KKMOON JW-360 Line Finder

Contents

KKMOON JW-360 Wire Tracker User Manual

Model: JW-360 Line Finder

1. Introduction

The KKMOON JW-360 Wire Tracker is a multi-purpose instrument designed for efficient and accurate wire locating and cable testing. It features a developed frequency generator that produces an audible alarm, with increasing loudness as you approach the target line, facilitating quick and precise identification. Beyond basic wire tracking, it offers a range of functionalities including direct current level testing, battery low voltage indication, headphone support for noisy environments, a backlight for dark conditions, open or short circuit testing, volume adjustment, and power-saving features.

This device is ideal for telecommunication bureaus, internet cafes, telecommunication and network engineering companies, electric power departments, and other sectors requiring metal line testing and maintenance. It supports routine maintenance and engineering work for telecommunication networks, computer networks, and other metal conductor lines.

2. Package Contents

Please check the package carefully to ensure all items are present and in good condition:

  • 1 x Emitter Unit
  • 1 x Receiver Unit
  • 1 x RJ11 Cable
  • 1 x RJ45 Cable
  • 1 x Clip Cable (Alligator Clips)
  • 1 x Guideline (User Manual)
JW-360 Wire Tracker components: red emitter and receiver units, RJ11 cable, RJ45 cable, clip cable, and headphones.
Figure 2.1: Included components of the JW-360 Wire Tracker (Red version shown).
JW-360 Wire Tracker components: yellow emitter and receiver units, RJ11 cable, RJ45 cable, clip cable, and headphones.
Figure 2.2: Included components of the JW-360 Wire Tracker (Yellow version shown).

3. Setup

3.1. Battery Installation

Both the Emitter and Receiver units require batteries for operation. Typically, these devices use 9V batteries (not included). To install:

  1. Locate the battery compartment cover on the back of both the Emitter and Receiver units.
  2. Slide or unclip the cover to open the compartment.
  3. Insert a 9V battery, ensuring correct polarity (+/-).
  4. Close the battery compartment cover securely.
Back view of the yellow emitter and receiver units with battery compartments open, showing where to insert batteries.
Figure 3.1: Battery compartment on the back of the units.

3.2. Component Overview

Familiarize yourself with the main components and controls of the JW-360 Wire Tracker:

Diagram of the yellow wire tracker units with labels for components: Hunting light, Line sequence indicator light, Function switch button, Function selector switch, Alignment light, Probe, Signal light, Click button, Headphone jack, LED lighting, Volume adjustment, Lock/lighting switch, RJ11 socket, RJ45 socket.
Figure 3.2: Labeled diagram of the yellow JW-360 Wire Tracker units.
Diagram of the red wire tracker units with labels for components: Hunting light, Line sequence indicator light, Function switch button, Function selector switch, Alignment light, Probe, Signal light, Click button, Headphone jack, LED lighting, Volume adjustment, Lock/lighting switch, RJ11 socket, RJ45 socket.
Figure 3.3: Labeled diagram of the red JW-360 Wire Tracker units.

4. Operating Instructions

4.1. Wire Tracking (Line Finding)

This function helps locate and trace wires within walls, ceilings, or bundles.

  1. Connect the Emitter unit to the cable you wish to trace. Use the appropriate connector (RJ11 for telephone lines, RJ45 for network cables, or the clip cable for other bare wires).
  2. Turn on the Emitter unit and select the 'SCAN' or 'WIRE TRACKER' mode using the function selector switch.
  3. Turn on the Receiver unit.
  4. Move the probe of the Receiver unit along the suspected path of the cable.
  5. Listen for the alarm sound from the Receiver. The sound will become louder as you get closer to the target cable.
  6. Adjust the volume on the Receiver as needed for optimal detection.
  7. In dark environments, activate the LED lighting on the Receiver for better visibility.
A person using the yellow wire tracker, with the emitter connected to a network cable and the receiver being used to trace it.
Figure 4.1: Wire tracking in progress.
A person using the yellow wire tracker, with the emitter connected to a network cable and the receiver being used to trace it, with a bundle of cables in the background.
Figure 4.2: Wire tracking in a complex cabling environment.

4.2. Network Cable Testing (RJ45)

The JW-360 can perform network cable side line sequencing and test for open or short circuits. It is compatible with Category 5, Supercategory 5, SuperCategory 5 shielded, and Category 6 cables up to 1KM in length.

