9IMOD F405 V3.1S PLUS FC & 60A ESC

Contents

9IMOD F405 V3.1S PLUS Flight Controller and 60A ESC Instruction Manual

Model: F405 V3.1S PLUS FC & 60A ESC

For RC QAV 230 250 FPV Racing Drones

1. Introduction

The 9IMOD F405 V3.1S PLUS FC Flight Controller Board and 4-in-1 60A ESC is a high-performance combination designed for RC FPV racing drones. It features an F405 MCU, built-in barometer, OSD, and a robust 60A continuous current ESC. This manual provides essential information for the proper setup, operation, and maintenance of your flight controller and ESC.

9IMOD F405 V3.1S PLUS and 60A ESC, highlighting high load capacity and strong filtering ability.

Figure 1: 9IMOD F405 V3.1S PLUS FC and 60A ESC overview.

2. Package Contents

Please verify that all items listed below are included in your package:

  • F405 V3.1S PLUS Flight Controller
  • 4-in-1 60A ESC
  • Wiring harness (for FC to ESC connection)
  • Power cable (red/black)
  • Capacitor (1000uF 35V)
  • XT60 connector
  • Mounting hardware (screws, nuts, rubber grommets)
Components included in the F4 V3.1S PLUS FC + 4-in-1 60A ESC kit, including wires, capacitor, and mounting hardware.

Figure 2: Included components of the F4 V3.1S PLUS FC and 4-in-1 60A ESC kit.

3. Specifications

3.1. Flight Controller (F4 V3.1S PLUS FC)

Feature Detail
MCUSTM32F405
GyroICM-42688-P
BarometerBMP280
OSDDrag and drop OSD configured by Betaflight
Dshot SupportYes
PortsSbus/CRSF and Spektrum DSMX ports
Black BoxMemory card black box
BEC5V3.1A, 9V3.1A
Video FilterOn-board (only 5V to VTX and camera)
Size36 x 36mm
Mounting Hole Distance30.5 x 30.5mm
Weight9g
Top view of the F405 V3.1S PLUS Flight Controller, showing MCU, gyro, and various pads.

Figure 3: F405 V3.1S PLUS Flight Controller board layout.

3.2. Electronic Speed Controller (BLHeli_S 4IN1_60V1)

Feature Detail
Continuous Current60A
Instantaneous Current70A (10s)
BECNo
Current SensorYes
Battery Sections2-6S LiPo
Dimensions37 x 42.7mm
Mounting Hole Distance30.5 x 30.5mm
Weight14g
MicroprocessorEFM8BB21F16G (up to 48MHz)
PCB6 layers, high TG 3OZ copper thick
FirmwareBLHeli_S open source
Throttle ModesDShot150/300/600, normal PWM, OneShot125, OneShot42, MultShot
Top view of the 4-in-1 60A ESC, showing power pads and capacitors.

Figure 4: 4-in-1 60A ESC board layout.

Dimensions of the F4 V3.1S PLUS FC (36x36mm, 9g) and 4-in-1 60A ESC (37x42.7mm, 14g), both with 30.5x30.5mm mounting holes.

Figure 5: Dimensions and weight of the Flight Controller and ESC.

4. Setup

4.1. Physical Installation

Both the Flight Controller and the 4-in-1 ESC are designed for 30.5x30.5mm mounting patterns. Use the provided rubber grommets and screws to mount the boards securely in your drone frame. The rubber grommets help to isolate vibrations, which is crucial for stable flight performance.

4.2. Wiring

Careful wiring is essential for proper function and to prevent damage. Refer to the following steps and diagrams:

  1. Connect FC to ESC: Use the provided wiring harness to connect the Flight Controller to the 4-in-1 ESC. Ensure correct pin alignment for signal, ground, and power connections.
  2. Main Power: Solder the main power cable (red/black) to the designated battery pads on the 4-in-1 ESC.
  3. Capacitor: Solder the included 1000uF 35V capacitor across the main battery terminals on the ESC. Ensure correct polarity (positive to positive, negative to negative) for effective power filtering.
  4. Motors: Connect your drone's motors to the corresponding motor pads (M1-M4) on the 4-in-1 ESC.
  5. Receiver: Connect your radio receiver (Sbus/CRSF/DSMX) to the appropriate pads on the Flight Controller.
  6. VTX & Camera: Connect your Video Transmitter (VTX) and FPV Camera to the designated pads on the Flight Controller. The FC provides an on-board video filter for 5V output to VTX and camera.
F405 V3.1S PLUS Flight Controller with connected wiring harness.

