CMTOOL MMT720

Contents

CMTOOL Fuel Injector Tester Instruction Manual

Model: MMT720

Introduction

The CMTOOL Fuel Injector Tester (Model MMT720) is a versatile diagnostic tool designed for DIY cleaning and testing of automotive fuel injectors. It allows for simultaneous testing of two injectors and offers multiple pulse modes to simulate various engine operating conditions. This manual provides detailed instructions for safe and effective use of the device.

Safety Information

  • Always wear appropriate personal protective equipment, including safety glasses, when working with fuel systems.
  • Perform testing in a well-ventilated area to avoid inhaling fuel vapors.
  • Ensure the vehicle's battery is disconnected before connecting or disconnecting the tester to prevent electrical shorts.
  • Do not smoke or use open flames near fuel or fuel system components.
  • Keep a fire extinguisher nearby.
  • The device operates on 12V DC. Do not connect to higher voltage sources.

Package Contents

Verify that all items are present in your package:

  • 1 x CMTOOL Fuel Injector Tester Unit
  • 1 x Power Connection Cable (with alligator clips for 12V battery)
  • 2 x Injector Connection Cables (with small terminals)
  • Multiple Injector Adapters/Connectors (various sizes, orange)
  • 1 x Storage Case
CMTOOL Fuel Injector Tester kit in a black zippered case, showing the main unit, cables, and orange injector adapters.
Figure 1: Complete CMTOOL Fuel Injector Tester kit, including the main unit, cables, and various orange injector adapters, all neatly stored in a black zippered case.
A set of orange plastic injector adapters of various diameters, including φ12.5, φ9.5, φ11.5, φ10.5, M12, and φ13.5.
Figure 2: Assortment of orange plastic injector adapters with different internal diameters for compatibility with various injector types.

Specifications

FeatureDetail
Model NameMMT720
BrandCMTOOL
Item TypeFuel Injector Tester
Simultaneous TestingTwo Injectors
Adjustable Pulse Modes1-4 Pulse (Short, Medium, Long, Continuous)
External Testing CertificationCE
CertificationCE
Power Source12V DC (Vehicle Battery)
Batteries IncludedNo
High-concerned chemicalNone

Setup

  1. Prepare the Work Area: Ensure you are in a well-ventilated area, away from open flames or ignition sources. Have a fire extinguisher readily available.
  2. Disconnect Vehicle Battery: For safety, disconnect the negative terminal of the vehicle's battery before proceeding.
  3. Connect Power: Connect the red alligator clip of the power connection cable to the positive (+) terminal of a 12V vehicle battery and the black alligator clip to the negative (-) terminal.
  4. Connect Injectors:
    • Select the appropriate orange adapter for your fuel injector(s).
    • Connect the injector connection cables to the fuel injectors. The tester supports two injectors simultaneously.
    • Connect the other end of the injector connection cables to the output terminals on the CMTOOL Fuel Injector Tester unit.
Angled view of the CMTOOL Fuel Injector Tester unit with power and injector cables connected, ready for use.
Figure 3: Angled view of the tester unit with power cables (red and black alligator clips) and injector connection cables attached, demonstrating a typical setup.

Operating Instructions

The CMTOOL Fuel Injector Tester features a simple interface for selecting pulse modes and voltage.

Close-up of the Fuel Injector Tester control panel, showing the digital display, 'Mode', 'Voltage', and 'Start/Stop' buttons, and signal mode indicators.
Figure 4: Close-up of the Fuel Injector Tester control panel, highlighting the digital display for pulse mode, 'Mode', 'Voltage', and 'Start/Stop' buttons, and visual indicators for injector operation.
  1. Power On: Once connected to the 12V battery, the device will power on.
  2. Select Pulse Mode: Press the "Mode" button (labeled 'M') to cycle through the four available pulse modes:
    • 1: Short Pulse - For quick checks of injector functionality.
    • 2: Medium Pulse - Standard testing to observe spray pattern and flow.
    • 3: Long Pulse - Extended testing for more thorough observation.
    • 4: Continuous Pulse - Ideal for prolonged cleaning cycles or detailed observation of spray.
    The selected mode will be indicated on the digital display.
  3. Select Voltage: Press the "Voltage" button to select the desired output voltage for the injectors (5V, 9V, or 12V). Ensure the selected voltage matches the specifications of the injectors being tested to prevent damage.
  4. Start/Stop Test: Press the "Start/Stop" button to begin or end the injector pulse test. When the test is running, the injectors will actuate (click), and fuel (if connected to a cleaning system) will spray.
  5. Observe Spray Pattern: While the test is running, observe the spray pattern of the injectors. A healthy injector should produce a fine, conical mist. Any irregularities, drips, or uneven spray patterns indicate a clogged or faulty injector.
  6. Cleaning (Optional): If using with an injector cleaning solution, follow the instructions for the cleaning solution and run the tester in "Continuous Pulse" mode for a recommended duration to flush out contaminants.

Maintenance

  • Cleaning: After each use, wipe the tester unit and cables with a clean, dry cloth. If exposed to fuel or cleaning solutions, wipe immediately with a damp cloth and then dry thoroughly.
  • Storage: Store the CMTOOL Fuel Injector Tester and its accessories in the provided storage case in a cool, dry place, away from direct sunlight and corrosive chemicals.
  • Cable Inspection: Periodically inspect all cables for signs of wear, cuts, or damage. Replace damaged cables immediately to ensure safe operation.

Troubleshooting

ProblemPossible CauseSolution
Tester does not power on.Incorrect or loose power connection; dead vehicle battery.Ensure alligator clips are securely connected to a charged 12V battery. Check cable integrity.
Injectors do not pulse.Incorrect injector connection; wrong voltage selected; faulty injector.Verify injector cables are correctly attached. Ensure selected voltage matches injector specifications. Test a known good injector if possible to rule out a faulty tester.
Uneven or poor spray pattern.Clogged or dirty injector.Perform an injector cleaning cycle using an appropriate cleaning solution. If the problem persists after cleaning, the injector may need replacement.

User Tips

  • For best cleaning results, use a dedicated injector cleaning fluid and a separate container to catch the sprayed fluid, ensuring proper disposal.
  • When testing, pay close attention to both the spray pattern and any audible clicking from the injector, which indicates it's actuating correctly.
  • Always ensure the injector is securely held or mounted during testing to prevent it from spraying uncontrollably and causing a mess or safety hazard.
  • If testing multiple injectors, label them to keep track of which ones might need further attention or replacement.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase for any warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.