RETEVIS RB648Plus

Contents

Retevis RB648Plus Two Way Radio User's Manual

Model: RB648Plus

1. Introduction

This manual provides comprehensive instructions for the safe and efficient operation of your Retevis RB648Plus Two Way Radio. Please read it thoroughly before use to ensure proper handling and to maximize the device's performance and longevity.

Main Features

  • IP67 Waterproof
  • LCD Backlight Display
  • 16 Channels
  • 159 CTCSS/DCS Codes (50 CTCSS, 109 DCS)
  • Channel Busy Lock
  • Earpiece Jack
  • 10 Call Tones
  • VOX (Voice Operated Exchange)
  • High/Low Power Selection
  • Call End Tone
  • One-key Cancel CTCSS/DCS
  • Scan/Priority Channel Scan
  • Keypad Lock
  • Channel Hidden
  • English Voice Broadcast
  • Battery Save
  • Low Battery Alert
  • Local and Remote Alarm
  • TOT (Time-Out Timer)
  • Call Vibration
  • Talk Around
  • Easy Pairing (Pair one channel and Pair all channels)
  • One-key Group Call
  • Double PTT (Push-to-Talk)
  • Allow Transmission Prompt
  • Monitor
  • Scramble
  • Roger Beep
  • Squelch
  • Restore Factory Mode
  • Mic Gain

2. Safety Information

General Warnings

  • Do not charge the radio in flammable, explosive, or radio communication prohibited areas (e.g., gas station, airport).
  • Do not operate the radio without a license in government-prohibited areas.
  • Avoid exposing the radio to direct sunlight and avoid placing it near heating equipment.
  • Avoid placing the radio in dusty, wet, or splashing water environments.
  • If the radio smells or smokes, immediately remove the battery pack and contact the nearest retailer.
  • Technical personnel must repair the radio; self-disassembly is strictly prohibited.

Charging Attentions

  • Use the matched charger to charge the radio.
  • Turn off the radio before charging.
  • For optimal battery performance, charge for at least 5 hours the first time.
  • Avoid prolonged charging to prevent shortening battery life. Stop charging once fully charged.
  • The charger is designed only for this radio. Do not charge other battery packs to avoid damage.
  • Store fully charged batteries in cool, dry areas, away from fire or direct sunlight.
  • Do not turn on the radio during charging.
  • It is normal for the battery pack to be slightly heated during charging.
  • Always obey local regulations when using the radio.

RF Energy Exposure and Product Safety Guide

This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum. Improper use can cause biological damage. Please refer to the following guidelines to control your exposure and ensure compliance with established RF exposure limits.

Unauthorized Modification and Adjustment

Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate this radio. Transmitter adjustments should only be made by or under the supervision of technically qualified personnel.Restriction on Putting into Service

This product may be used in various countries and regions. This radio equipment contains frequency bands subject to licensing procedures. Ensure you have a valid radio license or operator permit before use.

Disposal

The crossed-out wheeled-bin symbol indicates that all electrical and electronic products, batteries, or accumulators must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to local laws and rules.

RF Safety Guidelines

  • Transmit no more than 50% of the time.
  • Reduce the amount of time spent using your wireless device.
  • Use a speakerphone, earpiece, headset, or other hands-free accessory to reduce proximity to the head.
  • Increase the distance between wireless devices and your body.

Hand-held Mode

To control exposure, release the PTT button to receive calls. To transmit, press the Push-to-Talk (PTT) button. Hold the radio vertically with the microphone at least 2.5 centimeters (1 inch) from the nose or lips.

Electromagnetic Interference/Compatibility

Nearly every electronic device is susceptible to electromagnetic interference (EMI). During transmissions, your radio generates RF energy that can cause interference with other devices. Turn off the radio in areas where signs are posted, such as hospitals or healthcare facilities.

  • Persons with pacemakers or other active implantable medical devices should consult their physicians regarding potential risks.
  • Turn the radio OFF immediately if interference is suspected.
  • Do not carry the radio in a chest pocket or near the implantation site.
  • Some digital wireless radios may interfere with hearing aids.
  • If using other personal medical devices, consult the manufacturer to determine if it is adequately shielded from RF energy.

