1. Introduction
The DEKO DKUS-MIG135M is a versatile 3-in-1 welding machine designed for various welding tasks. It supports Gas/Solid Wire MIG (GMAW), Gasless Flux Core MIG (FCAW), and Stick/MMA welding modes. Featuring IGBT intelligent inverter technology and synergic control, this welder offers improved reliability, efficiency, and ease of use for both hobbyists and professionals. It operates on a standard 110V household current, making it convenient for many workshops.

Figure 1: DEKO 135Amp MIG/MMA Welder
2. Safety Information
Always prioritize safety when operating welding equipment. Failure to follow safety guidelines can result in serious injury or death.
- Eye Protection: Always wear a welding helmet with appropriate shade lenses to protect your eyes from intense light and UV radiation.
- Body Protection: Wear flame-resistant clothing, welding gloves, and safety shoes to protect against sparks, heat, and electric shock.
- Ventilation: Ensure adequate ventilation to remove welding fumes, which can be hazardous to your health. Work in a well-ventilated area or use a fume extractor.
- Electrical Safety:
- Ensure the machine is properly grounded.
- Do not operate in wet conditions or with wet hands.
- Inspect all cables and connections for damage before use.
- The machine is protected from too low or too high supply voltage.
- Fire Prevention: Keep flammable materials away from the welding area. Have a fire extinguisher readily available.
- Overheating Protection: The welding gun has an overheating protector that prevents operation when the machine is overheated. Allow the machine to cool down if this indicator activates.
- Overload/Overcurrent Protection: The machine features automatic shutdown systems for overload and overcurrent conditions to protect the unit and user.
- Children and Bystanders: Keep children and unauthorized personnel away from the welding area.

Figure 2: Welder safety features including overheating, overload, overcurrent, and overvoltage protection.
3. Package Contents
Upon unpacking, please verify that all the following items are included:
- 1 x DEKO 135Amp MMA/MIG Welder (Model: DKUS-MIG135M)
- 1 x 2.5 meter CCA cable with 200A Electrode holder (for MMA/Stick welding)
- 1 x 2.5 meter CCA cable with 200A Earth clamp
- 1 x 2.5 meter Power cable with American standard plug
- 1 x Approximately 2.5 meter fixed MIG torch
- 1 x Slag hammer / Wire brush
- 1 x User Manual (this document)
4. General View and Control Panel

Figure 3: Front and rear view of the welder with labeled components.
- Welding Power Control (Knob)
- Wire Selection (Button)
- MMA-MIG Transfer Switch (Button)
- Digital Display Meter
- Power Indicator Light
- Overheating Indicator Light
- Conversion Interface
- Welding Gun
- Earthing Cable
- Electrode Holder Connector
- Main Switch (ON/OFF)
- Shielding Gas Hose Connector
- Supply Voltage Cable
5. Setup Instructions
5.1 Power Connection
- Ensure the main switch (11) is in the OFF position.
- Connect the supply voltage cable (13) to a standard AC 1-110V power outlet.
5.2 Grounding
- Connect the Earth clamp (9) to a clean, bare metal section of your workpiece or welding table to ensure proper grounding.
5.3 Wire Threading (for MIG/Flux Core)

Figure 4: Wire feeding mechanism and threading diagram.
- Open the wire feeder compartment.
- Place the wire spool onto the spindle (labeled 1 in diagram).
- Thread the filler wire through the guide tube (2), over the wire feeding wheel (3), and under the wire pressing wheel (4).
- Ensure the wire is securely seated in the groove of the wire feeding wheel that matches your wire diameter (0.8mm or 1.0mm).
- Adjust the wire pressing wheel tension (5) to prevent slippage but not crush the wire.
- Feed the wire into the welding gun cable (8) until it emerges from the nozzle.
- Close the wire feeder compartment.
5.4 Gas Connection (for Gas MIG)
- For Gas MIG welding, connect your shielding gas hose to the Shielding Gas Hose Connector (12) at the rear of the machine.
- Ensure all connections are tight to prevent gas leaks.
5.5 Electrode Holder Connection (for MMA/Stick)
- For MMA/Stick welding, connect the electrode holder cable to the Electrode Holder Connector (10).
6. Operating Modes
The DEKO DKUS-MIG135M offers three primary welding modes:

