ZUOYA GMK26

Contents

ZUOYA GMK26 QMK/VIA Gasket Number Pad User Manual

Model: GMK26

Introduction

Thank you for choosing the ZUOYA GMK26 QMK/VIA Gasket Number Pad. This manual provides detailed instructions for setting up, operating, maintaining, and troubleshooting your new mechanical numpad. Please read this manual thoroughly to ensure optimal performance and a satisfying user experience.

ZUOYA GMK26 Digital Area Pad, three-mode mechanical keyboard kit with RGB backlight and QMK/VIA support.
Figure 1: ZUOYA GMK26 Digital Area Pad, three-mode mechanical keyboard kit with RGB backlight and QMK/VIA support.
Key features of the GMK26 numpad: QMK/VIA support, PBT keycaps, RGB backlight, independent stabilizer, hot-swappable switches, and south-facing LED lights.
Figure 2: Key features of the GMK26 numpad.

Setup

The ZUOYA GMK26 supports three connection modes: Wired, Bluetooth 5.0, and 2.4GHz Wireless. Ensure the mode switch, located near the USB port, is set correctly for your desired connection type.

1. Wired Mode

  1. Locate the mode switch on the side of the numpad.
  2. Toggle the mode switch to the middle position (Wired Mode).
  3. Connect the USB cable from the numpad to your computer.
  4. The keyboard backlight will illuminate and display the default RGB effect, indicating a successful connection.

2. Bluetooth® Pairing

The GMK26 can connect to up to three Bluetooth devices simultaneously.

  1. Toggle the mode switch to the left position (Bluetooth Mode), closer to the USB port.
  2. Press and hold FN + 1, FN + 2, or FN + 3 for 3-5 seconds to enter pairing mode. The corresponding key (1, 2, or 3) will flash blue rapidly.
  3. On your device (computer, tablet, etc.), open Bluetooth settings and scan for available devices.
  4. Select one of the following device names to pair: "ZUOYA GMK26-1", "ZUOYA GMK26-2", or "ZUOYA GMK26-3".
  5. Once connected, the flashing key on the numpad will stop, indicating successful pairing.
  6. To switch between paired Bluetooth devices, short press FN + 1, FN + 2, or FN + 3.

Note: The Bluetooth connection has memory. If the numpad is powered off and then on again, it will automatically reconnect to the last used device.

3. 2.4Ghz Wireless Connection

  1. Toggle the mode switch to the right position (2.4G Mode).
  2. Insert the 2.4Ghz USB receiver into an available USB port on your device.
  3. The "4" key LED will light green for 3 seconds, and the entire keyboard backlight will illuminate, indicating a successful 2.4Ghz connection.

2.4Ghz Re-pairing Instruction (if needed):

  1. Ensure the numpad is in 2.4Ghz Wireless Mode.
  2. Press and hold FN + 4 to enter 2.4G pairing mode. The "4" key will flash green rapidly.
  3. While the "4" key is flashing, insert the 2.4Ghz USB receiver into your computer's USB port.
  4. Upon successful connection, the "4" key will stop flashing and resume the current backlight color.
Image showing PBT wear-resistant keycaps and the mode switch with USB receiver storage compartment.
Figure 3: Mode switch and USB receiver storage compartment.

Operating Instructions

Default Hot Keys (FN Combinations)

Hold the FN key and press the corresponding key to activate the following functions:

  • FN + +: Increase LED backlight brightness
  • FN + -: Decrease LED backlight brightness
  • FN + /: Decrease LED backlight hue
  • FN + *: Increase LED backlight hue
  • FN + 7: Decrease LED backlight speed
  • FN + 8: Increase LED backlight speed
  • FN + BACKSPACE: Toggle backlight ON/OFF
  • FN + ENTER: Toggle backlight mode
  • FN + 5: Increase LED backlight saturation
  • FN + 6: Decrease LED backlight saturation
  • FN + 0: (Long press for 3 seconds) Reset keyboard to factory settings

Macro Keys (M1-M5)

The five keys on the left side (M1-M5) are pre-configured with default macro functions. These can be customized using the VIA software.

  • M1: CTRL + Z (Undo)
  • M2: CTRL + X (Cut)
  • M3: CTRL + C (Copy)
  • M4: CTRL + V (Paste)
  • M5: WIN + D (Display desktop / Toggle current state)

QMK/VIA Customization

The ZUOYA GMK26 supports key remapping and macro programming via QMK/VIA firmware. This allows for extensive customization of your numpad's functionality.

Note: Ensure your keyboard is correctly plugged into your computer device before proceeding with VIA software.

VIA Installation Steps:

  1. Visit https://github.com/WestBerryVIA/via-releases/releases to download the latest VIA application compatible with your computer's operating system.
  2. Download the ZUOYA GMK26.JSON file from the distributor's website.
  3. Open the VIA software. Click 'File' and then 'Import Keymap' to load the downloaded JSON file.
  4. If the VIA software successfully connects and displays your keyboard layout, the installation is complete.
Screenshot of the QMK/VIA software interface for customizing keyboard keys.
Figure 4: QMK/VIA software interface for key customization.

Key Remapping:

On the top half of the VIA software interface, click to select the key you wish to change. Then, on the bottom half, select the new function you want to assign to that key.

