Introduction
This manual provides essential information for the proper setup, operation, and maintenance of your Estardyn AHT20+BMP280 2-in-1 Temperature, Humidity, and Air Pressure Sensor Module. This module integrates the AHT20 digital temperature and humidity sensor with the BMP280 digital barometric pressure sensor, offering a comprehensive environmental sensing solution with I2C communication.
The module is designed for ease of use, featuring a simple circuit, accurate measurement points, stable and fast data transmission, and low power consumption. It operates within a DC 2.0V-5V voltage range, making it adaptable for various microcontroller projects.
Product Features
- Integrated AHT20 (Temperature & Humidity) and BMP280 (Pressure) sensors.
- I2C communication interface for easy integration.
- Wide operating voltage range: DC 2.0V-5V.
- Low power consumption.
- High precision digital output for temperature, humidity, and atmospheric pressure.
- Simple circuit design for straightforward implementation.
- Stable and fast data transmission.
Setup and Connection
Before connecting the module, ensure your development board or microcontroller is powered off. The module communicates via the I2C protocol, requiring four connections: VDD (Power), GND (Ground), SCL (Serial Clock), and SDA (Serial Data).
Pinout Diagram

Connection Steps
- Attach Pin Header: Solder the provided 4-pin header to the module if it's not already attached.
- Connect VDD: Connect the VDD pin of the module to the 2.0V-5V power supply pin of your microcontroller (e.g., 3.3V or 5V).
- Connect GND: Connect the GND pin of the module to the Ground pin of your microcontroller.
- Connect SCL: Connect the SCL pin of the module to the I2C Serial Clock pin of your microcontroller.
- Connect SDA: Connect the SDA pin of the module to the I2C Serial Data pin of your microcontroller.
- Optional: Use a 4P GROVE Test cable for quick connection if your system supports it.
Ensure all connections are secure and correctly aligned to prevent damage to the module or your microcontroller.
Operating Instructions
The AHT20+BMP280 module communicates via the I2C protocol. To operate the sensor, you will need to write code for your microcontroller (e.g., Arduino, ESP32, Raspberry Pi) to communicate with the module using its I2C address.
I2C Communication
- The AHT20 sensor typically has an I2C address of 0x38.
- The BMP280 sensor typically has an I2C address of 0x76 or 0x77.
- Libraries are available for popular microcontrollers (e.g., Adafruit AHT20 library, Adafruit BMP280 library) that simplify reading data from these sensors.
Reading Sensor Data
- Initialize I2C: In your code, initialize the I2C communication bus.
- Initialize Sensors: Initialize both the AHT20 and BMP280 sensors using their respective I2C addresses.
- Read Data:
- For AHT20: Request temperature and humidity readings.
- For BMP280: Request temperature, pressure, and altitude (derived from pressure) readings.
- Process Data: The sensor libraries will typically provide functions to read calibrated values in standard units (e.g., Celsius for temperature, %RH for humidity, hPa for pressure).
Refer to the specific sensor datasheets (AHT20, BMP280) and available microcontroller libraries for detailed programming examples and advanced configurations.
Maintenance
The AHT20+BMP280 sensor module is designed for reliable operation with minimal maintenance. Follow these guidelines to ensure its longevity and accuracy:
- Keep Dry: Avoid exposing the module to moisture or high humidity environments beyond its operating specifications, as this can damage the sensitive components.
- Cleanliness: Keep the sensor area free from dust, dirt, and debris. Do not use harsh chemicals or abrasive materials for cleaning. A soft, dry brush or compressed air can be used gently if necessary.
- Physical Protection: Handle the module with care to prevent physical damage. Avoid bending pins or applying excessive force.
- Protective Stickers: Do not remove any protective stickers or films from the sensor components unless explicitly instructed by the manufacturer. These often protect sensitive parts from environmental contaminants or damage during handling.
Troubleshooting
If you encounter issues with your AHT20+BMP280 sensor module, consider the following troubleshooting steps:
- No Readings / I2C Error:
- Verify all wiring connections (VDD, GND, SCL, SDA) are correct and secure.
- Ensure the module is receiving the correct operating voltage (DC 2.0V-5V).
- Check the I2C addresses in your code. The AHT20 is typically 0x38, and BMP280 is 0x76 or 0x77. Use an I2C scanner sketch to confirm addresses.
- Ensure pull-up resistors are correctly configured for the I2C bus if not already present on your microcontroller board or the sensor module.
- Inaccurate Readings:
- Ensure the sensor is not exposed to direct sunlight, heat sources, or strong air currents, which can affect readings.
- Avoid placing the sensor in an enclosed space where its own heat dissipation might affect temperature readings.
- Check for any physical obstructions or contaminants on the sensor surface.
- Verify that the correct sensor libraries are being used and are up-to-date.
- Module Not Detected:
- Double-check power supply and ground connections.
- Ensure the module is not damaged.
- Try connecting the module to a different I2C port or microcontroller if available, to rule out issues with the host device.
Specifications
| Attribute | Value |
|---|---|
| Model Number | AHT20 BMP280 |
| Brand Name | Estardyn |
| Type | Temperature Sensor, Humidity Sensor, Air Pressure Sensor |
| Use | Humidity Sensor (also for Temperature and Air Pressure) |
| Theory | Hall Sensor (Note: AHT20 is capacitive, BMP280 is MEMS-based) |
| Material | Polymer |
| Origin | Mainland China |
| High-concerned chemical | None |
| is_customized | Yes |
| Working Voltage | DC 2.0V-5V |
| Module Dimensions (approx.) | 1.5mm x 1.5mm (Note: This dimension likely refers to a component, not the full module board) |
| Package Length | 10 cm |
| Package Width | 4 cm |
| Package Height | 1 cm |
| Package Weight | 0.005 kg |
Module Overview Images


User Tips
- Protective Sticker: It is generally recommended not to remove any white stickers or films from the sensor components unless explicitly instructed. These often serve as protection for sensitive parts from dust, moisture, or physical damage during manufacturing and handling.
- I2C Address Conflicts: If using multiple I2C devices, ensure there are no address conflicts. The AHT20 and BMP280 have distinct addresses, but other devices on the same bus might conflict.
- Power Supply Stability: Provide a stable power supply within the specified voltage range (DC 2.0V-5V) for optimal performance and accurate readings.
Warranty and Support
For technical support, troubleshooting assistance, or warranty inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.