Introduction
Thank you for choosing a Beitian GPS Module. This manual provides important safety information, usage instructions, and after-sales service information. It applies to the Beitian GPS Module series, including models BE-451, BK-450, and BN-450, which are ultra-low power GNSS receivers designed for various applications.
Safety & Warnings
WARNING
To reduce the risk of injury, fire, electric shock, or property damage, please read and follow all safety information and instructions before using this product.
- This product is intended for users aged 16 years and above.
- Not suitable for children under 3 years. Small parts may present a choking hazard.
- Keep away from fire, high temperature, water, moisture, and corrosive environments.
- Do not disassemble, modify, or repair the product without authorization.
- Use the product only for its intended purpose. Misuse may cause injury or damage.
- If the product (especially electronic parts) is damaged, overheated, emits smoke, unusual odor, or noise, stop using it immediately and contact customer support.
- Keep packaging materials (plastic bags, foam, etc.) away from children to avoid suffocation risk.
- For indoor use only unless otherwise specified on the product or packaging.
Symbols Explanation
| Symbol | Description |
|---|---|
| Warning: Important safety information. | |
| Not suitable for children under 3 years. Choking hazard. | |
| Recommended for users aged 16 and above. | |
| Indoor use only (unless otherwise specified). | |
| Do not dispose of with household waste. Please recycle. | |
| Recyclable packaging. |
Product Overview
The Beitian GPS Module series offers ultra-low power GNSS receivers, ideal for applications requiring precise positioning. The BE-451 is an upgraded version of the BE-450, offering enhanced performance. The modules support multiple global navigation satellite systems (GNSS) including GPS, BDS, Galileo, SBAS, and QZSS. The BK-450 model also supports GLONASS.
Some models, like the BE-450 and BK-450, integrate a compass for improved navigation and orientation capabilities.

Applications
These versatile modules are suitable for a wide range of applications, including:
- Vehicle navigation and tracking
- Drones and UAVs
- Shared bike systems
- Logistics tracking
- Wearable devices

Specifications
General Specifications
| Feature | Description |
|---|---|
| Sensitivity (re-arrest) | -160dBm |
| Sensitivity (Cold start) | -148dBm |
| Sensitivity (Hot start) | -160dBm |
| Horizontal accuracy | 1.5m CEP 2D RMS SBAS Auxiliary (for Open Sky) |
| Speed accuracy | 0.05m/s |
| Dynamic heading angle accuracy | 0.3 deg |
| 1PPS time accuracy | RMS 30ns (99% 60ns) |
| Cold start time | 27s |
| Hot start time | 1s |
| Assisted start time | 1s |
| Baud rate | 4800bps - 921600bps, default 38400bps |
| Output level | TTL |
| Output protocol | NMEA, UBX |
| NMEA sentences | RMC, VTG, GGA, GSA, GSV, GLL |
| Update frequency | 0.25Hz-18Hz, default 1Hz |
| Second pulse | Configurable from 0.25 Hz to 10 MHz, default period is 1s, high level lasts for 100ms |
| Max altitude | 80,000m |
| Max speed | <500m/s |
| Gravitational acceleration | <4g |
| Voltage | DC 3.6V-5.5V, typical: 5.0V |
| Current (typical) | 50mA / 5.0V |
| Size | Φ56*9.8mm (28mm*28mm*8.4mm for module only) |
| Weight | 12.0g (module only) |
| Connector | 1.25mm 6-pins connector |
| Operating temperature | -40°C ~ +85°C |
| Storage temperature | -40°C ~ +105°C |
| TX LED | Blue: Data output, TX LED flashing |
| PPS LED | Red: Not bright when GPS not fixed, flashing when fixed |
| Material | Composite Material |


Model-Specific Parameters
| Parameter | BE-450 | BK-450 | BN-450 |
|---|---|---|---|
| Chip | M10050 | M9140 | N/A |
| Working Mode | GPS, BDS, GALILEO | GPS, GLONASS, BDS, GALILEO | GPS+GLONASS+SBAS+QZSS |
| Auxiliary System | SBAS, QZSS | SBAS, QZSS | N/A |
| Channels | N/A | 92 search channels | N/A |
| Tracking Sensitivity | -166dBm | -167dBm | N/A |
| Re-acquisition Sensitivity | -160dBm | -159dBm | N/A |
| Cold Start Sensitivity | -148dBm | -148dBm | N/A |
| Horizontal Accuracy | 2.0m CEP | 1.5m CEP | N/A |
| Speed Accuracy | 0.05m/s | 0.05m/s | N/A |
| Dynamic Heading Angle Accuracy | 0.3 deg | 0.3 deg | N/A |
| PPS Time Accuracy | RMS 30ns | RMS 30ns | N/A |
| Cold Start Time | 27s | 24s | N/A |
| Hot Start Time | 1s | 2s | N/A |
| Assisted Start Time | 1s | 2s | N/A |
| Baud Rate (bps) | 4800-921600, default 38400 | 4800-921600, default 38400 | N/A |
| Output Level | TTL | TTL | N/A |
| Protocol | NMEA, UBX | NMEA, UBX | NMEA, UBX |
| Update Frequency | 0.25-18Hz, default 1Hz | 0.25-25Hz, default 1Hz | N/A |
| Voltage | 3.6-5.5V, typical: 5.0V | 3.6-5.5V, typical: 5.0V | 3.6-5.5V, typical: 5.0V |
| Current | 15mA/5.0V | 25mA/5.0V | N/A |
| Dimensions | Φ56*9.8mm | Φ56*9.8mm | Φ56*9.7mm |
| Weight | 31g | 31g | N/A |
| Connector | 1.25mm 6-pins | 1.25mm 6-pins | 1.25mm 6-pins |
| Compass | Built-in QMC5883L | Built-in QMC5883L | IST8310 |



