Heltec HXYP-DZS Series

Contents

Heltec 18650 Li-ion Power Wall Battery Holder with BMS User Manual

Model: HXYP-DZS Series

1. Introduction

Thank you for choosing the Heltec 18650 Li-ion Power Wall Battery Holder with BMS. This modular system allows you to build custom battery packs using 18650 cells, providing reliable power with integrated battery management for safety and performance. This manual provides essential information for the safe and efficient setup, operation, and maintenance of your battery holder system.

Heltec 18650 Li-ion Power Wall Battery Holder with BMS components

Figure 1: Heltec 18650 Power Wall Battery Holder System

2. Safety Information

  • Always handle Li-ion batteries with care. Improper handling can lead to fire, explosion, or personal injury.
  • Ensure correct polarity when inserting 18650 cells. Refer to the markings on the circuit board (B+ and B-).
  • Do not short-circuit the battery pack terminals.
  • Use only chargers compatible with Li-ion batteries and the specified voltage for your pack configuration (e.g., 12.6V for 3S, 16.8V for 4S).
  • Avoid physical damage to the battery cells or the holder system.
  • Keep the system away from water, moisture, and extreme temperatures.
  • Ensure proper ventilation when operating the battery pack.
  • If any component appears damaged, do not use the system.

3. Package Contents

Depending on your order configuration, your package may include:

  • BMS (Battery Management System) board (e.g., 3S, 4S, 6S, 7S, 8S, 10S)
  • 18650 Battery Holder boards (e.g., 1P, 2P)
  • Acrylic top and bottom cover boards
  • M3 conductive copper columns (standoffs)
  • Screws and non-slip insulating mats
  • IDC ribbon cables for connecting multiple layers (length varies based on stack height)
M3 conductive copper columnsIDC ribbon cables for stacking

Figure 2: Included hardware (copper columns, ribbon cables)

4. Setup & Assembly

4.1. Battery Installation

  1. Ensure all 18650 batteries are of the same type, capacity, and charge level for optimal performance.
  2. Carefully insert each 18650 battery into the holder slots, observing the polarity markings (B+ and B-) on the circuit board. Incorrect polarity can damage the batteries and the BMS.
Battery installation orientation

Figure 3: Correct battery installation orientation

4.2. Stacking Multiple Layers (if applicable)

If you have multiple battery holder boards (e.g., 1P, 2P) to create a larger pack (e.g., 6S2P, 7S2P), follow these steps:

  1. Align the battery holder boards vertically.
  2. Use the provided M3 conductive copper columns to connect and secure the layers.
  3. Connect adjacent layers using the appropriate IDC ribbon cables. Ensure the connectors are fully seated.
6S Assembly Diagram

Figure 4: Example 6S Assembly Diagram

7S Assembly Diagram

Figure 5: Example 7S Assembly Diagram

4.3. Connecting BMS and Enclosure

  1. Place the BMS board on top of the assembled battery holder stack.
  2. Connect the balance leads from the battery holder stack to the corresponding ports on the BMS board.
  3. Secure the acrylic top and bottom cover boards using the remaining screws and non-slip insulating mats.
Non-slip insulating mat installation

Figure 6: Non-slip insulating mat for stability and safety

4.4. Wiring Input/Output and Charging

  • Output Terminals (P+, P-): The BMS board features XT60 output connectors and 4PIN terminals for positive and negative poles. Connect your load to these terminals, ensuring correct polarity.
  • Charging Port: The system includes a DC5.5 * 2.1mm charging port. Connect your compatible Li-ion charger to this port.
P+ P- input/output terminal

Figure 7: P+ P- Output Terminals (XT60 and 4PIN)

DC5.5 * 2.1mm charging port

Figure 8: DC5.5 * 2.1mm Charging Port

5. Operating Instructions

5.1. Initial Activation

After the first assembly and connection, the BMS may be in a low-power state. To activate the output, connect a suitable charger to the charging port and charge for a few seconds. This will initiate the BMS and enable output.