Figure 6: Flight Controller with wiring harness connected.

F405 V3.1S PLUS FC and 60A ESC kit, emphasizing Dual BEC, 2-6S LiPo support, and current sensor.

Figure 7: Wiring overview for FC and ESC, showing power and signal connections.

4.3. Software Configuration

After physical installation and wiring, configure the flight controller using Betaflight software:

  1. Connect to PC: Connect the Flight Controller to your computer via a USB cable.
  2. Betaflight Configurator: Open the Betaflight Configurator software.
  3. Firmware: Flash the latest stable Betaflight firmware for the STM32F405 target.
  4. Sensor Calibration: Calibrate the accelerometer and gyroscope.
  5. OSD Configuration: Configure the On-Screen Display (OSD) to show desired flight data.
  6. Receiver Setup: Configure your receiver type and channel mapping.
  7. ESC Configuration: The ESC uses BLHeli_S open source firmware. You can update firmware or change parameters via the throttle signal line using BLHeliSuite software.

5. Operating Instructions

  1. Pre-Flight Check: Before each flight, ensure all connections are secure, propellers are correctly installed, and the battery is fully charged.
  2. Power On: Connect a compatible 2-6S LiPo battery to the main power lead of the ESC. The flight controller and ESC will emit initialization tones.
  3. Arming: Arm the motors using the designated switch or stick command on your radio transmitter. Ensure you are in a safe area before arming.
  4. Flight: Perform flight operations, monitoring the OSD for critical flight data such as battery voltage, current consumption, and flight mode.
  5. Disarming: Disarm the motors after landing to prevent accidental propeller spin.

6. Maintenance

  • Inspection: Regularly inspect all solder joints and electrical connections for any signs of damage, corrosion, or looseness.
  • Cleaning: Keep the flight controller and ESC boards clean and free from dust, dirt, and moisture. Use compressed air or a soft brush for cleaning.
  • Physical Protection: Avoid physical impacts to the boards, as this can damage sensitive electronic components.
  • Temperature Monitoring: Periodically check for any signs of overheating, such as discolored components or burnt smells. Ensure adequate airflow around the FC and ESC during operation.
  • Firmware Updates: Keep your flight controller and ESC firmware updated to the latest stable versions to benefit from performance improvements and bug fixes.

7. Troubleshooting

Problem Possible Cause / Solution
No power to FC/ESCCheck battery connection, main power cable, and ensure no short circuits. Verify battery voltage.
Motors not spinning or erratic behaviorVerify ESC calibration, motor direction, and DShot/PWM protocol settings in Betaflight. Check motor connections to ESC. Ensure propellers are not obstructed.
Unstable flight / DriftingRe-calibrate accelerometer and gyroscope in Betaflight. Check for loose mounting or excessive vibrations. Ensure PID tuning is appropriate for your drone setup.
OSD not displaying informationCheck OSD settings in Betaflight. Ensure video signal from camera to FC and FC to VTX is correctly wired and configured.
Loss of radio signalCheck receiver connections to the FC and ensure it is properly bound to your radio transmitter. Verify receiver protocol settings in Betaflight.

8. User Tips

  • Capacitor Installation: It is highly recommended to install the provided low ESR capacitor to the main battery leads of the ESC. This helps to filter power and reduce voltage spikes, especially when using higher cell count batteries (e.g., 6S), contributing to cleaner power and longer component life.
  • Motor Direction: Always double-check motor spin direction in Betaflight's motor tab before your first flight. Incorrect motor direction can lead to immediate crashes upon arming.
  • Firmware Updates: For optimal performance and access to the latest features, ensure both your Betaflight firmware (for the FC) and BLHeli_S firmware (for the ESC) are kept up to date.

9. Warranty and Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For technical support or warranty claims, please contact the seller or manufacturer directly with your purchase details. Keep your proof of purchase for any warranty-related inquiries.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.