Turn off your radio in the following conditions:

  • Prior to entering any area with a potentially hazardous or explosive atmosphere.
  • When taking on fuel or parked at gasoline service stations.
  • When on board an aircraft.
  • Do not use any radio that has a damaged antenna.
  • Before removing or installing accessories.
  • When the transceiver is used for long transmissions, the radiator and chassis will become hot.

Protect your hearing

  • Use the lowest volume necessary.
  • Limit the amount of time you use headsets or earpieces at high volume.
  • When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear.
  • Excessive sound pressure from earphones and headphones can cause hearing loss.

Batteries Safety

  • WARNING: KEEP NEW OR OLD USED BATTERIES OUT OF REACH OF CHILDREN.
  • In the event of a battery leaking, do not allow the liquid to come into contact with the skin or eyes.
  • Batteries are sensitive to high temperatures; store them in a cool and dry place (+10°C to +25°C).
  • Leaving a battery in an extremely high temperature environment can result in explosion or leakage of flammable liquid or gas.
  • A battery subjected to extremely low air pressure may explode or leak flammable liquid or gas.
  • Turn off your radio before removing or installing a battery.
  • The battery supply terminals are not to be short-circuit.
  • Do not replace the battery in any area labeled "Hazardous Atmosphere".
  • When conductive material touches exposed battery terminals, it can cause burns.
  • Dirty battery contacts should be wiped clean with a dry cloth.
  • Remove batteries from the appliance when not being used for long periods.
  • Exhausted batteries are to be removed from the equipment.
  • Do not dismantle, open or shred batteries.
  • Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in explosion.
  • Rechargeable batteries are only to be charged by adults or by children at least 8 years old under adult supervision.
  • Do not use the charger outdoors or in moist environments.
  • Do not disassemble the charger.
  • WARNING: CHOKING HAZARD - Small Parts. Not suitable for children under 3 years old.

3. Product Overview

Familiar with Radio

Retevis RB648Plus Walkie Talkie with labeled parts

Figure 1: Retevis RB648Plus Walkie Talkie with labeled components.

  1. Antenna
  2. Earpiece jack
  3. Power/Volume knob
  4. LCD display
  5. PTT (Push-to-Talk) button
  6. SOS/Call tone key
  7. Menu/Key lock key
  8. Monitor/Scan key
  9. Speaker
  10. Type-C charging port
  11. Mic port
  12. 【▲】&【▼】 Button

Display Icons

LCD Display showing icons like 2CH, SCAN, HI, VOX, battery indicator, SOS

Figure 2: LCD Display with various icons.

Table 1: Display Icon Instructions
No.IconInstruction
12CHGroup call
2SCANScan
3HIHigh power
4VOXVOX function active
5BatteryBattery indicator
6Transmit
7Receive
8Keypad lock
9CTCSS/DCS codes (00 stands for non CTCSS/DCS)
10Channel number

4. Operating Instructions

Key Instructions

  • 【PTT】 Key: Use double PTT to transmit. One is the small PTT key on the side, and the other is the big PTT key in the front. In menu mode, press the PTT key to save settings and exit the menu.
  • 【▲】 Key: Shortly press to switch options up in the menu. Long press for customized side key functions (OFF, Alarm, Call, Monitor, Group call). Factory default: Monitor.
  • 【▼】 Key: Shortly press to switch options down in the menu. Long press for customized side key functions (OFF, Alarm, Call, Monitor, Group call). Factory default: Group call.
  • 【SOS/CALL】 Key: Shortly press to send Call Tone. Long press for Emergency Alarm.
  • 【MENU】: Shortly press to enter or switch the menu. Long press to lock or unlock.
  • 【Mon/Scan】: Shortly press to turn on or off the scan. Long press to turn on the monitor.