Figure 5: Visual representation of MMA, Flux MIG, and Gas MIG welding modes.
6.1 MMA (Manual Metal Arc) / Stick Welding
- Select MMA mode using the MMA-MIG Transfer Switch (3).
- Insert the appropriate electrode into the electrode holder.
- Adjust the welding power using the Welding Power Control knob (1) according to the electrode type and material thickness.
- The Digital Display Meter (4) will show the current setting.
6.2 Flux MIG (Gasless Flux Core Arc Welding - FCAW)
- Select MIG mode using the MMA-MIG Transfer Switch (3).
- Ensure flux core wire is loaded and threaded correctly (refer to Section 5.3).
- No external shielding gas is required for this mode.
- Adjust welding power with the Welding Power Control knob (1). The synergic control will automatically adjust wire feed speed and current based on your power setting and selected wire diameter.
- Use the Wire Selection button (2) to confirm the wire diameter (0.8mm or 1.0mm).
6.3 Gas MIG (Gas Metal Arc Welding - GMAW)
- Select MIG mode using the MMA-MIG Transfer Switch (3).
- Ensure solid wire is loaded and threaded correctly (refer to Section 5.3).
- Connect the appropriate shielding gas (e.g., Argon, CO2, or Argon/CO2 mix) to the Shielding Gas Hose Connector (12) and ensure the gas flow is set correctly.
- Adjust welding power with the Welding Power Control knob (1). The synergic control will automatically adjust wire feed speed and current based on your power setting and selected wire diameter.
- Use the Wire Selection button (2) to confirm the wire diameter (0.6mm, 0.8mm, 0.9mm, or 1.0mm).
6.4 Synergic Control
The synergic control feature simplifies welding by automatically adjusting the wire feed speed and current in conjunction with the welding power setting. This means that when you adjust the Welding Power Control knob (1) to suit the sheet thickness, the machine will simultaneously optimize both the wire feed speed and the amount of current delivered to the wire. This provides a good starting point for various welding situations, making it easier to achieve consistent welds.

Figure 6: Examples of materials suitable for welding with this machine, including Cast Iron, Mild Steel, Sheet Metal, Stainless Steel, Square Pipe, and Metal Cage.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welder.
- Cleaning: Regularly clean the machine's exterior, especially the cooling vents, to prevent dust and debris buildup. Use compressed air to clear internal components if accessible and safe to do so.
- Cable Inspection: Periodically inspect all welding cables, power cords, and connectors for cuts, fraying, or loose connections. Replace damaged components immediately.
- MIG Torch Maintenance:
- Clean the contact tip and gas nozzle regularly to remove spatter.
- Replace worn contact tips and nozzles as needed.
- Check the liner for blockages or wear and replace if necessary to ensure smooth wire feeding.
- Wire Feeder: Keep the wire feeder mechanism clean and free of debris. Ensure the wire feed rollers are clean and the tension is correctly set.
- Storage: Store the welder in a dry, clean environment, away from excessive dust, moisture, and extreme temperatures.
8. Troubleshooting
If you encounter issues with your welder, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cable disconnected, main switch off, circuit breaker tripped | Check power cable, turn on main switch (11), reset circuit breaker |
| Welder overheats (Overheating Indicator Light (6) on) | Exceeded duty cycle, poor ventilation, blocked cooling vents | Allow machine to cool down, ensure adequate ventilation, clean cooling vents |
| Poor arc starting/unstable arc (MMA) | Incorrect current setting, damp electrodes, poor ground connection | Adjust current, use dry electrodes, ensure good ground connection (9) |
| Wire feeding issues (MIG/Flux Core) | Incorrect wire tension, clogged liner, wrong roller groove, spatter in nozzle | Adjust wire tension, clean/replace liner, ensure correct roller groove, clean nozzle/contact tip |
| No gas flow (Gas MIG) | Gas cylinder empty, regulator off, hose disconnected/kinked | Check gas cylinder, open regulator, check hose connections (12) |
| Welder shuts down unexpectedly | Overload, overcurrent, overvoltage protection activated | Reduce load, check input voltage, allow machine to cool and reset |
9. Specifications

Figure 7: Welder dimensions and technical parameters.
| Parameter | Value |
|---|---|
| Model | DKUS-MIG135M |
| Input Voltage (Vac) | AC 1-110V |
| Frequency (HZ) | 50/60 |
| Input Power (KW) | 4.1 |
| No-Load Voltage (V) | 60 |
| Max. Input Current (A) | 35.2 |
| Rated Duty Cycle | 35% |
| Wire Feeder | Inner |
| Wire Speed (m/min) | 2.5-10 |
| Wire Diameter (mm) | 0.8/1.0 (also supports 0.6mm, 0.9mm for solid wire) |
| Product Dimensions (approx.) | 52cm (L) x 20cm (W) x 31cm (H) |
| Product Weight (approx.) | 8.9 kg |
10. User Tips
- Practice Makes Perfect: If new to welding, practice on scrap metal to get a feel for the machine's settings and arc control before working on important projects.
- Material Preparation: Always ensure your workpiece is clean and free of rust, paint, or grease for the best weld quality.
- Synergic Control Advantage: Leverage the synergic control by starting with the recommended power setting for your material thickness. Fine-tune from there if needed.
- Wire Selection: For Flux Core welding, ensure you are using flux core wire. For Gas MIG, use solid wire with appropriate shielding gas.
- Duty Cycle Awareness: Be mindful of the 35% rated duty cycle. This means the machine can weld for 3.5 minutes out of every 10-minute period at maximum output before needing to cool down. Exceeding this can trigger the overheating protection.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the contact details provided at the point of purchase or on the official DEKO website. Keep your purchase receipt as proof of purchase for any warranty claims.