Introduction
This manual provides essential information for the safe and efficient operation of your AIFEN A9E Soldering Station. Please read it thoroughly before initial use and keep it for future reference. The AIFEN A9E is a high-performance soldering station designed for precision welding tasks, compatible with 210, 115, and 245 series soldering iron handles and tips. It features rapid heating, precise temperature control, and memory storage for frequently used settings.
Video: AIFEN A9E Soldering Station in operation, demonstrating tip types and maintenance.
Safety Guidelines
When the power is on, the soldering iron tip temperature can reach 100℃-450℃ (212°F-842°F). Improper use may lead to burns or fire. Please strictly observe the following safety precautions:
- Do not touch the soldering iron tip or any metal parts near it when hot.
- Do not use the soldering iron near flammable materials.
- Inform others in the workspace that the soldering iron tip is hot and can cause dangerous accidents.
- Always turn off the power when resting or after completing work.
- When replacing parts or the soldering iron tip, turn off the power and allow the tip to cool to room temperature.
- This product uses a three-wire grounded plug and must be inserted into a three-hole grounded socket. Do not modify the plug or use ungrounded adapters. If an extension cord is needed, use a grounded three-wire power cord.
- Do not use the soldering iron for any work other than welding.
- Do not tap the soldering iron on the workbench to remove flux residue, as this can severely damage the soldering tips.
- When replacing parts, always use original factory components.
- Do not modify the soldering iron without authorization.
- Do not wet the soldering iron, and do not use it with wet hands.
- Smoke will be emitted during soldering; ensure adequate ventilation in the workspace.
- Do not perform any actions that could harm yourself or damage objects while using the soldering iron.
- This product should be used and stored in places inaccessible to children and under adult supervision, as children may not be aware of the dangers of electrical products.
Product Overview
The AIFEN A9E Soldering Station is designed for precision soldering with quick heat-up and temperature recovery. It supports various handle types and features a user-friendly interface.
Key Features
- High Power: 160W Max Power for rapid heating and stable temperature.
- Fast Heat-up & Recovery: Achieves set temperature in two seconds and recovers in one second.
- Wide Compatibility: Supports 115, 210, and 245 series soldering iron handles and tips.
- Memory Storage: Three memory storage keys (CH1, CH2, CH3) for quick recall of preferred temperature settings.
- Adjustable Standby: Adjustable sleep bracket and standby temperature settings.
- User-Friendly Interface: Digital display with temperature unit display, power progress bar, and intuitive buttons.
Components Diagram

Figure 1: AIFEN A9E Soldering Station with labeled components including HUB, Temperature unit display, Setting Key, Soldering iron tip pull-out box, Actual temperature display, Power progress bar, Save button, Temperature adjustment button, Aluminum bracket, Copper wire cleaning ball, Cleaning sponge, and Handle.
Dimensions

Figure 2: AIFEN A9E Soldering Station dimensions. Host weight: 0.87KG. Dimensions: 120mm (Height) x 135mm (Depth) x 140mm (Width).
Plug Types

Figure 3: Available plug types. 220V EU Plug (suitable for Germany, France, Netherlands, Denmark, Finland, Norway, Poland, Spain, Sweden, Korea, Russian Federation, etc.). 110V US Plug (suitable for United States, Canada, Mexico, Japan, Columbia, etc.). Note: Power and plug are for reference. Please refer to the socket in your home for accuracy.
Product Comparison (A9 Series)