Function Operations

  1. Turn on/off the Radio: Clockwise rotate the power knob to turn on the radio. Anticlockwise rotate the power knob and hear a click sound to turn off the radio. When turning on, the radio will have a power-on prompt and display all icons. After turning on, it will stay in two-way radio mode and display the current channel number, CTCSS/DCS codes, etc.
  2. Volume Adjustment: Clockwise rotate the knob to increase the volume. Anticlockwise rotate the knob to decrease the volume. Note: Do not put the radio speaker too close to the ear when the volume does not adjust to a proper state. Otherwise, a loud voice will hurt the ears.
  3. Transmit & Receive: Press the PTT key and keep the microphone 3-5cm away. Speak in a normal voice. When the radio displays the transmit icon, the radio is transmitting. To avoid stopping your talk, press the PTT key and pause, then start to talk. When finishing talk, release the PTT key to receive. When receiving, the radio displays the receive icon.
  4. Key Lock: Key lock function aims to prevent changing radio settings from accidental operations. Long press the Menu key, hear a beep sound, and the radio displays the icon, the radio enters key lock status. Long press the menu key again, hear two beep sounds, and the radio displays the icon, the radio exits key lock status. Note: In key lock status, pressing any key except the PTT key will send a failure sound.
  5. Menu Setting:
    • Channel Selection: In standby status, press the Menu key once. The current channel number flashes. Press the ▲ or ▼ key to select the wanted channel number. Press the PTT key to save the current setting and exit the menu, or press the Menu key to the next menu setting. The radios can communicate when they are set as the same channel.
    • CTCSS/DCS Codes Selection: CTCSS/DCS codes can reduce interference between radios. The radio has a total of 159 CTCSS/DCS codes (1-50 are CTCSS, 51-159 are DCS). 0 is to turn off CTCSS/DCS codes. In standby status, press the Menu key twice. The current CTCSS/DCS codes setting flashes. Press the ▲ or ▼ key to choose the wanted CTCSS/DCS codes. Press the PTT key to save the current setting and exit the menu, or press the Menu key to the next menu setting. Note: When canceling CTCSS/DCS, the CTCSS/DCS codes display OF.
    • Call Tone Selection: In standby status, press the Menu key three times. The call tone setting displays CA and the call tone number flashes. Press the ▲ or ▼ key to choose the wanted call tone. The speaker will send the corresponding call tone. Press the PTT key to save the current setting and exit the menu, or press the Menu key to the next menu setting. Note: When call tone setting chooses 0, long press the Call key, call function is invalid.
    • VOX/VOX Level Setting: When turning on the VOX function, speak towards the microphone directly. The radio will transmit automatically without pressing the PTT key. In standby status, press the Menu key four times. The VOX appears on the display. Program to set the VOX level (0-9). Press the PTT key to save the current setting and exit the menu.
    • High/Low Power Setting: In standby status, press the Menu key five times. The radio displays Pr. Press the ▲ or ▼ key to choose LO (Low power) or HI (High power). Press the PTT key to save the current setting and exit the menu.
    • Turn on/off Scan Function: In standby status, press the Menu key six times. The radio displays SC. Press the ▲ or ▼ key to choose ON or OFF. ON: Shortly press the Mon/Scan key to turn on the scan. OFF: Shortly press the Mon/Scan key is invalid. The scan can't turn on. Press the PTT key to save the current setting and exit the menu.
    • Turn on/off Roger Beep: In standby status, press the Menu key seven times. The radio displays bE. Press the ▲ or ▼ key to choose ON or OFF. Press the PTT key to save the current setting and exit the menu. After turning on the function, the radio will send the prompt when finishing transmitting.
    • Turn on/off Call Vibration: In standby status, press the Menu key eight times. The radio displays U1. Press the ▲ or ▼ key to choose ON or OFF. Press the PTT key to save the current setting and exit the menu. After turning on the function, the radio vibrates when receiving the first call in the standby status.
    • Turn on/off Talk Around: In standby status, press the Menu key nine times. The radio displays tA. Press the ▲ or ▼ key to choose ON or OFF. Press the PTT key to save the current setting and exit the menu to turn on the function. Note: After turning on the function, the transmitting frequency is the same as the receiving frequency. The radios connect directly without the repeater. When turning it off, the frequencies are different.
  6. Scan Function: In standby status, shortly press the Mon/Scan key. The radio sends a beep sound and enters the scan mode. The channel number increases and the LCD displays SCAN icon. When detecting a signal, the radio will pause on this channel to receive the signal until it disappears. The radio will continue to scan when the signal disappears for 5s. During scanning, press the PTT key, the radio will transmit on the starting scanning channel. When detecting the effective signal, pressing the PTT key, and the radio will transmit on the current channel. Release the PTT key and wait for 5s, the radio will continue to scan. Shortly press the Mon/Scan key, the radio prompts two beep sounds, exits the scan mode, and returns to the standby status.
