Neries Electric Bicycle Brushless Motor Controller & LCD Display

Contents

Neries Electric Bicycle Brushless Motor Controller & LCD Display User Manual

Model: Electric Bicycle Brushless Motor Controller & LCD Display

Brand: Neries

1.0 Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Neries Electric Bicycle Brushless Motor Controller and compatible LCD Display. Please read this manual thoroughly before use to ensure proper functionality and safety.

2.0 Setup and Installation

2.1 Controller Wiring Diagram

Refer to the diagram below for correct wiring connections of the brushless motor controller. Ensure all connections are secure before powering on the system.

Neries Brushless Motor Controller Wiring Diagram
Figure 1: Brushless Motor Controller Wiring Diagram
This diagram illustrates the various connections to the controller, including power, motor, display, and sensors.
  • Coarse black (negative pole) P-/ Rough red (positive electrode) P+: Main power input.
  • Phase line of brushless motor: Connect to the motor's phase wires.
  • Main electric door lock: Connect to the ignition or power switch.
  • Connected to LCD: Connect the display unit.
  • Adjustable linear electronic brake: Connect to the brake levers.
  • Headlamp power supply: For connecting the bicycle's headlight.
  • Intelligent phase recognition: For motor phase detection.
  • Pulse Assist Sensor: Connect to the pedal assist sensor (PAS).
  • Turn the handle: Connect to the throttle.
  • Motor hall sensor: Connect to the motor's Hall sensor wires.
  • Brake power off: Connect to the brake sensor for motor cut-off.

2.2 Parameter Settings (P01-P20)

To access the parameter configuration interface, long-press the 'M' and '+' buttons simultaneously. Use the '+' or '-' buttons to adjust values and the 'M' button to switch between parameters. Long-press 'M' and '+' again to save and exit, or the system will auto-save after 8 seconds of inactivity.

Table 1: Vehicle Parameter Settings
ParameterDescriptionRange/Notes
P01Backlight BrightnessLevel 1 (Dimmest) to Level 3 (Brightest)
P02Odometer Unit0: KM (Kilometers); 1: MI (Miles)
P03Voltage Level24V, 36V, 48V, 60V, 64V. Default: 36V
P04Sleep Timer0 (Disabled); 1-60 (Minutes)
P05Assist Level Mode0 (3-Level Mode); 1 (5-Level Mode)
P06Wheel DiameterUnit: inch. Protocol 2: 5.0~50 (0.1 inch precision). Protocol 5S: 0:16in, 1:18in, 2:20in, 3:22in, 4:24in, 5:26in, 7:28in. This parameter affects speed display accuracy and must be set correctly.
P07Speed Magnet CountRange: 1-100. For standard hub motor, enter actual number of speed magnets. For high-speed (geared) motor, calculate: Number of Speed Magnets x Gear Reduction Ratio.
P08Speed LimitProtocol 2: 0-100 km/h (100 = Unlimited). Protocol 5S: 0-41 km/h. Note: Limit value is based on km; converts accordingly when unit is switched to miles.
P09Start Mode0: Zero-start (power activates from standstill). 1: Non-zero-start (pedaling required to activate motor).
P10Drive Mode0: Pedal Assist only (throttle disabled). 1: Electric drive (throttle only). 2: Pedal assist and electric drive coexist.
P11Assist SensitivityRange 1-24 (Higher = more responsive).
P12Assist Start StrengthRange 1-5 (Higher = stronger initial push).
P13PAS Magnet Type5, 8, or 12 magnets (on pedal assist sensor disk).
P14Controller Current LimitDefault 12A, Range 1-20A.
P15Controller Undervoltage PointConfigurable voltage threshold.
P16ODO ResetPress and hold UP button for 5 seconds.
P17Cruise Control0: Disabled. 1: Enabled.
P18Speed Display CalibrationAdjust range 50% to 150%.
P19Zero-Level Enable0: Includes level 0 (no assist). 1: Excludes level 0 (assist starts from level 1).
P20Protocol Selection0: Protocol 2. 1: Protocol 5S. 2-3: Reserved.

3.0 Operating Instructions

3.1 Button Functions (Quick Start)

Button operations are categorized into short press, long press, and long press of combination keys. Short presses are for quick, frequent operations, while long presses and combination keys are for mode toggling or parameter settings to prevent accidental operation.

Various LCD Displays and Controller
Figure 2: Controller and various LCD Displays
This image shows the main controller unit alongside several compatible LCD display models.
  • Adjust Assist Level:
    - Short Press 'M button icon' (or '+'): Increases assist level by 1.
    - Short Press 'M button icon' (or '-'): Decreases assist level by 1.
  • Switch Speed Display:
    - Long Press 'M button icon' and '+': Switches the speed display.
  • Enable/Disable 6 km/h Cruise Control; Turn Headlight On/Off; Reset Odometer (ODO):
    - While stationary, long press 'M button icon' and '-': Activates 6 km/h Cruise Control. Release to exit.
    - Long press 'M button icon' (or '+'): Turns the headlight on/off.
    - While in the P16 menu, long press 'M button icon' (approx. 5 seconds): Resets the Odometer (ODO).
  • Switch LCD Display On/Off:
    - Long press the 'M' button to turn the display off. If the display is off, long press 'M' to turn it on.
  • Switch Multi-function Display Content:
    - A short press of the 'M' button switches the values in the multi-function display area.

