JIKONG Smart BMS 4.3inch LCD Screen

Contents

JIKONG Smart BMS 4.3-inch LCD Screen Instruction Manual

Model: Smart BMS 4.3inch LCD Screen

Brand: JIKONG

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your JIKONG Smart BMS 4.3-inch TFT LCD Screen. This display unit is designed to provide real-time monitoring of your battery management system (BMS), showing critical parameters such as total voltage, current, State of Charge (SOC), temperature, and individual cell voltages. Please read this manual thoroughly before using the product to ensure proper function and safety.

2. Product Components

The JIKONG 4.3-inch Touch Screen package typically includes the following components:

  • JIKONG 4.3-inch TFT LCD Display Unit
  • Cable A (Long, approx. 3000mm)
  • Cable B (approx. 300mm)
  • Cable C (approx. 280mm)
  • Switch Cable (approx. 120mm)
JIKONG 4.3-inch Touch Screen with various connection cables

Figure 1: JIKONG 4.3-inch Touch Screen and included cables.

3. Setup and Installation

Follow these steps to properly set up your JIKONG Smart BMS display:

  1. Connect Cables: Connect Cable A, B, and C from the display unit to the corresponding ports on your JIKONG Smart BMS. Ensure all connections are secure.
  2. Connect Switch Cable: Attach the Switch Cable to its designated port. This cable is used to power on/off the BMS.
  3. Mount the Display: Securely mount the display unit in your desired location. Consider the dimensions (88.5mm x 135.9mm) for proper fitting.
  4. TF Card (Optional): If firmware upgrades are required, insert a TF card into the TF Card Holder located on the back of the display unit.
Back view of JIKONG 4.3-inch display showing TF Card Holder and dimensions

Figure 2: Rear view of the display unit with TF Card Holder and dimensions.

4. Operating Instructions

4.1 Power On/Off

To power on or off the BMS (and thus the display), perform a long press on the external switch connected via the Switch Cable.

4.2 Display Overview

The 4.3-inch TFT LCD is a touch screen interface that provides comprehensive battery status information. Key indicators include:

  • Battery Pack Total Voltage: Displays the overall voltage of your battery system.
  • Output Current: Shows the current flowing in or out of the battery.
  • SOC (State of Charge): Indicates the remaining battery capacity as a percentage.
  • Temperature: Monitors the battery temperature.
  • Delta Vol: Voltage difference between the highest and lowest cells.
  • Ave Vol: Average cell voltage.
  • Balance Status: Indicates if cell balancing is active (ON/OFF).
  • Charge/Discharge Status: Shows if the battery is currently charging or discharging.
  • Alarm: Displays active warning or error messages.
  • Language: Supports English and Chinese, with customization options.
JIKONG 4.3-inch Touch Screen displaying battery parameters and dimensions

Figure 3: Main display interface with key indicators and dimensions.

4.3 Navigating the Display

The display is touch-sensitive. Tap on different sections or tabs (e.g., STATUS, CELLS VOLTAGE, ALARM) to view more detailed information. For example, selecting 'CELLS VOLTAGE' will show individual battery cell voltages.

Display showing individual battery cell voltages and an over-temperature warning

Figure 4: Individual cell voltage display and an example warning message.

4.4 Alarm Information

When an issue is detected by the BMS, an alarm message will be displayed on the screen (e.g., "S.CHARGE OVER TEMPERATURE PROTECTION"). Address any alarms promptly to prevent damage to your battery system.

5. Maintenance

To ensure the longevity and optimal performance of your JIKONG Smart BMS display, follow these maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the screen and casing. Avoid abrasive cleaners or solvents that could damage the display or finish.
  • Environmental Conditions: Operate the display within recommended temperature and humidity ranges. Avoid exposure to direct sunlight, extreme temperatures, or excessive moisture.
  • Firmware Updates: Periodically check for firmware updates from JIKONG to ensure your display has the latest features and bug fixes. Updates can typically be performed via the TF card slot.

6. Troubleshooting

If you encounter issues with your JIKONG Smart BMS display, refer to the following common problems and solutions:

  • Display Not Turning On:
    • Ensure the Switch Cable is properly connected and a long press is applied.
    • Verify all power connections to the BMS are secure.
  • Incorrect Readings or No Data:
    • Check that Cable A, B, and C are securely connected between the display and the BMS.
    • Confirm the BMS itself is functioning correctly.
  • Alarm Messages Displayed:
    • Identify the specific alarm message (e.g., "OVER TEMPERATURE PROTECTION").
    • Consult your BMS manual for detailed explanations and corrective actions for specific alarms.
  • Touch Screen Unresponsive:
    • Restart the display by powering off and on the BMS.
    • Ensure the screen is clean and free of debris or moisture.

For persistent issues, please contact JIKONG customer support.

7. Specifications

FeatureDescription
Display Type4.3-inch TFT LCD Touch Screen
Dimensions (Display)88.5mm (Height) x 135.9mm (Width)
FunctionsOvercharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection (via connected BMS)
Balance FunctionActive Balanced BMS (via connected BMS)
Charge and Discharge PortCommon Port BMS (via connected BMS)
Charging Current10A (via connected BMS)
Usage ScenarioPower BMS, Energy Storage BMS, 3C Digital BMS
TypeLTO Battery BMS
ConnectivitySupports TF card for firmware upgrade, external switch for BMS control, external buzzer for alarm, external LED indicator for status.
Language SupportEnglish, Chinese (customizable)
Detailed features and specifications of the JIKONG 4.3-inch display and its associated BMS functions

Figure 5: Comprehensive list of product features and specifications.

8. User Tips

  • Always ensure all cables are firmly connected before powering on the system to avoid intermittent readings or connection issues.
  • Regularly check the 'Alarm' section of the display for any warnings that may indicate potential issues with your battery system.
  • Keep the display screen clean to maintain touch sensitivity and readability.

9. Warranty and Support

For any technical assistance, warranty claims, or further inquiries regarding your JIKONG Smart BMS 4.3-inch LCD Screen, please contact JIKONG customer support directly. Keep your purchase records handy when seeking support.

© 2024 JIKONG. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.