
Figure 1: 2S 20A Lithium Battery Protection Board (BMS)
1. Product Overview
This is a high-quality electronic component module, designed for DIY electronic projects, industrial control equipment, portable devices, and precision electronic products. It features a small size, stable performance, easy installation, and low power consumption. It can realize corresponding functions (power supply, touch control, boost conversion, etc.) efficiently and safely.
For a detailed technical document, please refer to the User Manual (PDF).
2. Safety Warnings
- Professional operation is recommended; avoid touching circuit pins or interfaces during operation to prevent electric shock or module damage.
- Ensure input voltage/current matches the module's rated parameters; do not overload or exceed the maximum rated value.
- Keep away from water, moisture, high temperature, flammable materials, and strong electromagnetic interference sources.
- Do not disassemble, modify, or repair the module without permission; disconnect all power supplies before wiring or maintenance.
- Avoid short circuit of pins or interfaces; reverse connection of positive and negative poles may cause burnout or fire hazard.
- For battery-related modules: Use only compatible battery types (e.g., Li-ion), avoid explosion or leakage.
3. Specifications
| Feature | Value |
|---|---|
| Product Name | 2S 20A Lithium Battery Protection Board |
| Model | Ydh-01 |
| Brand | Liludin |
| Application Scope | Lithium batteries with nominal voltage 3.7V, full charge 4.2V (e.g., 18650, 26650, polymer lithium batteries) |
| Supply Voltage | 7.4V - 8.4V |
| Charging Voltage | 8.4V ~ 9.0V |
| Continuous Discharge Current (Max) | 20A (reduce if heat dissipation is poor) |
| Continuous Charging Current (Max) | 10A |
| Dissipation Power | Standard |
| Operating Temperature | -20°C to +60°C |
| Package Type | DIP |
| Dimensions (Standard Version) | 45mm x 15mm |
| Dimensions (Balance Version) | 48mm x 20mm |

Figure 2: Board Dimensions (Standard and Balance Versions)
4. Installation & Wiring
Professional operation is recommended for safe installation and wiring. Follow these steps carefully:
- Disconnect Power: Always disconnect all power supplies before wiring to avoid electric shock or module damage.
- Connect Components: Connect the power supply, load, or battery to the corresponding pins/interfaces according to the pin definition provided below. Avoid reverse connection.
- Check Wiring: Carefully check all wiring to ensure there are no short circuits, reverse connections, or loose contacts.
- Apply Power: After confirming the wiring is correct, connect the power supply. The module should then operate normally.
4.1. Pin & Interface Definition
| Interface/Pin | Function |
|---|---|
| B- (0V) | Battery pack negative terminal (common negative for output) |
| B1 (4.2V) | Connection point between battery cell 1 positive and battery cell 2 negative |
| B+ (8.4V) | Battery pack positive terminal (common positive for output) |
| P- | Load/Charger negative terminal |
| P+ | Load/Charger positive terminal |
4.2. Wiring Diagram and Important Notes

Figure 3: Typical Wiring Diagram
- Note 1 (Electric Drill Application): To successfully start an electric drill, two 10C-20C power batteries or four 5C-10C power batteries are required. Use copper wires of 2 square millimeters or more for 0V and 8.4V connections (blade connectors are not suitable).
- Note 2 (First-time Welding): When welding the battery for the first time, it is necessary to charge it first before outputting. Connect the wires strictly according to the diagram for 0V, 4.2V, and 8.4V. When welding the wires, do not touch any components on the board and do not intentionally short circuit them.
- Note 3 (Overheating): When welding or charging a battery for the first time, if a single battery exceeds 4.2V with a resistance of "430", it will heat up and discharge (it stops heating when discharged to around 4.19V). If the "430" resistor is severely overheating (too hot to touch), please check if it is connected to the wrong wire.
- Note 4 (Battery Matching): Do not mix good and bad batteries. The capacity and internal resistance between batteries should be as similar as possible.
5. Operating Instructions
- Rated Parameters: Do not exceed the module's rated parameters (voltage, current, power) during use to avoid damage.
- Ventilation: Keep the module in a well-ventilated environment. Slight heating during operation is normal. If the module overheats, disconnect power immediately.
- Application: Use the module according to its intended function (e.g., as a power module for power supply).
- Troubleshooting Restart: If the module stops working, disconnect power first, check wiring and parameters, then restart after troubleshooting.
- Power Disconnection: Always turn off the power before disassembling, maintaining, or replacing the module.
6. Maintenance
To ensure the longevity and optimal performance of your protection board, follow these maintenance guidelines:
- Keep the board clean and free from dust and debris.
- Avoid exposing the module to extreme temperatures, humidity, or corrosive environments.
- Regularly inspect wiring connections for tightness and integrity.
- Ensure adequate ventilation around the module during operation to prevent overheating.
7. Troubleshooting
If you encounter issues with the module, refer to the following common problems and solutions:
- No Function/Output:
- Check the power supply connection.
- Verify all wiring connections are correct and secure.
- Confirm pin definitions and input parameters are correctly applied.
- Unstable Performance:
- Ensure the input voltage is stable.
- Avoid overloading the module.
- Check for poor contact in connections.
- Minimize electromagnetic interference (EMI) sources.
- Module Overheating:
- Reduce the load connected to the module.
- Improve ventilation around the module.
- Check for any short circuits on the board or in the connected system.
- Abnormal Noise/Indicator:
- Keep the module away from potential interference sources.
- Check wiring tightness.
- Inspect the module for any visible damage.
8. User Tips
- This board has been successfully used in applications such as electric drills and audio speakers.
- Consider using this board for modifying radio stations to use lithium-ion batteries.
- Some users have noted that the actual continuous discharge current might be less than the stated 20A under certain conditions. Always verify the board's capacity for your specific load.
- Ensure all connections are solid, especially when dealing with higher currents.
9. Warranty & Support
Warranty Period: 12 months from the date of purchase.
Warranty Coverage: This warranty covers manufacturing defects only. It does not cover man-made damage, damage due to overload, improper use, or operational errors.
Contact Information:
Manufacturer: Shenzhen Yuedonghong Technology Co., Ltd
- Tel: 86-13147003747
- Email: jiaweinuokeji@163.com
- Address: 2C056B, Zhonghang Road Metropolitan Electronic City, Huaqiangbei Street, Futian District, Shenzhen, Guangdong Province, China, Postcode: 518000
EU Authorized Representative (Compliance Responsible Person): APEX CE SPECIALISTS LimItED
- Tel: 353-2066339
- Email: INFO@APEX-CE.COM
- Address: UNIT 3D NORTH POINT HOUSE NORTH POINT BUSINESS PARK NEWMALLOW ROADCORK T23AT2P, IRELAND