1. Introduction
The HITBOX HIM250DPP is an advanced 8-in-1 multifunction welding machine designed for a wide range of welding applications. It supports solid wire MIG (GMAW), cored wire MIG (FCAW), electrode welding (MMA), lift TIG, single pulse MIG, double pulse MIG, and spot welding. This versatile machine is compatible with various wire types and materials, making it suitable for both beginners and experienced professionals in DIY, auto body repairs, home shop work, and farm repairs.
This manual provides essential information for the safe and efficient operation, setup, maintenance, and troubleshooting of your HITBOX HIM250DPP welder. Please read it thoroughly before using the machine.

2. Safety Information
Welding can be dangerous. Always follow safety precautions to prevent injury or damage. This section outlines general safety guidelines. For detailed safety information, refer to relevant industry standards and local regulations.
2.1 General Safety Precautions
- Always wear appropriate personal protective equipment (PPE), including a welding helmet with proper shade, flame-resistant clothing, welding gloves, and safety shoes.
- Ensure adequate ventilation in the work area to avoid inhaling welding fumes.
- Protect bystanders from arc rays and sparks using welding screens or barriers.
- Never weld near flammable materials or in explosive atmospheres.
- Ensure the welding machine is properly grounded.
- Do not touch live electrical parts.
- Disconnect power before performing any maintenance or changing accessories.
- Keep children and unauthorized personnel away from the welding area.
- Use only genuine replacement parts and accessories.

3. Product Overview
3.1 Main Components and Controls

The front panel features a 4.3-inch high-clear LED screen for great visuals in outdoor working environments. It includes a Setting knob, Enter or Exit button, and Parameter Adjusting knob for easy navigation and adjustment. Connection points for the MIG Torch, Negative electrode, and Positive electrode are clearly marked.

3.2 Rear Panel

The rear panel includes the Power Input, a Waterproof Switch, an Air In connection for gas, and a cooling Fan.
3.3 Included Accessories
The following accessories are typically included with your HIM250DPP welder:
- MB24 MIG Torch 9.8 ft
- Welding Clamp 4.9 ft
- Ground Clamp 4.9 ft
- 24KD Graphene Tube 10.5 ft
- Aluminium Wires 1lbs
- Rollers (V:0.030/0.039, U:0.035/0.039)
- Conductive Nozzle x 2
- Pipe Clamp x 2
- Air Hose 6.5 ft
- Wrench
- Hammer
4. Setup Instructions
Proper setup is crucial for safe and effective welding. Follow these steps carefully.
4.1 Wire Feeding Installation
- Open the wire compartment cover.
- Install the wire spool onto the spindle, ensuring it rotates freely.
- Thread the welding wire through the wire feeder mechanism.
- Secure the wire feeder tension arm.

4.2 Cable Connections
The connection method varies depending on the welding process. Refer to the diagram below for correct connections.

4.2.1 Gasless MIG (FCAW) Connection
- Connect the Ground Clamp to the positive (+) terminal.
- Connect the MIG Torch to the negative (-) terminal.
4.2.2 Gas MIG (GMAW) Connection
- Connect the Ground Clamp to the negative (-) terminal.
- Connect the MIG Torch to the positive (+) terminal.
- Connect the gas hose to the 'AIR IN' port on the rear panel and to your gas cylinder.
4.2.3 MMA (Stick) Welding Connection
- Connect the Ground Clamp to the negative (-) terminal.
- Connect the Electrode Holder to the positive (+) terminal.
4.2.4 Lift TIG Welding Connection
- Connect the Ground Clamp to the positive (+) terminal.
- Connect the TIG Torch (not included) to the negative (-) terminal.
- Connect the gas hose to the 'AIR IN' port on the rear panel and to your gas cylinder (if using shielding gas).
4.3 Power Connection
Connect the power cable to a suitable AC220V-240V power supply. Ensure the power switch on the rear panel is in the 'OFF' position before connecting to power.
4.4 Visual Setup Guide
5. Operating Modes and Parameter Adjustment
The HIM250DPP offers an intuitive interface for selecting welding modes and adjusting parameters.

5.1 Mode Selection
Use the 'SET' knob and 'Enter/Exit' button to navigate through the main menu and select your desired welding mode:
- MIG (SYN Gas MIG)
- Single Pulse MIG
- Double Pulse MIG
- Lift TIG (TIG torch not included)
- MMA (Stick Welding)
- Spool Gun MIG (cannot weld aluminum with standard spool gun)
- SYN Gasless MIG (Flux Cored)
- Spot Welding (time adjustable)

5.2 Synergic MIG Welding
In Synergic MIG mode, the machine simplifies setup. After selecting the welding material (e.g., Carbon Steel, Stainless Steel, Aluminum) and wire diameter, the system automatically suggests optimal welding current and wire feed speed. You can then fine-tune parameters using the 'ADJUST' knob.