3.2 Display Demonstration

Watch this video for a live demonstration of the LCD display in action, showing speed and other parameters on an electric bicycle.

Video 1: LCD Display in Operation
A demonstration of the LCD display showing real-time speed, battery level, and other riding data on an e-bike.

4.0 Maintenance

Specific maintenance instructions for the controller and display are not provided in this manual. Generally, keep the components clean and dry. Avoid exposing them to extreme temperatures or moisture. Regularly check all wiring connections for tightness and signs of wear.

5.0 Troubleshooting

If you encounter issues with your electric bicycle system, refer to the status codes below. These codes can help identify the source of the problem.

5.1 Vehicle Status Code Definitions

Table 2: General Vehicle Status Codes
Status CodeDefinitionRemark
0Normal Status
1Reserved
2Braking / Brake Engaged
3Pedal Assist Sensor Faultunrealized currently
46 km/h Cruise Control
5Real-time Cruise Control
6Undervoltage Fault / Low Battery Voltage
7Motor Fault
8Throttle Fault / Throttle Grip Fault
9Controller Fault
10Communication Receive Fault
11Communication Send Fault
12BMS Communication Fault
13Headlight Fault

5.2 5S&J-LCD Protocol Vehicle Status Code Definitions

Table 3: 5S&J-LCD Specific Status Codes
Status CodeDefinitionRemark
33Current Anomaly
34Throttle Error
35Motor Phase Loss
36Motor Hall Sensor Fault
37Brake Signal Fault
30Communication Error / Comm Fault

6.0 Specifications

6.1 Ebike Display Specifications

Ebike Display Models SW-900, SW-900YB, SW-900NFC
Figure 3: Ebike Display Models
This image shows the SW-900, SW-900YB, and SW-900NFC display models.
Table 4: Ebike Display Specifications
Ebike DisplaySW-900SW-900YBSW-900NFC
ProtocolUART-2UART-2UART-2
Work Voltage24V/36V/48V/52V/60V24V/36V/48V/52V/60V24V/36V/48V/52V/60V
Display Size3.46" X 2.44"3.46" X 2.44"3.46" X 2.44"
Color Screen✓✓✓

6.2 Controller Specifications

Controller Dimensions and Weight
Figure 4: Controller Dimensions and Weight
This image shows the physical dimensions and weight of the controller unit.
Table 5: Controller Specifications (Various Models)
Controller ModelProtocolWork VoltageController Size (Body)Current LimitPower
QX041KZUART-224V-48V3.5"x 2"x 1.18"13A250/350W
QX041KZUART-236V-60V3.5"x 2"x 1.18"13A250/350W
041ZXBUART-224V-48V3.58"x 2.24"x 1.3"13A250/350W
MSL8-D6UART-236V-60V4"x 2.72"x 1.42"18A350/450W
KZSQ-SX6UART-224V/36V/48V7.28"x 2.17"x 1.22"28A250/350W
KZ-X9-500UART-236V/48V/60V4.29"x 2.17"x 1.18"23A450/500W
KZ-D9-500UART-236V/48V/60V4.72"x 3.31"x 1.73"25A450/500W
SL-098UART-236V-60V7.28"x 3.31"x 1.73"38A1000W
QX074KQ24V-48V3.54"x 2.1"x 1.18"13A250/350W
ZXB-P124V-48V3.58"x 2.24"x 1.3"13A250/350W
QX122KZ48V5.9"x 3.31"x 1.73"28A500W
QX073KQ36V-60V7.17"x 3.31"x 1.73"38A1000W

6.3 Package Dimensions

  • Length: 30 cm
  • Width: 10 cm
  • Height: 8 cm
  • Weight: 0.35 kg

7.0 Warranty and Support

For detailed user guides and documents, a PDF manual is available. You can access it via the following link: User manual (PDF).

For any support inquiries or further assistance, please contact the seller:

8.0 User Tips

  • Product Version Differences: Please note that as product versions are regularly updated, the interface on your device may show slight differences from this guide. However, all main features remain unchanged and fully operational. For any specific problems, you can consult the seller directly.
  • Speed Display Accuracy: Ensure that parameters P06 (Wheel Diameter) and P07 (Speed Magnet Count) are set correctly for accurate speed readings. Incorrect settings will lead to inaccurate speed display.
  • Throttle and Pedal Assist: If your motor is not assisting or responding to the throttle as expected, check parameter P09 (Start Mode) and P10 (Drive Mode) to ensure they are configured for your desired operation (e.g., zero-start vs. non-zero-start, pedal assist only vs. electric drive).
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.