Setup Instructions
1. Preparation
- Carefully remove all protective films or packaging materials from the GPS module.
2. Wiring
The GPS module features a 6-pin connector for power and data communication. Ensure correct pin connections to your host device (e.g., flight controller, microcontroller).
- VCC: Connect to your power supply (DC 3.6V-5.5V, typically 5.0V).
- GND: Connect to the ground of your power supply and host device.
- TX (Transmit): Connect to the RX (Receive) pin of your host device for data output from the GPS module.
- RX (Receive): Connect to the TX (Transmit) pin of your host device for sending configuration commands to the GPS module.
- SWDIO, SWCLK: These are debugging/programming pins and are typically not connected for normal operation.

3. Power Supply
Connect the module's VCC and GND pins to a certified power adapter or your host device's power output, ensuring the voltage is within the specified range (3.6V-5.5V, typical 5.0V).
4. Initial Power On
Once correctly wired, apply power to the VCC pin. The module will automatically begin the satellite acquisition process.
Operating Instructions
1. GNSS Reception
Upon power-up, the module will search for available satellite signals from supported GNSS systems (GPS, BDS, Galileo, SBAS, QZSS, and GLONASS for BK-450). For optimal performance, ensure the module has a clear, unobstructed view of the sky.
2. Data Output
The module outputs positioning and navigation data via its TX pin using standard NMEA sentences or UBX protocol, depending on configuration. The default update frequency is 1Hz, but it can be configured from 0.25Hz to 18Hz (or 25Hz for BK-450).
3. LED Indicators
- TX LED (Blue): This LED will flash when the module is actively transmitting data.
- PPS LED (Red): This LED will be off when the GPS has not acquired a satellite fix. It will start flashing once a 3D fix is achieved, indicating a Pulse Per Second signal.

Maintenance & Storage
1. Cleaning
- Turn off the device before cleaning.
- Use a soft, lint-free cloth to gently wipe the module.
- Do not use harsh chemicals, abrasive materials, or excessive moisture, as these can damage the electronic components.
2. Storage
- Store the module in a dry place at room temperature (15°C - 35°C).
- Keep away from direct sunlight, high humidity, and corrosive environments.
3. Long-term Storage
If the module is not going to be used for an extended period, it is recommended to apply power to the module for a short duration every 3 months to maintain the internal backup battery (if present) and ensure optimal performance when reactivated.
Troubleshooting
- No Satellite Fix: Ensure the module has a clear, unobstructed view of the sky. Verify that the power supply is stable and within the specified voltage range.
- No Data Output: Check the wiring connections, especially the TX and RX lines, for proper polarity and continuity. Confirm the baud rate settings on your host device match the module's default or configured baud rate.
- Inaccurate Positioning: Ensure the module is not near strong electromagnetic interference sources. Allow sufficient time for the module to acquire a stable fix, especially during a cold start.
- Compass Issues (BE-450/BK-450): Ensure the module is mounted away from magnetic interference (e.g., motors, power cables). Perform a compass calibration if supported by your flight controller or software.
Warranty & Support
If you encounter any problems such as product damage, missing parts, or have questions regarding customization or bulk orders, please contact us through the provided channels below. We will reply to you as soon as possible.
Manufacturer Information
- Manufacturer: Shenzhen DIY Maker Co., Limited
- Address: 3rd Floor, Building 81, Hekan Industrial Zone, No. 41 Wuhe South Road, Bantian, Longgang District, Shenzhen City, Guangdong Province, 518000 China
- Phone: +86 18929344627
- Email: sales09@diymalls.com
EU Responsible Person
- Company: 8eVatmaster Consulting GmbH
- Address: Bettinastr. 30, 60325 Frankfurt am Main, Germany
- Phone: 004-96995179070
- Email: contact@evatmaster.com
Disposal & Recycling
This product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.
Please dispose of packaging materials responsibly. Recycle paper, cardboard, and plastic where facilities exist. Thank you for your cooperation in protecting our environment.