  1. Connect one end of the RJ45 network cable to the RJ45 port on the Emitter unit.
  2. Connect the other end of the RJ45 network cable to the RJ45 port on the Receiver unit.
  3. Turn on both units.
  4. Select the 'TEST' mode on the Emitter unit.
  5. Observe the line sequence indicator lights on both the Emitter and Receiver. The lights will illuminate in sequence (1-8, G) to indicate proper wiring.
  6. Any discrepancies (e.g., lights not illuminating, skipping, or illuminating out of sequence) indicate a wiring fault (open, short, cross, or split pair).
Close-up of the red wire tracker units, showing RJ11/RJ45 ports, headphone jack, and LED light, with an RJ45 cable connected.
Figure 4.3: RJ45 cable connected for testing.

4.3. Telephone Line Testing (RJ11)

Similar to network cable testing, the JW-360 can test RJ11 telephone lines for continuity and faults.

  1. Connect one end of the RJ11 telephone cable to the RJ11 port on the Emitter unit.
  2. Connect the other end of the RJ11 telephone cable to the RJ11 port on the Receiver unit.
  3. Turn on both units.
  4. Select the 'TEST' mode on the Emitter unit.
  5. Observe the line sequence indicator lights for proper wiring and fault detection.
Close-up of the red wire tracker units, showing RJ11/RJ45 ports, headphone jack, and LED light, with an RJ11 cable connected.
Figure 4.4: RJ11 cable connected for testing.

4.4. Other Functions

  • Direct Current Level Test: Use the clip cable to test DC voltage levels on wires.
  • Headphone Function: Plug in headphones (included) into the Receiver unit's headphone jack to minimize external interference in noisy environments.
  • Backlight Function: Activate the backlight on the Receiver unit for operation in low-light or dark conditions.
  • Volume Adjustment: Use the volume control button on the Receiver to adjust the sound level of the alarm.
  • Battery Low Voltage Indication: The device will indicate when batteries are low, prompting replacement.
  • Power Saving: The device is designed with power-saving features to extend battery life.

5. Maintenance

  • Cleaning: Wipe the units with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Battery Replacement: Replace batteries promptly when the low voltage indicator appears to ensure accurate readings and prevent damage from battery leakage. Refer to Section 3.1 for battery installation.
  • Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, remove the batteries.
  • Handling: Avoid dropping the units or subjecting them to strong impacts.

6. Troubleshooting

  • No Signal/Weak Signal during Wire Tracking:
    • Check if both Emitter and Receiver units are powered on.
    • Ensure batteries are not low; replace if necessary.
    • Verify the Emitter is correctly connected to the cable.
    • Adjust the volume on the Receiver to maximum.
    • Ensure the function selector switch on the Emitter is in the correct mode (e.g., 'SCAN').
  • Incorrect Cable Test Results (RJ11/RJ45):
    • Ensure both ends of the cable are securely connected to the Emitter and Receiver ports.
    • Check the cable for visible damage.
    • Verify the function selector switch on the Emitter is in 'TEST' mode.
    • Test with a known good cable to rule out device malfunction.
  • Unit Does Not Power On:
    • Check battery installation and polarity.
    • Replace with fresh batteries.

7. Specifications

Feature Specification
Product Name Line Finder
Model Number JW-360
Brand KKMOON
Material Plastics
Available Colors Yellow, Red
Signal Output Level 8Vp-p
Signal Transmission Distance Up to 1 KM
Emitter Size (L*W*H) 125 * 50 * 25 mm (4.92 * 1.97 * 0.98 in)
Receiver Size (L*W*H) 177 * 40 * 25 mm (6.97 * 1.57 * 0.98 in)
Package Size (L*W*H) 235 * 147 * 45 mm (9.25 * 5.79 * 0.98 in)
Package Weight 165 g (5.82 ounce)
Certification CE
Dimensions of the red emitter and receiver units: Emitter 125x50x25mm, Receiver 177x40x25mm.
Figure 7.1: Dimensions of the JW-360 Wire Tracker units.

8. Warranty and Support

The manufacturer is committed to quality control. If you encounter any product quality issues, you may return the item in its original condition for repair or exchange. In case of product damage during transit, please contact the seller before initiating any dispute or leaving negative feedback. The seller will endeavor to resolve the issue.

For technical support or warranty claims, please contact your point of purchase or the official KKMOON customer service channels.

Warranty information graphic detailing return and repair policy.
Figure 8.1: Warranty and return policy overview.

9. User Tips

  • Use Headphones in Noisy Environments: To avoid external interference and improve accuracy during line tracing, always use the included headphones when working in loud areas.
  • Utilize Backlight: For optimal visibility and ease of use in dimly lit spaces or at night, remember to activate the backlight feature on the Receiver unit.
  • Adjust Volume: Fine-tune the volume on the Receiver to pinpoint the exact location of the wire. A lower volume can help narrow down the search area once you are close to the signal source.
  • Check Batteries Regularly: Ensure both units have sufficient battery power before starting any task to prevent interruptions and ensure reliable performance.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.