1. Introduction
This manual provides instructions for the safe and efficient operation of your Six-Pod Rapid Charger, designed for Motorola radios and batteries. Please read this manual thoroughly before using the charger to ensure proper function and to prevent damage.
Compatible Models: PMPN4289, PMPN4283B, PMPN4296, PMPN4290.
2. Package Contents
Verify that all items are present and in good condition:
- Six-Pod Rapid Charger Unit
- AC Power Adapter
- AC Power Cord

3. Setup
- Unpack the Charger: Carefully remove the charger unit, AC power adapter, and AC power cord from the packaging.
- Choose a Location: Place the charger on a flat, stable surface in a well-ventilated area, away from direct sunlight, heat sources, and moisture.
- Connect the Power Adapter:
- Connect the 6-pin connector of the AC power adapter to the power input port on the back of the charger unit.
- Connect the AC power cord to the AC power adapter.
- Plug the AC power cord into a suitable wall outlet.

Figure 3.1: Detail of the 6-pin power connector for the charger. - Power On: Once connected, the charger will power on, and the status indicators will illuminate briefly before entering standby mode.
4. Operating Instructions
The six-pod rapid charger allows for simultaneous charging of up to six radio batteries or radios with batteries attached. Each charging pocket operates independently.

4.1 Charging Procedure
- Ensure the charger is properly connected to power.
- Insert a radio with its battery or a standalone battery into any of the six charging pockets. Ensure the battery contacts align correctly with the charger contacts.
- The charger will automatically detect the battery and begin the charging process.
- Observe the LED indicator for the specific pocket to monitor the charging status.
- Once charging is complete, remove the radio or battery from the pocket.
4.2 LED Indicator Status
The charger features clear LED indicators for each pocket, providing real-time status updates:
| Indicator | Status | Description |
|---|---|---|
| Green (Solid) | CHARGED | Battery is fully charged. |
| Green (Flashing) | > 90% | Battery is over 90% charged. |
| Yellow (Solid) | CHARGING | Battery is currently charging. |
| Yellow (Flashing) | RECONDITIONING / RECALIBRATION | The charger is performing a reconditioning or recalibration cycle. This is normal for some battery types to optimize performance. |
| Red (Solid) | ERROR | Charging error. Refer to the Troubleshooting section. |
| No Light | STANDBY / SERVICE LIFE | No battery inserted, or battery is at the end of its service life (if IMPRES 2 compatible). |
*Note: The "IMPRES 2" indicator and related functions are specific to compatible Motorola IMPRES 2 batteries. Refer to your battery's manual for details on IMPRES 2 features.
5. Maintenance
- Cleaning: Disconnect the charger from power before cleaning. Use a soft, dry cloth to wipe the exterior of the charger. Do not use abrasive cleaners or solvents.
- Contacts: Periodically inspect the charging contacts in each pocket for dirt or debris. Clean gently with a cotton swab if necessary.
- Storage: When not in use for extended periods, store the charger in a cool, dry place.
- Environmental Conditions: Operate the charger within recommended temperature and humidity ranges (typically 0°C to 40°C, 10% to 90% non-condensing humidity).
6. Troubleshooting
If you encounter issues with your charger, refer to the following table:
| Problem | Possible Cause | Solution |
|---|---|---|
| No LED indication when battery inserted. | No power to charger, or battery not properly seated. | Check power connections. Re-insert battery, ensuring proper contact. |
| Red (ERROR) LED is solid. | Battery fault, incorrect battery type, or charger malfunction. | Remove and re-insert the battery. Try a different battery in the same pocket. Try the same battery in a different pocket. If the error persists, the battery may be faulty or incompatible. |
| Battery charges slowly or not fully. | Battery nearing end of life, or environmental conditions. | Ensure charger is in a cool, well-ventilated area. Consider replacing old batteries. |
| Yellow (RECONDITIONING) LED flashes for a long time. | Normal operation for battery optimization. | Allow the cycle to complete. This can take several hours depending on battery condition. |
7. Specifications
| Feature | Detail |
|---|---|
| Product Type | Six-Pod Rapid Charger |
| Brand | Iradio |
| Model Number | PMPN4289 (Compatible with PMPN4283B, PMPN4296, PMPN4290) |
| Item Type | Chargers |
| Dimensions (L x W x H) | Approx. 30 cm x 30 cm x 30 cm (Package dimensions) |
| Weight | Approx. 5.0 kg (Package weight) |
| Power Input | AC (via included power adapter) |
| Charging Pockets | 6 |
8. User Tips
- For optimal battery life, avoid leaving batteries on the charger indefinitely after they are fully charged, especially if they are not IMPRES 2 compatible.
- Always use the original power adapter and cord provided with the charger to ensure compatibility and safety.
- If you notice any unusual heat, smell, or noise from the charger or batteries, immediately disconnect the power and remove the batteries.
9. Warranty and Support
For warranty information or technical support, please contact your point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.