intelamp YL002-12A1PK

Contents

Intelamp Solar Security Flood Light

Model: YL002-12A1PK | Brand: intelamp

1. Introduction

Thank you for choosing the Intelamp Solar Security Flood Light. This manual provides essential information for the safe and efficient use of your product. Please read it thoroughly before installation and operation.

Intelamp Solar Security Flood Light with adjustable heads and solar panel
Intelamp Solar Security Flood Light (Model YL002-12A1PK)

2. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture. (Note: This contradicts IP65 rating. The IP65 rating means it is protected against water jets, but not submersion. Avoid direct exposure to strong water streams or prolonged submersion.)
  • Handle with care to avoid cuts or injuries.

⚠️ WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. For disposal, please check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with the applicable legal requirements.

3. Product Features

  • Wide Arc Lighting Area: The solar flood light features 3 adjustable lamp heads, providing a 270° wide angle of illumination.
  • High-Efficiency Solar Panels & High-Capacity Batteries: Equipped with 40 square inch solar panels for efficient charging and a 6000mAh battery, capable of lasting up to 3 nights in sensing mode. Delivers an impressive actual brightness of 1200 lumens.
  • Unique Dual Sensor Design: Two motion sensors offer a full 180 degrees of security coverage, reducing blind spots and enhancing detection range.
  • Durable and Weather-Resistant: IP65 waterproof rating ensures resistance to snow, heat, and wind.
Comparison of Intelamp solar light features: larger solar panel, 6000mAh battery, 1200 lumen brightness
Enhanced features: larger solar panel, higher capacity battery, and increased brightness.
Comparison of 2 motion sensors vs 1 motion sensor detection range
Dual motion sensors provide a wider 180° detection angle compared to single sensor models.
IP65 Waterproof rating for Intelamp solar light
IP65 Waterproof rating ensures durability in various weather conditions.

4. Specifications

AttributeValue
Model NumberYL002-12A1PK
Brand Nameintelamp
Power SourceSOLAR
Voltage5V
Light SourceLED bulbs
Is DimmableYes
Solar Cell TypeLithium battery
Protection LevelIP65
Body MaterialABS
Installation MethodSelf-contained
Is Batteries IncludedYes
Warranty1 year
OriginMainland China
StyleModern Style
UseIndustrial
Package Length26 cm
Package Width15 cm
Package Height13 cm
Package Weight0.915 kg
Dimensions of the Intelamp solar light with solar panel and two sensors
Product dimensions: Solar panel 9.4 in (24.5cm) x 4.3 in (11.5cm), Light unit width 12 in (30.5cm).

5. Setup & Installation

  1. Preparation: Remove all protective films from the solar light casing and solar panel. Ensure the solar panel is unobstructed and free of stains.
  2. Location: Install or place the light fixture in a well-lit, unobstructed location where it can receive direct sunlight for most of the day. The recommended installation height is 1.8-2.5 meters (approximately 6-8 feet).
  3. Mounting: Each package includes screws and tie straps for installation.
    • Screw Fixation: The light can be screwed to hard surfaces such as walls, wooden fences, and garage door frames.
    • Cable Tie Fixation: The light can be bound to trees or posts using the provided tie straps.
  4. Adjustable Angle: Both side light heads and the solar panel can be adjusted to suit your specific lighting needs and optimize sun exposure.
Installation methods for Intelamp solar light: screw fixation and cable tie
Flexible installation options using screws or cable ties.
Adjustable angle of solar panel and light heads
Adjustable solar panel (up to 60°) and light heads (up to 90°) for optimal coverage and charging.

6. Charging

This solar light does not require manual charging. Simply place the light fixture in direct sunlight. The solar panel will automatically absorb sunlight and store electrical energy in the integrated lithium battery.

  • Charging Time: 6-8 hours of sufficient direct sunlight.
  • Lighting Duration: Provides 8-12 hours of nighttime lighting after a full charge. Actual duration depends on weather conditions and sunlight intensity.
Solar light charging for 4 hours and lighting for 24 hours
Efficient solar charging provides extended lighting duration.