Figure 4: Comparison table for AIFEN A9 series models. The A9E model features 160W peak power, 100°C-450°C temperature range, immediate recovery, power progress display, adjustable bracket, plastic button material, copper wire cleaning brush, multi-function heating core storage, anti-splash, 1M handle line length, and supports 210 tips. Machine size: 140x135x120mm. Finish: Noise.
Setup
Before connecting or disconnecting the handle, ensure the power is turned off to prevent damage to the control circuit board.
- Connect the handle device to the handle socket on the host machine.
- Install the required heating core into the handle.
- Place the soldering station securely and position the handle on its stand.
- Connect the power supply.
- Turn on the power switch. The display window will show "---", indicating the soldering station is in standby mode.
Operating Instructions
Temperature Setting and Storage
- Increasing Temperature: Press the "▲" button once to increase the set temperature by 1°C. The display will show the set temperature. Press and hold "▲" for at least one second to rapidly increase the temperature until the desired temperature is reached, then release.
- Decreasing Temperature: Press the "▼" button once to decrease the set temperature by 1°C. The display will show the set temperature. Press and hold "▼" for at least one second to rapidly decrease the temperature until the desired temperature is reached, then release.
- Storing Settings: After setting the desired temperature, select the channel (CH1, CH2, or CH3) you wish to save to. Press and hold the corresponding channel button (e.g., CH1) to save the current settings to that channel.
- Recalling Settings: To recall saved settings, simply press the desired channel button (CH1, CH2, or CH3) for less than one second.
Temperature Unit Conversion (Celsius/Fahrenheit)
While the station is powered on, briefly press the "SET" button to switch between Celsius (°C) and Fahrenheit (°F) display units.
Key Lock Setting
To enable or disable the key lock, turn off the host, then press and hold the "CH1" button while turning on the power switch. The display will show "☑" for enabled and "☐" for disabled.
Buzzer Setting
To enable or disable the buzzer sound, turn off the host, then press and hold the "CH2" button while turning on the power switch. If enabled, the display will show "♪" and a prompt tone will sound. If disabled, the display will show "X".
Standby Temperature Setting
To enter the standby temperature setting interface, turn off the host, then press and hold the "CH3" button while turning on the power switch. Standby temperature options are 0°C, 150°C, 180°C, 200°C (0°C will turn off standby). After setting, briefly press "CH3" to save and exit.
Temperature Calibration
Every time the heating element is replaced, the temperature must be recalibrated. While the host is powered on, press and hold the "SET" key to enter temperature calibration mode. Use the "▲" or "▼" buttons to adjust the temperature, then press "SET" again to save and exit calibration mode.
Wire-Controlled Handle Operation (A9 Wire-Controlled Version Only)
The following functions are only available on the wire-controlled version of the A9. The standard version does not have these features.
- Handle Temperature Adjustment: In working state, press the temperature adjustment buttons on the handle to increase or decrease the temperature.
- Handle Machine Switch: In working state, press and hold both temperature adjustment buttons on the handle simultaneously to turn the host interface on/off.
Maintenance
Proper maintenance is crucial for extending the lifespan of your soldering station and tips.
Soldering Tip Care
- Temperature Selection: High temperatures can degrade tip function. Always choose the lowest possible temperature for your soldering task. The A9E tips offer excellent temperature recovery, allowing for effective soldering at lower temperatures to protect sensitive components.
- Regular Cleaning: Use a clean, damp sponge or copper wire cleaning ball to clean the tip regularly. After soldering, residual flux, oxides, and carbides can damage the tip, leading to poor soldering or reduced heat conduction. The A9 Pro model includes a cleaning copper brush.
- Cleaning When Not in Use: Do not leave the iron at high temperatures for extended periods when not in use. This can cause solder on the tip to oxidize, significantly reducing its heat conduction.
- After Use: After each use, clean the soldering iron tip and coat it with a fresh layer of solder (tinning) to prevent oxidation.
- Inspection: Do not file the iron tip to remove oxide. Set the temperature to 250°C (482°F). Once stable, clean the tip with a cleaning sponge and inspect its condition. If the tinned part of the tip has black oxide, re-tin it with a new layer of solder, then wipe with a clean sponge until all oxide is removed.
- Tip Replacement: If the soldering iron tip is deformed or heavily rusted, it must be replaced. Soldering tips are consumables and should be replaced as needed.
Heating Core Replacement
This soldering station uses a heating core integrated with the soldering head. After turning off the power and allowing it to cool, simply unplug the old heating core and plug in the new one.
Troubleshooting
This section describes common error messages and their solutions.
- S-E Display & Intermittent Beeping: This indicates that the heating core of the soldering station is burnt out, open-circuited, or not properly inserted into the handle. Ensure the heating core is correctly seated.
- H-A Display & Continuous Beeping: This indicates that the heating core is burnt out and short-circuited. Remove the short-circuited heating core and turn off the host for 3 minutes, then turn it on to recover.
- Initial Use "SE" Error: If "SE" appears during initial use, it is not a quality issue. It means the handle has not detected the soldering tip. Correctly installing the soldering tip will resolve this.
Specifications
| Feature | Specification |
|---|---|
| Brand Name | AIFEN |
| Model Number | A9E |
| Origin | Mainland China |
| Input Voltage | AC100-AC240V 50/60Hz |
| Power | 120W |
| Peak Power | 160W (MAX) |
| Temperature Control Range | 100℃-450℃ (212°F-842°F) |
| Compatible Tips | 210/115/245 series |
| Host Weight | 0.87KG |
| Package Length | 27 cm |
| Package Width | 21 cm |
| Package Height | 17 cm |
| Package Weight | 1.48 kg |
| Certifications | CE, RoHS, WEEE |
User Tips
- Tip Selection: The K-type soldering tip is generally recommended for daily work due to its durability. Fine-point tips are best reserved for very small components or specialized tasks.
- Optimal Temperature: Avoid exceeding 380°C to prevent rapid oxidation and extend tip lifespan. Many users find 300°C sufficient for most tasks.
- Initial Tip Preparation: Upon first use, set the temperature to around 300°C, fully coat the tip with solder, and 'burn' it for five minutes to enhance its longevity.
- Power Cord: Ensure the correct voltage plug (110V US or 220V EU) is used for your region.
- Lightweight Design: The station is remarkably lightweight. When changing tips, you may need to hold the station firmly to prevent it from moving.
- Tip Leakage: Some users have reported concerns about voltage leakage. Ensure proper grounding and check for any unusual behavior.
- Handle Recognition: The station should automatically recognize the handle in use. If you experience issues, ensure the handle and tip are correctly installed.
Warranty and Support
For detailed warranty information and technical support, please refer to the official product documentation. A user manual in PDF format is available for download and further reference. This document contains additional guides and specifications.
Reference: User Manual (PDF)