1. Introduction
Thank you for choosing the Xiaomi Mijia Air Pump 2 Pro. This portable electric air compressor is designed for convenient and efficient inflation of various items, including car tires, bicycle tires, motorcycle tires, and sports balls. With its powerful performance, compact design, and intelligent features, it provides a reliable solution for your inflation needs on the go.
2. Safety Information
- Read all instructions carefully before use.
- Keep the device away from children.
- Do not operate the pump in wet conditions or near flammable liquids or gases.
- Avoid prolonged continuous operation to prevent overheating. Allow the device to cool down if it becomes hot.
- Ensure the correct pressure unit (PSI, Bar) is selected for your item to prevent over-inflation.
- Do not point the inflation hose at people or animals.
- Use only the provided charging cable and adapters.
3. Package Contents
Please check the package for the following items:
- Xiaomi Mijia Air Pump 2 Pro
- Inflation Hose
- Presta Valve Adapter
- Needle Valve Adapter (for balls)
- USB-C Charging Cable
- Storage Bag
4. Product Overview
The Xiaomi Mijia Air Pump 2 Pro features a clear digital display and intuitive controls for easy operation. It includes an integrated LED light for illumination in low-light conditions and an emergency red light function.
5. Setup
5.1 Charging the Device
Before first use, fully charge the air pump. Connect the provided USB-C charging cable to the charging port on the device and plug the other end into a compatible 5V=3A USB power adapter (not included). The charging time is approximately 3.5 hours.
5.2 Attaching the Inflation Hose and Nozzle
- Screw the inflation hose securely onto the air pump's outlet port.
- Select the appropriate nozzle adapter for the item you wish to inflate.
- Attach the chosen nozzle adapter to the end of the inflation hose.
6. Operating Instructions
6.1 Powering On/Off
Press and hold the power button to turn the device on or off.
6.2 Selecting Inflation Mode and Pressure Unit
Once powered on, the display will show the current pressure and selected mode. Use the mode button to cycle through different preset inflation modes (e.g., car, bicycle, motorcycle, ball). Use the unit button to switch between PSI and Bar pressure units.
6.3 Setting Target Pressure
Use the '+' and '-' buttons to adjust the target inflation pressure. The device supports an inflation pressure range of 0.2-10.3 bar (3-150 psi).
6.4 Starting Inflation
Connect the nozzle to the item's valve. Press the start/stop button to begin inflation. The pump will automatically stop once the target pressure is reached. The inflation progress will be displayed on the screen.
6.5 Using the LED Lighting
The air pump features an integrated LED light for visibility. Press the light button to turn on the flashlight. Press it again to activate the red emergency flashing light. Press a third time to turn off the light.
7. Maintenance
- Clean the exterior of the pump with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
- Store the pump and its accessories in the provided storage bag in a cool, dry place, away from direct sunlight and extreme temperatures.
- Ensure the inflation hose is detached and stored properly to prevent kinks or damage.
- Regularly check the charging port for dust or debris and clean if necessary.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump does not turn on | Low battery; Device malfunction | Charge the device fully; Contact support if issue persists |
| Pump inflates slowly or not at all | Hose not securely attached; Nozzle blocked; Incorrect mode selected | Ensure hose is tight; Check and clear nozzle; Select correct inflation mode |
| Pump stops unexpectedly | Target pressure reached; Overheating; Low battery | Check pressure reading; Allow to cool down; Recharge battery |
| Inaccurate pressure reading | Loose connection; Sensor issue | Ensure secure connection; Contact support |
9. Specifications
| Feature | Detail |
|---|---|
| Model Number | MJCQB07PQW |
| Inflation Pressure Range | 0.2-10.3 bar / 3-150 psi |
| Working Temperature | -10℃ to 45℃ |
| Rated Input | 5V=3A |
| Rated Capacity | 2500mAh |
| Rated Energy | 27Wh |
| Charging Time | Approximately 3.5 hours |
| Product Size | 152 × 100 × 63mm (bare machine size, without high pressure gas pipe) |
| Working Voltage | 10.8V |
| Charging Interface | USB-C |
| Maximum Pressure | 150PSI |
| Battery Life (approx.) | Inflates ~3.7 empty car tires (205/55 R16 from 0 to 2.5 bar) |
10. User Tips
- For optimal performance, ensure the device is fully charged before extended use.
- Always double-check the recommended pressure for your tires or items before inflation.
- The built-in LED light is very useful for nighttime emergencies or working in dimly lit areas.
- Keep the various nozzle adapters organized in the storage bag for quick access.
11. Warranty and Support
This product comes with a standard manufacturer's warranty. For detailed warranty information, service, or technical support, please refer to the official Xiaomi website or contact your local authorized dealer. Keep your purchase receipt as proof of purchase.