YABER 2000A Peak Current Car Jump Starter

Introduction

This manual provides essential information for the safe and effective use of your YABER 2000A Peak Current Car Jump Starter. Please read all instructions carefully before operating the device and retain this manual for future reference.

The YABER 2000A Jump Starter is a versatile device designed to jump-start 12V vehicles with up to 7.0L gas or 5.5L diesel engines. It also functions as a portable power bank and features a multi-mode LED emergency light.

Image: YABER Jump Starter highlighting its key features: 2000A peak current, 13800mAh power bank, 3-mode LED light, and 10 super safety protections.

What's in the Box

Verify that all items are present in your package:

• Portable Jump Starter
• Safety Jumper Cables (Smart Clip)
• USB-C Charging Cable
• Portable Storage Bag
• User Manual (this document)

Image: Visual representation of the package contents, including the jump starter, jumper cables, USB-C cable, storage bag, and user manual.

Specifications

Image: Diagram illustrating the powerful start performance, showing compatibility with engine sizes from 1.5L to 7.0L.

Safety Information

Always observe the following safety precautions to prevent injury or damage to the device and vehicle:

• Read and understand all instructions before use.
• Ensure the jump starter is fully charged before attempting to jump-start a vehicle.
• Do not connect the red and black clamps together, as this may cause sparks or damage.
• Avoid reverse polarity connections. Always connect the red clamp to the positive (+) terminal and the black clamp to the negative (-) terminal.
• Do not expose the device to rain, water, or extreme temperatures.
• Keep the device out of reach of children.
• If the jump starter becomes excessively hot during use, discontinue operation immediately.
• The device features 10 smart protections to ensure safe operation, including protection against over-current, short-circuit, over-charge, and reverse polarity.

Image: Close-up view of the red and black jumper clamps, emphasizing the 10 safety protections integrated into the device.

Setup

Charging the Jump Starter

Before first use, fully charge the YABER Jump Starter. It is recommended to recharge the device after each use or every 3-6 months if not used, to maintain optimal battery health.

1. Connect the provided USB-C charging cable to the USB-C input port on the jump starter.
2. Connect the other end of the USB-C cable to a suitable USB power adapter (not included) or a powered USB port.
3. The LED indicators on the jump starter will illuminate to show the charging progress. All indicators will be solid when fully charged.

Image: The YABER Jump Starter functioning as a portable power bank, charging a smartphone and a laptop via its USB ports.

Operating Instructions

Jump Starting a Vehicle

Follow these steps to safely jump-start your 12V vehicle:

1. Insert the Smart Clip: Plug the blue end of the smart clip cable firmly into the jump starter's jump-start port. Ensure a secure connection.
2. Connect to Car Battery: Attach the red (+) clamp to the positive terminal of your car battery and the black (-) clamp to the negative terminal. Ensure the clamps make good contact with the battery terminals.
3. Start Your Engine: Once the clamps are correctly connected, start your vehicle's engine. If the engine does not start immediately, wait a few seconds and try again. For very low voltage batteries, the 'Force Start Function' can be activated (refer to device specific instructions for activation, typically a button press).
4. Remove Clamps: After the engine starts, immediately remove the clamps from the car battery, first the black (-) clamp, then the red (+) clamp. Disconnect the smart clip from the jump starter.

Image: Four-step visual guide on how to jump-start a car engine: 1. Insert smart clip, 2. Connect to car battery, 3. Start engine, 4. Remove clamps.

Using as a Portable Power Bank

The YABER Jump Starter can charge various electronic devices:

• USB-A Output: Connect your device's USB charging cable to the USB-A output port (5V 2.1A) on the jump starter.
• USB-C Input: The USB-C port (5V 1.5A) is primarily for charging the jump starter itself.

Image: The YABER Jump Starter acting as a portable power bank, showing USB-A output and USB-C input ports for charging other devices and the unit itself.

Using the LED Emergency Light

The built-in LED light offers three modes for various situations:

• Flashlight: Provides steady illumination.
• SOS Mode: Emits an SOS signal in Morse code for emergencies.
• Strobe Mode: Flashes rapidly for signaling or warning.

To operate the LED light, press the power button briefly to cycle through the modes (Flashlight > SOS > Strobe > Off).

Image: A person using the YABER Jump Starter's LED light to illuminate an engine bay, demonstrating its utility as an emergency light source.

Image: Graphic illustrating the three modes of the LED light: Flashlight, SOS, and Strobe.

Maintenance

• Recharging: For optimal battery life, recharge the jump starter every 3-6 months, even if it has not been used.
• Storage: Store the device in a cool, dry place, away from direct sunlight and extreme temperatures. Use the provided portable storage bag for protection.
• Cleaning: Clean the exterior of the jump starter with a soft, dry cloth. Do not use harsh chemicals or abrasive materials.
• Cable Care: Inspect the jumper cables and clamps regularly for any signs of damage or wear. Replace if necessary.

Troubleshooting

• Vehicle Does Not Start:
  • Ensure the jump starter is fully charged.
  • Check that the smart clip is securely plugged into the jump starter.
  • Verify that the red and black clamps are correctly and firmly attached to the car battery terminals (red to positive, black to negative).
  • If the car battery is extremely low, you may need to use the 'Force Start Function' (consult specific device instructions for activation).
• Jump Starter Does Not Charge:
  • Ensure the USB-C charging cable is properly connected to both the jump starter and the power source.
  • Try a different USB-C cable or power adapter.
  • Verify that the power source is functional.
• LED Light Not Working:
  • Ensure the jump starter has sufficient charge.
  • Press the power button to cycle through the light modes.

User Tips

• Always keep your jump starter charged, especially before long trips or during cold weather, as battery performance can be affected by temperature.
• Familiarize yourself with your vehicle's battery location and terminals before an emergency arises.
• Consider practicing the connection steps once in a non-emergency situation to build confidence.
• The compact size of this jump starter makes it easy to store in your glove compartment or trunk, ensuring it's always available when needed.

Image: A hand holding the YABER Jump Starter, illustrating its compact and lightweight design, which is stated to be 30% smaller than other similar devices.

Warranty and Support

For warranty information or technical support, please refer to the contact details provided by your retailer or visit the official YABER website. Keep your purchase receipt as proof of purchase for any warranty claims.