 1 x Solong Tattoo Wireless Tattoo Pen Machine
  • 1 x USB-C Charging Cable
  • 2 x Hex Wrenches
  • 3 x O-rings
  • 1 x User Manual (this document)
Solong Tattoo Wireless Tattoo Pen Machine and accessories
Image 1: Package contents including the tattoo pen, charging cable, wrenches, and O-rings.

4. Specifications

FeatureDetail
Product NameTattoo Pen
Model NumberSL-M2-E96S-1
ColorBlack
MotorHollow Cup Motor
Voltage Range4-12V
Battery Capacity1800mAh
Use Time5-6 hours
Needle Stroke (Adjustable)2.4, 2.7, 3.0, 3.3, 3.6, 3.9, 4.2 mm (1-4.5mm range)
Weight232g
Charging PortUSB-C
MaterialAluminum
Commodity Quality CertificationCE, UL
Detailed product parameters table
Image 2: Visual representation of the product parameters.
Dimensions of the tattoo pen machine
Image 3: Product dimensions: 13.6cm (5.35in) length, 3.8cm (1.49in) width.
Internal view of the hollow cup motor
Image 4: Illustration of the Hollow Cup Motor, showing 8V 6500RPM speed and 4-12V voltage.

5. Setup

5.1 Before First Use

  1. Remove all protective films and packaging materials from the tattoo machine body, grip, and power supply.
  2. Disassemble the detachable parts (grip, needle bar) and perform high-temperature and high-pressure disinfection or professional disposable disinfection treatment in accordance with medical disinfection standards.
  3. Ensure all parts are dry before assembly.

5.2 Accessory Assembly

  1. Insert the sterilized tattoo needle into the needle bar, and fix it tightly with the locking nut to prevent the needle from loosening during operation.
  2. Connect the assembled needle bar to the tattoo machine body, adjust the needle stroke (0.8-4.0mm adjustable) according to the tattooing needs (lining/shading), and lock the adjustment knob.
  3. Screw the disinfected grip onto the machine body to ensure a firm connection without looseness.

5.3 Power Connection

Connect the DC power cord of the tattoo machine to the matching certified power supply (input: 100-240V AC, 50/60Hz; output: 0-18V DC), plug the power supply into a grounded power socket, and ensure the power switch is in the "OFF" position before connection.

Tattoo pen controls and charging port
Image 5: Overview of the tattoo pen's controls, including Voltage "+", Power button, Voltage "-", and Mode Switching. Also highlights the Type-C charging interface.
Wireless tattoo pen machine with separate power unit
Image 6: The wireless tattoo pen machine shown with its detachable power unit.

6. Operating Instructions

6.1 Parameter Adjustment

Turn on the power supply switch. Adjust the voltage according to the tattooing demand:

  • Lining: Recommended to set 6-10V.
  • Shading: Recommended to set 4-8V.

Test the machine's running state by pressing the foot pedal. Adjust the needle speed and stroke to the appropriate state, and ensure the needle does not jam or shake abnormally.

6.2 Operation

  1. Hold the tattoo machine grip with a firm and comfortable grip, keeping the machine at a 15-45° angle to the skin surface during tattooing.
  2. Control the machine by stepping on the foot pedal (foot pedal control is the default mode). Release the foot pedal to stop the machine running. Avoid long-time continuous operation to prevent machine overheating.
  3. Move the machine evenly and slowly on the skin. Do not stay in the same position for a long time to avoid excessive skin puncture and blistering.

6.3 Instant Start-up Mode

If the lighting mark is displayed, the instant start-up mode will be turned on. Quickly double-click the power button to start the machine in instant start-up mode.

Instant start-up mode display on tattoo pen
Image 7: Display showing the instant start-up mode indicator. Double-click the power button to activate.

Video 1: Unboxing and basic operation demonstration of the wireless tattoo pen machine.

7. Maintenance

7.1 After Use

  1. Step on the foot pedal to stop the machine, turn off the power supply switch, and unplug the power cord from the socket in sequence.
  2. Disassemble the used needle and dispose of it in a sealed sharp object container in accordance with medical waste disposal standards (do not reuse disposable needles).
  3. Disassemble the grip, needle bar, and other detachable parts, and perform disinfection and cleaning treatment immediately.
  4. Wipe the machine body and power supply with a dry, alcohol-disinfected soft cloth to remove ink and dirt (do not use water or detergent to clean directly).

7.2 Storage

After cleaning and disinfection, dry all parts completely. Assemble the machine body (without needle) and store it in a dry, cool, dust-free storage box. Store the power supply, unused sterilized needles, and accessories in a sealed container separately, and keep away from high temperature, moisture, and direct sunlight.

7.3 Routine Maintenance

Lubricate the machine's bearing and moving parts with special lubricating oil every 50 hours of use to ensure smooth operation. Check the power cord for wear and tear regularly, and replace it immediately if damaged.

8. Troubleshooting

No specific troubleshooting steps are provided in the available documentation. If you encounter issues, please ensure all connections are secure, the battery is charged, and you are using compatible accessories. If problems persist, contact customer support.

9. User Tips

No specific user tips were available from buyer reviews or Q&A content.

10. Warranty and Support

For warranty information and customer support, please refer to the manufacturer's official website or contact the seller directly. Ensure you retain your proof of purchase for any warranty claims.

Manufacturer: Tattoo Tech Co., Ltd.

Website: www.tattootech.com

EU Authorized Representative: EU AR Service GmbH

Website: www.tattooservice.eu

© 2024 Solong Tattoo. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.