1. Introduction
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your 7kW EV Charging Station. Please read this manual thoroughly before using the product and retain it for future reference.
2. Safety Instructions
Always observe the following safety precautions to prevent injury or damage to the product:
- Ensure proper grounding before connecting the charging station to the power supply.
- Do not attempt to open, disassemble, or modify the charging station.
- Keep the charging station and cable away from water, heat, and flammable materials.
- In case of malfunction, immediately press the emergency stop button and disconnect power.
- Only qualified personnel should perform installation and maintenance.
3. Setup and Installation
The charging station is designed for self-contained, wall-mounted installation. It is suitable for both indoor and outdoor use (IP55 rated).
3.1 Mounting the Charging Station
- Choose a suitable location for installation, ensuring it is within reach of your vehicle and a dedicated power supply.
- Mark the drilling points on the wall using the charging station's mounting holes as a template.
- Drill holes and insert appropriate wall anchors (not included).
- Securely mount the charging station to the wall using screws.
3.2 Electrical Connection
WARNING: Electrical installation must be performed by a licensed electrician in accordance with all local and national electrical codes.
- Connect the charging station to a dedicated 220V AC power circuit with a maximum current of 32A.
- Ensure the ground wire is properly connected to prevent electrical hazards.
- Verify all connections are secure before powering on the unit.
4. Operating Instructions
4.1 Charging Your EV
- Ensure the charging station is powered on and the green indicator light is solid (see Section 4.2 for indicator status).
- Take the GBT charging gun and firmly insert it into your vehicle's charging port.
- The charging process will begin automatically, and the indicator light on the station will flash green rapidly.
- To stop charging, ensure the vehicle is unlocked, then press the release button on the charging gun and pull it out from the vehicle's port.
4.2 Indicator Light Status
The charging station features indicator lights to communicate its status:
- Solid Green Light: The charging station is powered on and ready.
- Fast Flashing Green Light: The vehicle is currently charging.
- Slow Flashing Green Light: The vehicle's battery is fully charged.
- Alternating Red and Green Lights: The charging load has been unplugged.
- Red Light Flashing 3 times in 1 second: The ground wire was disconnected before charging.
5. Maintenance
To ensure optimal performance and longevity of your charging station:
- Regularly inspect the charging cable and connector for any signs of wear, damage, or corrosion.
- Keep the charging station clean and free from dust and debris. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
- Ensure the emergency stop button is easily accessible and functioning correctly.
- Periodically check the mounting screws for tightness.
6. Troubleshooting
Refer to the indicator light status (Section 4.2) for initial diagnosis. If the issue persists, contact support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Charging not starting | Ground wire disconnected (Red light flashing 3 times) | Check ground connection; consult electrician. |
| Charging stops unexpectedly | Vehicle unplugged (Alternating Red/Green lights) | Reconnect the charging gun securely. |
| No power to station | Power supply issue, circuit breaker tripped | Check circuit breaker; ensure power supply is active. |
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | EVA007KG/A2 |
| Brand Name | BYD |
| Interface Standard | GBT (GB/T20234.2-2015) |
| Output Current | Max. 32A AC |
| Output Power | 7kW |
| Input Voltage | 220V |
| Frequency | 50/60Hz |
| Protection Level | IP55 |
| Weight | 4.0kg |
| Operating Environment | Indoor or Outdoor |
| Executive Standard | GB/T 18487.1-2015 |
| Production Date | 2023-07-17 |
| Manufacturer | Fudi Power Co., Ltd. |
8. User Tips
- Always verify that your electric vehicle is compatible with the GBT charging standard before attempting to charge.
- For optimal charging speed, ensure your vehicle's charging settings are configured to accept 7kW AC input.
- Consider installing the charging station in a location that is easily accessible but also protected from potential physical damage.
9. Warranty and Support
For warranty information or technical support, please contact your retailer or the manufacturer, Chongqing Baojun Automobile Sales Co., Ltd. Ensure you have your product model number (EVA007KG/A2) and production date (2023-07-17) available when seeking assistance.