5.2. Voltage Considerations

If you encounter issues with charging or output after assembly, measure the voltage of each battery section separately. If there is a significant voltage difference between cells or if any combination exceeds 4.0V, the BMS might not activate. In such cases, adjust the voltage of the higher cells to around 3.7V before combining them.

6. Maintenance

  • Regularly inspect the battery pack for any signs of damage, loose connections, or corrosion.
  • Keep the system clean and free from dust and debris.
  • Store the battery pack in a cool, dry place when not in use, ideally at a partial charge (around 50%).
  • Avoid fully discharging the battery pack for extended periods, as this can reduce battery life.

7. Troubleshooting

7.1. No Output or Charging Issues

  1. Check Connections: Carefully review all wiring and connections for errors, especially polarity.
  2. Activate BMS: Ensure the BMS has been activated by connecting a suitable charger for a few seconds after initial assembly.
  3. Cell Voltage Balance: Measure individual cell voltages. If there's a significant imbalance or cells are over 4.0V, balance them to around 3.7V.
  4. BMS Fault: In rare cases, a BMS component (e.g., diode) might be defective. If all other steps fail, contact support.

7.2. Overheating

If the battery pack or BMS becomes excessively hot during operation or charging, immediately disconnect the load/charger and investigate the cause. This could indicate a short circuit, overcurrent, or internal cell issue.

8. Specifications

FeatureSpecification
BrandHeltec
Accessory TypeBattery Accessories
Model Numbers3S, 4S, 6S, 7S, 8S, 10S
PCB IncludedYes
Battery IncludedNo
Charger IncludedNo
ReusabilityReusable
CertificationCE

8.1. BMS Specifics (Example Configurations)

Parameter3S (12.6V)4S (16.8V)6S (25.2V)7S (29V)10S (42V)
Size (mm)110x90110x90150x90150x90130x90
Operating Current30A30A40A40A30A
Transient Current60A60A60A85A60A
Overcharge Range4.225V ± 0.025V
Over-discharge Range2.7V ± 0.5V
Equilibrium Current56mA
Short Circuit ProtectionProtected, delayed self-recovery
7S Product Dimensions

Figure 9: Example Product Dimensions (7S configuration)

9. User Tips

  • Careful Assembly: While assembly is straightforward, be mindful of exposed conductive parts. Ensure all connections are secure and properly insulated to prevent accidental short circuits, especially with screws near battery terminals.
  • Add Protection: Consider adding a full enclosure or additional acrylic protection beyond the top and bottom plates for enhanced safety and durability, especially if the pack will be in an exposed environment.
  • Check Polarity Twice: Always double-check battery polarity and terminal connections (P+, P-) before applying power or connecting a load. Reversed polarity can cause irreversible damage.
  • Modular Design: The system is modular. If you order multiple boards (e.g., 1x BMS + 3x 2P holders), ensure you have the correct length of IDC ribbon cables, standoffs, and screws for your desired stack height.

10. Frequently Asked Questions (FAQ)

Q: Are all necessary cables, standoffs, and screws included for a multi-layer stack?

A: Typically, the necessary hardware (IDC ribbon cables, standoffs, screws) for the ordered configuration (e.g., a 7S package) is included. If you are ordering individual components to build a custom stack, please verify the inclusion of these accessories with your specific order.

Q: Can I create custom configurations like a 7S4P package?

A: Yes, the system is designed to be modular. You can combine multiple 1P or 2P battery holder boards with the appropriate BMS (e.g., a 7S BMS) to achieve custom configurations like 7S4P, provided you have the correct number of holder boards and connection cables.

11. Warranty & Support

For warranty information, technical support, or any inquiries regarding your Heltec product, please contact your original point of purchase or refer to the seller's support channels. Please have your order details and product model number ready when contacting support.

12. Product Video

Video 1: Overview of the Heltec 18650 Power Wall Battery Holder System.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.