1. Introduction
The EstarDyn 1.3 inch OLED Display Module is a compact, high-resolution (128x64 pixels) display featuring a SH1106 driver chip and an IIC (I2C) communication interface. Available in white or blue color variants, this module is designed for easy integration with microcontrollers like Arduino, offering clear visuals and low power consumption for various electronics projects.
Figure 1: Overview of the EstarDyn 1.3 inch OLED IIC Display Module, illustrating both white and blue display options and the module's rear view with pinout.
2. Specifications
| Feature | Specification |
|---|---|
| Display Size | 1.3 inches |
| Resolution | 128x64 pixels |
| Driver Chip | SH1106 |
| Communication Interface | IIC (I2C) |
| Supply Voltage | DC 3-5V |
| Operating Modes | 3-wire SPI, 4-wire SPI, IIC (I2C) |
| Power Consumption (Normal Display) | 0.08W |
| Viewing Angle | Greater than 160° |
| Operating Temperature | -30°C to 70°C |
| Module Dimensions (L x W x T) | 35.5mm x 33.5mm x 4.3mm |
| Compatibility | 3.3V and 5V control chip I/O levels |
| Package Type | SMD |
3. Package Contents
Your package should contain the following item:
- 1 x EstarDyn 1.3 inch OLED Display Module (White or Blue variant as ordered)
4. Setup and Wiring
This module primarily uses the IIC (I2C) communication protocol, which requires four connections: VDD, GND, SCK, and SDA. Ensure your microcontroller supports I2C communication.
Figure 2: Front view of the OLED module, highlighting the 4-pin IIC interface.
4.1 Pinout Description
- VDD: Power supply (DC 3-5V)
- GND: Ground
- SCK: Serial Clock (I2C SCL)
- SDA: Serial Data (I2C SDA)
Figure 3: Rear view of the OLED module, showing the version and component layout.
4.2 Wiring to Arduino (Example)
Connect the OLED module to your Arduino board as follows:
- VDD to Arduino 5V (or 3.3V, depending on your Arduino model and power requirements)
- GND to Arduino GND
- SCK to Arduino SCL (Analog Pin A5 on Arduino Uno/Nano, Pin 21 on ESP32, Pin 18 on ESP8266)
- SDA to Arduino SDA (Analog Pin A4 on Arduino Uno/Nano, Pin 22 on ESP32, Pin 19 on ESP8266)
Note: Always double-check your microcontroller's specific I2C pins (SDA and SCL) as they can vary between models.
5. Operation and Programming
To operate the OLED display, you will need to use a compatible library for your chosen microcontroller. For Arduino, popular libraries include:
- Adafruit GFX Library: A core graphics library.
- Adafruit SH1106 Library: Specifically for SH1106-based OLED displays.
- U8g2 Library: A universal graphics library for embedded devices, supporting a wide range of displays including SH1106.
5.1 Basic Steps
- Install Libraries: Use the Arduino IDE's Library Manager to search for and install the necessary libraries (e.g., "Adafruit GFX Library" and "Adafruit SH1106 Library" or "U8g2").
- Include Headers: In your Arduino sketch, include the library headers (e.g.,
#include <Wire.h>,#include <Adafruit_GFX.h>,#include <Adafruit_SH1106.h>). - Initialize Display: Create an instance of the display object, specifying the I2C address (commonly 0x3C or 0x3D) and display dimensions.
- Draw Graphics: Use the library functions to draw text, shapes, bitmaps, etc., to the display buffer.
- Display Content: Call the display function (e.g.,
display.display()) to push the buffer content to the OLED screen.
Figure 4: Examples of the 1.3 inch OLED Display Module in blue and white variants.
6. User Tips
No specific user tips were available from provided data. However, general tips for OLED modules include:
- I2C Address Scan: If the display doesn't work, use an I2C scanner sketch to confirm the correct I2C address (usually 0x3C or 0x3D).
- Power Supply: Ensure a stable 3.3V or 5V power supply. Fluctuations can cause display issues.
- Library Compatibility: Some SH1106 displays might work with SSD1306 libraries, but using a dedicated SH1106 library is recommended for full functionality.
7. Maintenance
- Handling: Handle the module by its edges to avoid touching the display surface or delicate components.
- Cleaning: If necessary, gently clean the display surface with a soft, lint-free cloth. Avoid abrasive materials or harsh chemicals.
- Storage: Store the module in an anti-static bag in a dry environment when not in use to prevent damage from static discharge or moisture.
- Power Off: Always disconnect power before making or changing any wiring connections.
8. Troubleshooting
- Display is blank:
- Check all wiring connections (VDD, GND, SCK, SDA) for proper contact.
- Verify the power supply voltage (3-5V) is correct and stable.
- Confirm the I2C address in your code matches the module's address (typically 0x3C or 0x3D).
- Ensure the correct display library is installed and initialized in your code.
- Garbled text or distorted image:
- Ensure the display resolution (128x64) is correctly set in your library initialization.
- Check for loose connections or interference on the I2C lines.
- Verify that the correct driver chip (SH1106) is specified in your library initialization, if applicable.
- Display works intermittently:
- This could indicate an unstable power supply or loose connections.
- Check for potential electromagnetic interference if the module is near other electronics.
9. Warranty and Support
For technical support, please refer to the seller's contact information or the product page where you purchased this module. Specific warranty details are subject to the terms and conditions provided by the retailer at the time of purchase.