    • Priority Channel: Set the priority channel through the CPS. CH1-CH16 is optional. When choosing the priority channel, in the scan mode, the radio will scan once priority channel interval a channel.
    • Scan Channel Add/Delete: Set the scan list through the CPS. Set the current channel as Del or Add. When setting as the Add, the current channel enters the scan list. When setting as the Del, the current channel is not in the scan list.
  7. Monitor Function: In the two-way radio mode, long press the Mon/Scan to turn on the function and monitor whether the selected channel has audio transmission or not. If it has no signal, the radio will send a rustle sound. Release the key to turn off the function.
  8. Emergency Alarm: The long press of the SOS/Call key is the alarm. Press the defined alarm key to turn on the emergency alarm.
    • Local Alarm: Set the alarm mode as the local alarm. Press the alarm key, the radio will continuously send the emergency alarm sound. Press the PTT key to exit the alarm.
    • Remote Alarm: Set the alarm mode as the local alarm. Press the alarm key, the radio will continuously send an emergency alarm sound and send an alarm signal to others. When other radios are the same frequency and in receive range, they will send an emergency alarm sound. Press the PTT key to exit the alarm.
  9. One-key Cancel CTCSS/DCS: In the shutdown status, press the ▼ key and turn on the radio. The radio sends a beep sound to turn off all the CTCSS/DCS codes. When it sends two beep sounds, restore all the channel CTCSS/DCS codes.
  10. Battery Save Function: The battery save function saves battery consumption and extends use time. If there are no calls or other operations in 10s, the radio will automatically enter battery save mode. In this mode, the radio still receives information.
  11. Allow Transmission Prompt: Program to turn on the function. Press the PTT key and hear a beep sound, then speak.
  12. Backlight Time: If there are no operations, the backlight will turn off automatically to reduce battery power consumption. Backlight delay time can be set as 5s, 10s, 20s, 30s or 60s.
  13. TOT (Time-Out Timer): When you press the PTT key to communicate over 15-600s, the radio will send a continuous warning sound and stop transmitting automatically.
  14. Companding: Program to turn on the function. It reduces environmental background noise and improves the receiver's voice quality. Note: The radios need to turn on simultaneously.
  15. One-key Group Call: After turning on the group call function, the radio waits for the group call channel in two-way radio mode. Set the group call channel through the CPS. In two-way radio mode, the radio can receive the current channel or the group call channel. When the group call channel is set to OFF, the group call function is turned off. Set the long press function of the 【▲】 or 【▼】 key to group call through the CPS. Press the group call key and the radio will make a call on the group call channel. Set the restore time and PTT reply through the CPS. When the radio receives the signal from the group call channel, directly press the [PTT] key to reply to the group call channel within the restore time.
  16. Easy Pairing:
    • Pair One Channel: Copy the receiving frequency and transmitting frequency on the current channel to the received RF frequency. Set the receiver to the copied channel and turn it off. In shutdown status, press the small [PTT] key on the side and turn on the radio. Wait for 3S and hear three beep sounds, release the [PTT] key and the radio enters pairing mode. Turn on the transmitter and adjust it to the target channel. Press the PTT key to transmit and stay for a while. When the receiver hears a "beep" prompt sound and starts to receive the voice of the transmitter, the channel has been paired successfully and saved automatically. If you need to repeat the operation on other channels, adjust the tester to the next channel and repeat this operation to pair the frequency of each channel one by one. After finishing, restart the radio and talk. Note: When pairing one channel, the receiver enters pairing mode, and the transmitter does not need. Only pair one channel once. The receiver needs to check pair one channel through the CPS to use this function.
    • Pair All Channels: Transmitter: In shutdown status, press the big PTT key on the front and the Call key for 3s, and turn on the radio. The radio sends three beep sounds continuously twice and enters transmitting mode. Receiver: In shutdown status, press the big PTT key on the front and Mon/Scan key for 3s, and turn on the radio. The radio sends three beep sounds continuously twice and enters receiving mode. Press the PTT key of the transmitter and the LED indicator lights up red, the radio transmits data. Restart the radio to exit the mode. The LED indicator of the receiver turns purple to blue, the radio receives the data. After receiving the data, the radio will turn on automatically.
  17. Channel Hidden: If customers only want to communicate on Channel 1, they can hide other channels through the CPS.
  18. Scramble: Turn on the scramble through the CPS, and set the scramble code 1-8 of each channel.
  19. Restore Factory Setting: In shutdown status, press the PTT key on the side and ▼ key, and turn on the radio. The radio will prompt two beep sounds. Release the keys and restart the radio to restore factory setting.

