SARIK RMC555

Contents

Universal Gate Remote Control User Manual

Model: RMC555 | Brand: SARIK

1. Introduction

The SARIK RMC555 is a universal gate remote control designed for cloning existing fixed code remotes. It features adjustable frequency and is specifically intended for use with a Remocon RMC888 master copy machine for programming. This manual provides instructions for setting up, operating, and maintaining your RMC555 remote control.

Video 1: RMC555 Product Overview and Internal Components

2. Features

  • Fixed Code Cloning: Designed to easily copy existing fixed code remotes using a Remocon RMC888 duplicator.
  • Adjustable Frequency: Supports a wide range of frequencies from 200 MHz to 500 MHz.
  • Multi-Function Buttons: Four distinct buttons allow for up to 10 different functions through various button combinations.
  • Ergonomic Design: Features a groove design on the front for a better grip.
RMC555 Remote Control side view showing ergonomic groove design

Figure 1: RMC555 Remote Control with ergonomic groove design.

3. Specifications

AttributeValue
Model NumberRMC555
Brand NameSARIK
Encoding MethodFixed code
Adjustable Frequency200 MHz - 500 MHz
Dimensions (L x W x T)50mm x 35mm x 13mm
WeightApproximately 31g
CertificationCE

4. Setup and Programming

The RMC555 remote control is designed to be programmed using a Remocon RMC888 master copy machine. Direct cloning from another remote without the RMC888 is generally not supported or reliable.

4.1. Required Equipment

  • SARIK RMC555 Remote Control
  • Remocon RMC888 Master Copy Machine (not included)
  • Original fixed code remote control to be cloned
  • Small screwdriver (for frequency adjustment and opening the case)
Remocon RMC888 Master Copy Machine

Figure 2: Remocon RMC888 Master Copy Machine (for programming RMC555).

4.2. Internal Components Overview

Before programming, it's important to understand the internal components of the RMC555, specifically the dip switches and the frequency adjustment screw.

Disassembled RMC555 remote showing circuit board and battery

Figure 3: RMC555 Disassembled View.

Close-up of RMC555 circuit board showing dip switches and frequency adjustment screw with ranges 220-275, 275-345, 345-440, 440-560X

Figure 4: RMC555 Circuit Board with Frequency Adjustment and Dip Switches.

4.3. Programming Steps

  1. Open the RMC555 Case: Use a small screwdriver to carefully remove the screw on the back of the remote and open the casing to access the circuit board.
  2. Identify Original Remote's Frequency: Determine the operating frequency of your original remote control.
  3. Adjust RMC555 Frequency: On the RMC555 circuit board (refer to Figure 4), locate the blue adjustment screw. Use a small screwdriver to turn this screw to match the frequency of your original remote. The circuit board indicates frequency ranges such as 220-275, 275-345, 345-440, and 440-560X.
  4. Match Dip Switch Settings: Observe the dip switch settings on your original remote control. Configure the dip switches on the RMC555 circuit board to exactly match those of your original remote.
  5. Use RMC888 Duplicator: Connect the RMC555 to the Remocon RMC888 master copy machine using the appropriate cable connector. Follow the instructions provided with your RMC888 machine to clone the code from your original remote to the RMC555.
  6. Test the Remote: After programming, reassemble the RMC555 case. Test the cloned remote with your gate or garage door opener to ensure it functions correctly.

5. Operating Instructions

Once programmed, the RMC555 operates like your original remote control.

  • Button Functions: The RMC555 has four buttons. Depending on how it was programmed with the RMC888, these buttons can activate up to 10 different functions by pressing individual buttons or combinations.
  • LED Indicator: A small LED light on the remote will illuminate when a button is pressed, indicating signal transmission and battery activity.
Hand holding RMC555 remote control, showing the four buttons

Figure 5: RMC555 Remote Control in hand, highlighting buttons.

6. Maintenance

6.1. Battery Replacement

The RMC555 uses a single AAA battery. If the LED indicator does not light up or the remote's range decreases significantly, it's time to replace the battery.

  1. Open the Case: Remove the screw on the back of the remote (refer to Figure 3) and carefully open the casing.
  2. Remove Old Battery: Gently remove the old AAA battery from its compartment.
  3. Insert New Battery: Insert a new AAA battery, ensuring correct polarity (+/-).
  4. Close the Case: Carefully close the remote's casing and secure it with the screw.

6.2. General Care

  • Keep the remote control dry. Moisture can damage internal circuits.
  • Avoid exposing the remote to extreme temperatures.
  • Do not drop or subject the remote to strong impacts.
  • Clean the remote with a soft, dry cloth. Do not use harsh chemicals.

7. Troubleshooting

ProblemPossible CauseSolution
Remote not working after programmingIncorrect frequency or dip switch settings; low battery.Verify frequency adjustment and dip switch settings against the original remote. Replace battery if necessary. Re-program using the RMC888.
LED does not light up when button is pressedDead or incorrectly inserted battery.Replace the AAA battery, ensuring correct polarity.
Cannot clone from another remote directlyThe RMC555 requires an RMC888 duplicator for reliable cloning.Ensure you are using a Remocon RMC888 master copy machine for programming. Direct cloning is not supported.
Remote range is poorLow battery; interference; incorrect frequency.Replace battery. Ensure no strong interference sources nearby. Recheck frequency setting.

8. User Tips

  • RMC888 is Essential: Many users confirm that programming is only successful when using the dedicated Remocon RMC888 duplicator. Do not expect to clone directly from another remote without it.
  • Check Internal Settings: Always double-check the internal frequency adjustment screw and dip switch settings to ensure they precisely match your original remote.
  • Battery Type: The remote uses a standard AAA battery, which is easy to find and replace.
  • Advanced Use: Some users have noted that the remote's circuit board may have a connection bus, potentially allowing for PC-based programming for advanced users with the right tools and software.

9. Warranty and Support

For any issues, questions, or support regarding your SARIK RMC555 Universal Gate Remote Control, please contact your seller or the manufacturer directly. Keep your purchase receipt for warranty claims, if applicable.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.