Introduction
Congratulations on your purchase of the ARRMA VENDETTA 3S Brushless 1/8 RC Electric Remote Control Model Car. This high-performance, ready-to-run (RTR) vehicle is designed for thrilling on-road racing experiences. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your new RC car to ensure optimal performance and longevity. Please read this manual thoroughly before operating the vehicle.

The ARRMA VENDETTA 3S Brushless 1/8 RC Electric Remote Control Model Car in blue and green variants.
Safety Warnings
- WARNING: Not suitable for children under 36 months due to small parts.
- Always operate the RC car in open areas, away from people, pets, and obstacles.
- Never operate the vehicle near public roads or in areas with vehicle traffic.
- Keep hands, face, and loose clothing away from moving parts.
- Do not touch the motor or ESC immediately after use, as they can become very hot.
- Always disconnect the battery from the vehicle when not in use.
- Use only recommended batteries and chargers.
Setup
1. Unboxing and Initial Inspection
Carefully remove all components from the packaging. Inspect the vehicle for any signs of damage during transit. Ensure all listed components are present:
- ARRMA VENDETTA RC Car
- Spektrum DX3 DSMR 3 Channel Remote Control
- Operating Instructions (this manual)
Note: Battery and charger are NOT included and must be purchased separately. This model requires a 3S LiPo battery.

Internal chassis layout of the ARRMA Vendetta, highlighting the electronic speed controller (ESC) and motor.
2. Battery Installation
- Ensure the vehicle's power switch is in the OFF position.
- Locate the battery compartment on the chassis.
- Carefully place a fully charged 3S LiPo battery into the compartment.
- Secure the battery using the provided straps or clips to prevent movement during operation.
- Connect the battery to the ESC (Electronic Speed Controller) using the appropriate connector.
3. Remote Control Setup
The Spektrum DX3 DSMR 3 Channel Remote Control operates on a 2.4GHz frequency, providing reliable control. Install 4 AA batteries (not included) into the remote control. Refer to the remote control's specific manual for detailed instructions on battery installation and any necessary binding procedures if the car and remote are not already paired.
Operating Instructions
1. Pre-Run Checks
- Ensure the battery is fully charged and securely installed.
- Check that all wheels are securely attached and can spin freely.
- Verify that the steering and throttle respond correctly to the remote control inputs.
- Inspect for any loose screws or damaged components.
2. Starting the Vehicle
- Turn on the remote control first.
- Then, turn on the power switch on the RC car.
- Wait for the ESC to initialize (you may hear a series of beeps).
3. Basic Controls
- Throttle Trigger: Pull to accelerate forward, push to brake/reverse.
- Steering Wheel: Turn left to steer left, turn right to steer right.
4. Driving Tips
- Start with gentle throttle inputs to get a feel for the vehicle's speed and handling.
- Practice steering in wide-open spaces before attempting tighter turns.
- The VENDETTA is designed for on-road racing; avoid rough terrain to prevent damage.
- Be mindful of battery life and stop operating the vehicle when power significantly drops to avoid over-discharging the LiPo battery.
Action footage showcasing the ARRMA Vendetta RC car's high-speed performance on a track.
Maintenance
1. General Cleaning
- After each run, especially in dusty or dirty conditions, clean the vehicle using a soft brush or compressed air.
- Avoid using water directly on electronic components. If the car gets wet, ensure it is thoroughly dried before storage or next use.
2. Component Inspection
- Wheels and Tires: Check for wear, damage, and ensure wheel nuts are tight.
- Chassis: Inspect for cracks or damage.
- Suspension: Check shocks for leaks and ensure smooth operation.
- Drivetrain: Periodically inspect gears and drive shafts for wear or debris.

Detailed view of the front suspension components.
3. Motor and ESC Care
- Keep the brushless motor free of dirt and debris.
- Ensure the ESC has adequate airflow to prevent overheating.
4. Servo Care
- The metal gear digital servo is robust, but avoid excessive force on the steering linkage.
- Keep the servo area clean from dirt that could impede movement.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Vehicle does not respond to remote control | Low battery in vehicle or remote; Not bound; Power switch off | Charge/replace batteries; Re-bind remote and vehicle (refer to remote manual); Ensure power switches are ON |
| Loss of power or erratic behavior | Low vehicle battery; Overheating ESC/motor; Loose connections | Charge battery; Allow components to cool; Check all electrical connections |
| Steering not working or sluggish | Damaged servo; Obstruction in steering linkage; Low battery | Inspect servo and linkage for damage/debris; Charge battery |
| Vehicle makes unusual noises | Debris in gears; Damaged gears; Loose components | Inspect and clean gears; Replace damaged gears; Tighten loose screws |
Specifications
| Feature | Detail |
|---|---|
| Brand | ARRMA |
| Model | ARA4319V3 VENDETTA |
| Type | RC Electric Remote Control Flat Running Model Car |
| Scale | 1:8 |
| Version | RTR (Ready-to-Run, battery and charger not included) |
| Drive Mode | 4 Wheel Drive (4WD) |
| Power | 3S Brushless |
| Length | 595mm |
| Width | 265mm |
| Height | 158mm |
| Wheelbase | 333mm |
| Weight | 2.9KG |
| ESC | Spektrum Firma 100A Brushless ESC |
| Motor | Brushless Motor |
| Servo | Metal Gear Digital Servo |
| Remote Control | Spektrum DX3 DSMR 3 Channel 2.4GHz |
| Remote Distance | About 200m |
| Material | Metal, Plastic, Rubber |
| Recommended Age | 14+ years |
| State of Assembly | Ready-to-Go |
| Package Includes | Original Box, Operating Instructions, Remote Controller |
User Tips
- Battery Care: Always ensure your LiPo batteries are charged with a compatible LiPo charger and stored safely. Never over-discharge or overcharge them.
- Post-Run Inspection: After each high-speed run, quickly check for any loose screws, especially on the wheels and suspension components. Vibrations can sometimes loosen fasteners.
- Cleanliness: Keep the chassis and moving parts free of dust and small debris. A clean car performs better and lasts longer.
- Smooth Driving: For optimal control and to prevent wear, practice smooth throttle and steering inputs, especially at high speeds.
Warranty and Support
For any warranty claims, technical support, or replacement parts, please contact the original seller or the manufacturer directly. Keep your proof of purchase for warranty validation. Specific warranty terms and conditions may vary by region and retailer.