5. Specifications

Specification table for Retevis RB648Plus

Figure 3: Detailed technical specifications of the Retevis RB648Plus.

Table 2: General Specifications
CategorySpecification
Frequency Range400-480MHz
Memory Channel16
Bandwidth25kHz/12.5kHz
Work VoltageDC 7.4V
Battery2000mAh Built-in Li-ion
Work Temperature-20°C ~ +60°C
Antenna Impedance50Ω
Dimensions206x61x33mm (Antenna included)
Table 3: Transmitter Specifications
CategorySpecification
RF PowerHigh power: 5W; Low power: 0.5W
Frequency Stability±2.5ppm
Adjacent Power≤60dBm@12.5KHz
Modulation MethodFM
Transmit Current≤1700mA
Table 4: Receiver Specifications
CategorySpecification
Receive Sensitivity≤-119dBm(12dBSINDA)
Audio Power> 1W
Audio Distortion≤3%
Receive Current≤410mA

Factory Frequency (RB648Plus UHF)

Table 5: Factory Frequency Settings
Channel NO.RX FrequencyTX FrequencyMax Power OutputCTCSS/DCS
1461.11250461.112505W67.0
2461.13750461.137505W67.0
3461.16250461.162505W67.0
4468.56250468.562505W67.0
5468.61250468.612505W71.9
6468.66250468.662505W71.9
7456.33750456.337505W71.9
8456.43750456.437505W71.9
9459.60625459.606255W94.8
10448.19375448.193755W94.8
11469.36875469.368755W94.8
12449.31250449.312505W94.8
13459.12500459.125005W136.5
14444.55000444.550005W136.5
15457.17500457.175005W136.5
16442.87500442.875005W136.5

CTCSS Chart (Hz)

Table 6: CTCSS Frequencies
NumberFrequencyNumberFrequencyNumberFrequencyNumberFrequencyNumberFrequency
167.0269.3371.9474.4577
679.7782.5885.4988.51091.5
1194.81297.413100.014103.515107.2
16110.917114.818118.819123.020127.3
21131.822136.523141.324146.225151.4
26156.727159.828162.229165.530167.9
31171.332173.833177.334179.935183.5
36186.237189.938192.839196.640199.5
41203.542206.543210.744218.145225.7
46229.147233.648241.849250.350254.1