5.3 Double Pulse MIG Welding for Aluminum
This mode is ideal for aluminum welding, reducing heat exposure and improving weld appearance. Parameters adjustable include:
- Peak Current
- Base Current Percentage (30%-85%)
- Dual Pulse Frequency (0.5Hz-5Hz)
- Dual Pulse Duty Cycle (20%-80%)
5.4 Parameter Adjustment Overview

The display allows for precise adjustment of various parameters depending on the selected mode:
- Wire Diameter: Select the appropriate wire diameter for your material.
- Voltage Trimming: Adjust voltage from -30% to +30%.
- Inductance Adjustment: Adjust inductance from -50% to +50%.
- Spot Welding Time: Adjustable from 0.5s to 10s.
- Intermittent Time: Adjustable from 0.5s to 10s.
- Peak Current: For pulse modes.
- Base Current Percentage: For pulse modes.
- Dual Pulse Frequency: For double pulse MIG.
- Dual Pulse Duty Cycle: For double pulse MIG.
- Hot Start and Arc Force: For MMA mode to prevent sticking.
6. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
6.1 Cleaning
- Periodically clean the exterior of the machine with a dry, soft cloth.
- Use compressed air to blow out dust and debris from the cooling fan and internal components. Ensure the machine is unplugged before doing so.
- Clean the MIG torch liner regularly to prevent wire feeding issues.
6.2 Inspection
- Inspect all cables and connections for damage, fraying, or loose contacts before each use.
- Check the condition of the welding torch, ground clamp, and electrode holder. Replace worn or damaged parts.
- Ensure the wire feeder rollers are clean and free from debris.
6.3 Storage
Store the welder in a clean, dry environment, away from excessive dust, moisture, and extreme temperatures.
7. Troubleshooting
This section provides solutions to common issues you might encounter.
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cable disconnected, power switch off, circuit breaker tripped. | Check power connections, turn on switch, reset breaker. |
| No arc | Poor ground connection, incorrect settings, faulty torch/electrode holder. | Ensure good ground contact, verify welding parameters, inspect torch/holder. |
| Wire feeding issues | Tangled wire, incorrect roller tension, clogged liner, wrong wire diameter. | Untangle wire, adjust roller tension, clean liner, use correct wire. |
| Overheating protection activated | Extended welding time, insufficient cooling. | Allow machine to cool down, ensure proper ventilation, check fan operation. |
| Poor weld quality | Incorrect parameters, improper technique, contaminated material. | Adjust parameters, practice technique, clean workpiece. |
8. Specifications
| Feature | Specification |
|---|---|
| Model Number | HIM250 DPP |
| Brand Name | HITBOX |
| Dimensions | 43 x 24 x 28 cm (17.72 x 7.87 x 13.78 inches) |
| Product Weight | 21.72 LB (approx. 9.85 kg) |
| Package Weight | 17.0 kg (approx. 37.5 lbs) |
| Certification | CE |
| Welding Processes | MIG GAS, Gasless MIG, MMA, Lift TIG, Single Pulse MIG, Double Pulse MIG, Spot Welding, Spool Gun MIG |
| Wire Feeding Speed | Automatic |
| Smart Device | No |
| High-concerned chemical | None |
| Protection Features | VRD, Over-current, Over-voltage, Overload, Overheating Protection |
| Waterproof Rating | IP21 |
| Weldable Materials | Carbon steel, Iron, Galvanised sheet, Stainless steel, Copper, Aluminium, Mild Steel, Cast Iron, Square Pipe, Sheet Metal |


9. User Tips
- Gas Type for MIG: For Gas MIG welding, Argon gas is commonly used, especially for aluminum. For carbon steel, a mix of Argon and CO2 (e.g., Ar98%+CO2 2%) or 100% CO2 is typical. Ensure your gas cylinder and regulator are compatible with the welder's 'AIR IN' connection.
- TIG Torch Compatibility: The Lift TIG function requires a separate TIG torch (WP 17V Lift TIG gun is not included). Ensure any purchased TIG torch is compatible with the welder's connections.
- Aluminum Welding: For optimal aluminum welding, utilize the Double Pulse MIG mode. This mode helps manage heat input, which is critical for aluminum, reducing distortion and improving bead appearance.
- Synergic Settings: Don't hesitate to use the synergic settings as a starting point. They provide a good baseline for various materials and wire diameters, especially for beginners. Fine-tune from there based on your specific application and desired weld quality.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please contact HITBOX customer service or refer to the official HITBOX website. Keep your purchase receipt as proof of purchase for warranty claims.