7. Operation Modes

Locate the power switch on the side/bottom of the light fixture. Switch it to the "ON" position to turn it on. Some models support a light-controlled mode; switch it to the "Auto" position, and the light fixture will automatically turn on after dark and automatically turn off at dawn.

A short press of the mode button (located on the back of the lamp) cycles through the following lighting modes:

  1. Mode 1 (Dim-to-Bright Sensor Mode): Lights are set on a low brightness setting at all times and will illuminate brightly when motion is detected.
  2. Mode 2 (Off-to-Bright Sensor Mode): Lights will be off and will illuminate brightly when motion is detected.
  3. Mode 3 (Constant Low Light Mode): Lights will be on low light throughout the night, and the motion sensor is inactive.

In sensor modes (Mode 1 & 2), the light automatically turns off after a 30-second delay when no human activity is detected, making it more energy-efficient.

Illustration of Mode 1: Dim light, brightens with motion
Mode 1: Dim light, brightens to 100% with motion, then returns to dim.
Illustration of Mode 2: Off, brightens with motion
Mode 2: Off, brightens to 100% with motion, then turns off.
Illustration of Mode 3: Constant 30% brightness
Mode 3: Constant 30% brightness throughout the night.
Demonstration of the solar light's features, including dual motion sensors and comparison with other models.

8. Maintenance

  • Cleaning: Regularly clean the solar panel surface to remove dust, dirt, and debris. A clean panel ensures optimal sunlight absorption and charging efficiency. Use a soft, damp cloth.
  • Inspection: Periodically check the light fixture for any damage or loose components. Ensure mounting is secure.
  • Battery Care: The integrated lithium battery is designed for long-term use. For optimal performance, ensure the light receives adequate sunlight daily.

9. Troubleshooting

  • Light Not Turning On:
    - Ensure the power switch is in the "ON" or "Auto" position.
    - Verify the solar panel is receiving direct sunlight and is not obstructed.
    - Allow 6-8 hours of charging in direct sunlight before first use or after prolonged storage.
    - Check for any protective films that might still be on the solar panel or light sensors.
  • Dim Light or Short Lighting Duration:
    - The solar panel may not be receiving enough direct sunlight. Relocate the light to a sunnier spot or clear any obstructions.
    - Weather conditions (cloudy days) can affect charging efficiency.
    - Ensure the solar panel is clean.
  • Motion Sensor Not Working Correctly:
    - Ensure the light is in Mode 1 or Mode 2 (sensor modes).
    - Check if the sensor is obstructed by dirt or debris.
    - Verify the installation height is within the recommended 1.8-2.5 meters.
  • Light Stays On Constantly (in sensor mode):
    - This could be due to continuous motion detection in the sensor's range (e.g., moving branches, small animals). Adjust the light's position or angle if possible.
    - If the light is in Mode 3, it is designed to stay on at low brightness.

10. User Tips

  • Optimal Placement: For best performance, ensure the solar panel is angled to receive maximum direct sunlight throughout the day. Adjusting the tilt of the solar panel seasonally can improve charging efficiency.
  • Motion Detection: The dual sensors provide a wide detection range. Position the light to cover the desired area for security and convenience. The light will stay on for approximately 30 seconds after motion is detected.
  • Weather Resistance: While IP65 rated, ensure the light is securely mounted to withstand strong winds and heavy rain.
  • Model Variations: This manual is for model YL002-12A1PK. Other Intelamp models (e.g., YL002-12C, YL002-12B) may feature remote controls or detachable solar panels. This specific model operates via an on-board mode button.

11. Warranty & Support

This product comes with a 1-year warranty from the date of purchase.

For technical support or warranty claims, please contact the manufacturer:

  • Manufacturer: Shenzhen Jindian Electronic Technology Co., Ltd.
  • Email: service@intelamp.com

This product must comply with all applicable safety and regulatory requirements in the market where it is sold. Our company has assessed the requirements and regulations applicable to this product based on its actual product type, function, and target market. The product meets the testing requirements of Shenzhen BCTC.

For a detailed user manual in PDF format, please refer to the official document: User manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.