Hikvision POE-CABLE

Contents

Hikvision Ethernet Lan Cable PoE RJ45 Network Cable User Manual

Model: POE-CABLE

This manual provides instructions for the proper installation, operation, and maintenance of your Hikvision Ethernet Lan Cable PoE RJ45 Network Cable.

1. Product Overview

The Hikvision Ethernet Lan Cable is a specialized 10-pin, 10-core cable designed to provide both Power over Ethernet (PoE) and network connectivity for compatible IP cameras, particularly Hikvision models. It features a 10-pin connector for the camera interface, an RJ45 connector for network connection, and a DC power connector for optional power input.

Overview of Hikvision 10-pin PoE network cable
Figure 1: Overview of the 10-pin PoE network cable, showing the 10-pin connector, RJ45, and power connectors. Compatible with IVMS-4200, SADP, and Hik-Connect.

Two main cable variants are available, differing in the length of the multi-wire segment and the main cable:

  • A Cable: Features a 17.5cm multi-wire segment and a 35cm main cable.
  • B Cable: Features a 10cm multi-wire segment and a 38cm main cable.

2. Setup and Installation

  1. Identify Cable Type: Determine if you have the 'A cable' or 'B cable' variant based on the lengths and dimensions provided in the specifications.
  2. Camera Connection: Carefully align the 10-pin connector of the cable with the corresponding port on your POE IP camera. Ensure the pins are correctly oriented and gently push until it is securely seated. Do not force the connection.
  3. Network Connection: Connect the RJ45 end of the cable to your network switch or router that supports Power over Ethernet (PoE). If your network device does not support PoE, you will need to use the DC power connector.
  4. Power Connection (Optional): If not using PoE, connect a compatible DC power adapter (not included) to the DC power connector on the cable. Ensure the power adapter's voltage and current ratings match your camera's requirements.
  5. Secure Cabling: Route the cable neatly and securely, avoiding sharp bends, kinks, or areas where it could be pinched or damaged.
Detailed view of A cable variant with measurements
Figure 2: Detailed view of 'A cable' variant, showing lengths of 17.5cm (multi-wire) and 35cm (main cable), and a main cable diameter of 12.8mm.
Detailed view of B cable variant with measurements
Figure 3: Detailed view of 'B cable' variant, showing lengths of 10cm (multi-wire) and 38cm (main cable), with bundled wire length of 19mm and cable width of 15mm.
Close-up of RJ45 and DC power connectors
Figure 4: Close-up of the RJ45 and DC power connectors.

3. Operating Instructions

Once the cable is securely connected to your IP camera and network/power source, the camera should power on and establish network connectivity. Refer to your IP camera's specific user manual for details on configuring network settings, accessing the camera feed, and utilizing PoE features.

This cable facilitates the transmission of both power and data, simplifying the wiring for your surveillance system.

4. Maintenance

  • Keep the cable clean and free from dust and debris.
  • Avoid exposing the cable to extreme temperatures, direct sunlight for prolonged periods, or harsh chemicals.
  • Regularly inspect the connectors for any signs of wear, corrosion, or damage.
  • Ensure the cable is not under tension or subjected to excessive bending, which can damage internal wires.

5. Troubleshooting

No Power to Camera:

  • Check if the 10-pin connector is fully seated in the camera.
  • Verify that your network switch or injector provides active PoE.
  • If using a DC power adapter, ensure it is correctly connected and providing the correct voltage/current.
  • Test with a different PoE port or power adapter if available.

No Network Connectivity:

  • Ensure the RJ45 connector is securely plugged into the network device.
  • Check the network status lights on both the camera and the network switch/router.
  • Verify that your network settings for the camera are correct (IP address, gateway, etc.).
  • Test the network cable with another device to rule out network issues.

Loose Connection:

  • Gently re-seat all connectors (10-pin, RJ45, DC power).
  • Avoid pulling on the cable itself; always grasp the connector when plugging or unplugging.

6. Specifications

Feature Description
Model Number POE-CABLE
Compatibility POE IP Cameras (specifically Hikvision IP Cameras)
Connectors 10-Pin Camera Interface, RJ45 Ethernet, DC Power Jack
Core Count 10 Core
Cable Type A (Multi-wire segment length) 17.5 cm
Cable Type A (Main cable length) 35 cm
Cable Type A (Main cable diameter) 12.8 mm
Cable Type B (Multi-wire segment length) 10 cm
Cable Type B (Main cable length) 38 cm
Cable Type B (Bundled wire length/width) 19 mm
Cable Type B (Main cable width) 15 mm
Certification CE, FCC
Origin Mainland China

7. Warranty and Support

For warranty information and technical support, please refer to the official Hikvision website or contact your authorized Hikvision dealer. Keep your purchase receipt for warranty claims.

8. User Tips

  • Camera Compatibility: Before purchasing or installing, always verify that this 10-pin cable is compatible with your specific Hikvision IP camera model, especially for newer 'smart hybrid light' cameras, as pin configurations can vary.
  • Cable Management: Use cable ties or clips to manage excess cable length and prevent tangles, which can improve system reliability and aesthetics.
  • Environmental Protection: If installing outdoors, ensure all connections are properly weatherproofed to prevent moisture ingress, even if the cable itself is rated for outdoor use.

9. Manufacturing Process

This video provides a glimpse into the advanced manufacturing processes involved in producing electronic components, ensuring quality and reliability for products like your PoE network cable.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.