DCS Code List

Table 7: DCS Codes
NumberDCS-NNumberDCS-NNumberDCS-NNumberDCS-NNumberDCS-N
51D023N52D025N53D026N54D031N55D032N
56D036N57D043N58D047N59D051N60D053N
61D054N62D065N63D071N64D072N65D073N
66D074N67D114N68D155N69D116N70D122N
71D125N72D131N73D132N74D134N75D143N
76D145N77D152N78D155N79D156N80D162N
81D165N82D172N83D174N84D205N85D212N
86D223N87D225N88D226N89D243N90D244N
91D245N92D246N93D251N94D252N95D255N
96D261N97D263N98D265N99D266N100D271N
101D274N102D306N103D311N104D315N105D325N
106D331N107D332N108D343N109D346N110D351N
111D356N112D364N113D365N114D371N115D411N
116D412N117D413N118D423N119D431N120D432N
121D445N122D446N123D452N124D454N125D455N
126D462N127D464N128D465N129D466N130D503N
131D506N132D516N133D523N134D526N135D532N
136D546N137D565N138D606N139D612N140D624N
141D627N142D631N143D632N144D645N145D654N
146D662N147D664N148D703N149D712N150D723N
151D731N152D732N153D734N154D743N155D754N
156D243I157D332I158D731I159D743I

Dimensions and Weight

Diagram showing dimensions (205.55mm x 33mm x 60.5mm) and weight (300g) of the walkie talkie.

Figure 4: Dimensions and weight of the Retevis RB648Plus.

6. Troubleshooting (Fault Emission)

Table 8: Common Issues and Solutions
IssueSolution
Compatible AccessoriesJ9164F/J9109A/C9034A
Which radios can talk toIt can talk to all FM radios, and can talk to all Retevis UHF license radios in factory default setting, such as NR630S.
Can't charge the radio1. The radio features Type-C charging and a desktop charger (two charging methods, if one can't be used, choose the other).
2. If both methods fail, try using the spare Type-C charging cable.
3. If it's not a cable issue, the battery or radio might be abnormal; contact customer service.
Don't press the PTT key, why does the radio transmit automatically?Turn on the VOX function. You can turn off the function on the radios.
Can't turn on the radioMaybe the battery is too low; please charge the radio.

7. User Tips

  • Advantages of RB648Plus: The RB648Plus features higher power for longer communication distance, supports easy pairing, and includes a group call function for efficient team communication across various channels.
  • Compatibility: The RB648Plus can communicate directly with RB648 models by adjusting the RB648 to the same channel and CTCSS/DCS settings.
  • One-Key Pairing: To initiate one-key pairing, press the side PTT key on both radios simultaneously while turning them on. Then, press the PTT key of one radio to transmit. Confirm successful pairing via computer software.
  • Canceling CTCSS/DCS: In shutdown status, press side key 1 and turn on the radio simultaneously to toggle CTCSS/DCS on or off. This enhances compatibility with other two-way radios on the same frequency range.
  • License Requirement: The RB648Plus requires a license for use. Users need to apply for a radio license regulated by the CE to avoid frequency blocking and potential fines.
  • Programming: The radio can be programmed via PC in the 400-480 MHz range. A programming cable is required for this process.
  • Battery Type: The device uses a built-in 2000mAh Li-ion battery. It does not use AA or AAA batteries.

8. Warranty and Support

Warranty Information

  • This guarantee card should be kept by the user; no replacement if lost.
  • Most new products carry a two-year manufacturer's warranty from the date of purchase.
  • For warranty and after-sales service, contact the seller where you purchased the product or refer to products repaired by our local repair center.
  • For warranty service, you will need to provide a receipt or proof of purchase from the actual seller for verification.

Exclusions from Warranty Coverage:

  • Any product damaged by accident.
  • Misuse or abuse of the product, or damage resulting from unauthorized alterations or repairs.
  • If the serial number has been altered, defaced, or removed.

Contact Information

  • Manufacturer: Shenzhen Retevis Technology Co.,Ltd.
  • Address: 7/F, 13-C, Zhonghaixin Science&Technology Park, No.12 Ganli 6th Road, Jihua Street, Longgang District, Shenzhen, China
  • Website: www.retevis.com
  • Email: info@retevis.com
  • Facebook: @retevis.fans
  • European Representative (EC REP): Germany Retevis Technology GmbH, Uetzenäcker 29, 38176 Wendeburg, Germany
  • EC REP Email: Retevis-Europa@outlook.com
  • EC REP Phone: +0049 053029369179

For downloading further resources such as brochures, software/firmware, or other manuals, please contact your direct reseller first or visit retevis.com and check the "support" section for the product link.

© 2024 Retevis. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.