LILYGO T3S3 V1.0

Contents

LILYGO T3S3 V1.0 ESP32-S3 LoRa Development Board User Manual

Model: T3S3 V1.0

1. Introduction

The LILYGO T3S3 V1.0 is a versatile development board designed for IoT applications, integrating the powerful ESP32-S3 main control chip with LoRa communication capabilities. This board is part of the new LoRa series (formerly LoRa32 series) and supports the LoRa 2.4G frequency band, making it suitable for global use. It also features a 0.96-inch OLED display and a TF card slot for expanded storage.

Key Features:

  • Powerful LoRa Communication Performance: Delivers outstanding long-range communication, ideal for IoT applications requiring extended reach and low power consumption.
  • Global Usability with LoRa 2.4G Frequency Band: Ensures stable operation worldwide, complying with various spectrum regulations.
  • Advanced Main Control Chip: Integrated ESP32-S3 provides higher computing performance and additional interface options, enhancing flexibility and expandability.
  • TF Card Support: Allows for extended storage, facilitating data storage and management for applications requiring large-capacity data logging.
  • Wide Range of Applications: Suitable for smart agriculture, smart cities, industrial IoT, and other scenarios leveraging LoRa technology's long-range capabilities.

2. What's in the Box?

Please verify that all items are present and in good condition upon opening the package.

  • 1 x T3S3 V1.0 Development Board
  • 2 x 2.54mm Male PIN Headers (1*13P)
  • 1 x Battery Cable (JST 1.25mm 2P)
  • 1 x LoRa Antenna
Exploded view of LILYGO T3S3 V1.0 components
Figure 1: Exploded view of the T3S3 V1.0 development board and its included components.

3. Specifications

3.1. General Specifications

FeatureDescription
MCUESP32S3FH4R2
Flash4MB
PSRAM2MB
Wireless ConnectivityWi-Fi 802.11, Bluetooth 5.0
Programming PlatformArduino-IDE, Micropython
Onboard FunctionsTF Card Slot, USB or 3.7V Lipo Battery Power Supply, Battery Switch
Onboard ButtonsReset, Boot

3.2. Screen Specifications (0.96-inch OLED)

FeatureDescriptionFeatureDescription
TypeOLEDResolution128 x 64
DriveSSD1306Size0.96-inch Diagonal
InterfaceI2CI2C Interface PinsSDA--IO18, SCL--IO17
Text ColorWhiteBackground ColorBlue

3.3. LoRa Transceiver Specifications

LoRa ModuleSX1280SX1276SX1262
Frequency Bands2.4 GHz868/915MHz868/915MHz
High-efficiency PA+12dB+14dBm+22dBm/+15dBm
Low RX Current9.9mA9.9mA4.6mA

4. Setup Guide

4.1. Component Assembly

  1. Attach LoRa Antenna: Carefully screw the provided LoRa antenna onto the SMA connector on the T3S3 board. Ensure it is finger-tight but do not overtighten.
  2. Connect Power: The board can be powered via the Type-C USB port or a 3.7V Lipo battery connected to the JST 1.25mm 2P connector. If using a battery, ensure the battery switch is in the 'ON' position.
  3. Install TF Card (Optional): Insert a microSD (TF) card into the TF card slot if your application requires external storage.
  4. Attach Pin Headers (Optional): Solder the provided 2.54mm male PIN headers to the board's GPIO pins if you plan to connect external sensors or modules.

4.2. Pinout Diagram

Refer to the following pinout diagram for detailed information on the board's GPIOs and interfaces.

LILYGO T3S3 V1.0 Pinout Diagram
Figure 2: LILYGO T3S3 V1.0 Pinout Diagram, showing GPIO assignments, power connections, and OLED/TF card interfaces.

5. Operation

5.1. Programming the Board

The T3S3 V1.0 board can be programmed using the Arduino-IDE or Micropython. Connect the board to your computer via the Type-C USB port. You will need to install the appropriate board support packages and libraries for ESP32-S3 and LoRa communication in your chosen development environment.

For sample code and detailed programming instructions, please refer to the official LILYGO GitHub repository:

5.2. LoRa Module Power Control (SX1280 PA Module)

⚠️ IMPORTANT WARNING: When using the SX1280 PA module, it is crucial to control the output power of the SX1280 chip between 2-5 dBm to ensure the entire module outputs a power of 20 dBm.

  • If the output power of the SX1280 chip is set higher than 5 dBm, it will exceed the maximum allowable input for the FEM chip and can cause permanent damage to the module.
  • If the output power is lower than 2 dBm, the module's output power will still be within 20 dBm, but may not be optimal.
  • Recommendation: Setting the output power to 3 dBm will ensure an optimal output power of 20 dBm without risking damage.

5.3. Onboard OLED Display

The 0.96-inch OLED display (SSD1306 driver, I2C interface on IO18/IO17) can be used to display sensor data, status information, or debug messages. Libraries for SSD1306 are widely available for both Arduino and Micropython environments.

5.4. Reset and Boot Buttons

  • Reset Button: Press to restart the ESP32-S3 microcontroller.
  • Boot Button: Used in conjunction with the Reset button to enter programming mode (bootloader). Typically, hold down the Boot button, press and release Reset, then release Boot.

6. Maintenance

  • Handle with Care: Avoid dropping the board or subjecting it to excessive force.
  • Static Electricity: Electronic components are sensitive to static discharge. Handle the board on an anti-static mat or by touching a grounded object first.
  • Cleanliness: Keep the board free from dust, dirt, and moisture. Use a soft, dry brush or compressed air for cleaning. Avoid using liquids.
  • Storage: Store the board in a dry, cool environment, preferably in an anti-static bag when not in use.

7. Troubleshooting

  • Board Not Powering On: Ensure the Type-C USB cable is properly connected to a power source or that the Lipo battery is charged and the battery switch is 'ON'.
  • Unable to Upload Code: Verify that the correct board (ESP32-S3 Dev Module) and COM port are selected in your IDE. Ensure the necessary drivers are installed. Try entering bootloader mode manually (hold Boot, press/release Reset, then release Boot).
  • LoRa Communication Issues: Check antenna connection. Verify LoRa module power settings, especially for SX1280 (refer to Section 5.2). Ensure frequency bands match between communicating devices.
  • OLED Display Not Working: Check I2C connections (IO18/IO17). Ensure the correct SSD1306 library is installed and initialized in your code.
  • Module Damage after LoRa Use: If using the SX1280 PA module, re-check your code for the SX1280 chip's output power setting. Values above 5 dBm can damage the FEM chip.

8. User Tips

  • Optimize LoRa Range: For maximum LoRa communication range, ensure your antenna is properly connected and positioned. Experiment with different LoRa spreading factors and bandwidths to find the optimal settings for your environment.
  • Power Management: When running on battery, optimize your code for low power consumption by utilizing ESP32-S3's deep sleep modes and only activating peripherals when necessary.
  • Community Support: LILYGO products often have active communities. Search online forums and groups for project ideas, code examples, and troubleshooting advice from other users.

9. Technical Support

For technical assistance, further documentation, and sample code, please visit the official LILYGO GitHub repository:

For specific inquiries not covered in the documentation, you may contact LILYGO customer service through their official channels.

© 2022 LILYGO. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.