Macros Setting:

While the ZUOYA GMK26 does not have dedicated physical multimedia keys, you can remap any key to a macro function using the VIA software. This allows for custom shortcuts and complex command sequences.

Layer Functionality:

The ZUOYA GMK26 is configured with 4 layers (0 to 3) by default. Each key can have multiple functions across these layers, which is particularly useful for compact keyboards.

  • Layer 0: This is the default layer, active when the keyboard is connected to a device.
  • Layer 1: Activated by long-pressing the MO(1) key.
  • Layer 2: To activate, first remap any key to MO(2) using VIA firmware. Then, long-press the assigned MO(2) key.
  • Layer 3: To activate, first remap any key to MO(3) using VIA firmware. Then, long-press the assigned MO(3) key.

QMK Firmware Update Method

To update the QMK firmware:

  1. Ensure the numpad is in Wired Mode.
  2. Press and hold the knob while plugging in the USB cable.
  3. The keyboard will enter DFU (Device Firmware Upgrade) mode, allowing for firmware updates.

Maintenance

Auto Sleep Mode

  • After 5 minutes of inactivity (no keypresses), the backlight will turn off to conserve battery. Press any key to wake the numpad and restore the backlight.
  • After 30 minutes of inactivity in Bluetooth mode, the numpad will enter deep sleep, and the Bluetooth connection will disconnect. Press any key to exit deep sleep mode; the RGB backlight will turn on, and the Bluetooth connection will re-establish.

Battery Charging and Level Indicator

  • Low Battery: When the battery voltage drops below 3.5V, the FN key will flash red continuously to indicate a low battery and the need for charging.
  • Check Battery Level: Press and hold FN + . (period key) to check the battery and charging status. Keys 1 through 0 will light up, representing 10% to 100% battery charge (estimate only). Release the keys to exit this mode.
  • Charging Status: While charging, the FN key will display a red light. Once fully charged, the FN key will turn green.

Cleaning

To clean your numpad, gently wipe the keycaps and casing with a soft, damp cloth. For deeper cleaning, you may carefully remove the keycaps. Avoid using harsh chemicals or abrasive materials that could damage the surface or keycap legends.

Troubleshooting

VIA Software Not Recognizing Keyboard

  • Ensure the numpad is properly connected via USB in Wired Mode.
  • Verify that you have downloaded and imported the correct ZUOYA GMK26.JSON file into the VIA software.
  • If issues persist, please contact customer service for assistance.

2.4Ghz Wireless Connection Issues

  • Try the 2.4Ghz re-pairing instruction detailed in the Setup section.
  • Ensure the USB receiver is securely plugged into your device.
  • Check for potential interference from other wireless devices.

Bluetooth Connection Drops or Fails to Connect

  • Ensure the numpad is sufficiently charged.
  • Re-attempt the Bluetooth pairing process.
  • Remove the numpad from your device's Bluetooth list and re-pair.
  • Ensure no other devices are actively trying to connect to the same Bluetooth slot.

Backlight Not Working

  • Check if the numpad is in auto-sleep mode (press any key to wake).
  • Use FN + BACKSPACE to toggle the backlight on/off.
  • Ensure the numpad is charged.

Specifications

Feature Specification
Connectivity Bluetooth 5.0, 2.4GHz Wireless, Wired (USB)
Keycup Material PBT plastic
Keycup Printing Dye-sublimation
Switches Hot swappable
Backlight Type Multicolor (RGB)
Axis Body Brand zuoya
Keyboard Standard Mini Keyboard
Application Desktop, Laptop, Number, Tablet
Battery Included
Operation Style Mechanical
Language English
Interface Type USB
Product Dimensions 11.8cm (W) x 14cm (H) x 3cm (D), 1.8cm (Front Height)
Package Weight 0.53 kg

Switch Specifications (from image)

  • Total stroke: 3.6 ± 0.3mm
  • Trigger stroke: 2.00 ± 0.5mm
  • Trigger force: 42 ± 5gf
  • Starting force: 30gf Min
  • Bottom contact force: 50gf Max
  • Switch lifespan: 60 million times
Detailed switch specifications including total stroke, trigger stroke, trigger force, starting force, bottom contact force, and switch lifespan, alongside a force-travel graph.
Figure 5: Switch specifications and force-travel graph.
Dimensions of the GMK26 numpad: 14cm (height), 11.8cm (width), 3cm (thickness), and 1.8cm (front height).
Figure 6: Product size diagram.
Exploded view of the GMK26 numpad components: knob, top cover, positioning board, Poron cotton, ixpe pad, PET film, circuit board, sponge, and bottom shell.
Figure 7: Exploded view of the GMK26 numpad components.

Warranty & Support

For detailed item guides and documents, including a PDF user manual, please refer to the official product page or the provided PDF link:

User Manual (PDF)

If you encounter any difficulties with the VIA software or require further assistance, please contact ZUOYA customer service.

User Tips

  • VIA Customization: While VIA offers powerful customization, some users find it challenging initially. Take your time to understand the interface and layer functionality. Refer to the detailed instructions in this manual and the official PDF for guidance.
  • Battery Management: Regularly check the battery level using FN + . to avoid unexpected power loss, especially when using wireless modes.
  • Experiment with Backlight: Utilize the various FN key combinations to explore different RGB backlight effects, hues, and saturations to personalize your numpad's appearance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.